background image
UNIVERSAL CONTROL PANEL
UCP-8060
MAINTENANCE MANUAL
1st Edition
Serial No. 10001 and Higher


background image
UCP-8060
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin
de réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les
réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres.
Pour toute réparation faire appel à une personne compétente uniquement.


background image
UCP-8060
For the U.S.A
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the rear of
the unit 10 cm (4 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.
WARNING
This unit has no power switch.
When installing the unit, incorporate a readily
accessible disconnect device in the fixed wiring, or
connect the power cord to a socket-outlet which must
be provided near the unit and easily accessible, so that
the user can turn off the power in case a fault should
occur.
WARNUNG
Dieses Gerät hat keinen Netzschalter.
Beim Einbau des Geräts ist daher im Festkabel ein
leicht zugänglicher Unterbrecher einzufügen, oder das
Netzkabel mu
ß mit einer in der Nähe des Geräts
befindlichen, leicht zugänglichen Wandsteckdose
verbunden werden, damit sich bei einer
Funktionsstörung die Stromversorgung zum Gerät
jederzeit unterbrechen lä
ßt.
When using a LAN cable:
For safety,do not connect to the connector for
peripheral device wiring that might have excessive
voltage.
1 (P)


background image


background image
1 (E)
UCP-8060
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals ................................................................................................... 3 (E)
Contents ............................................................................................................... 4 (E)
Trademarks .......................................................................................................... 4 (E)
1. Service Overview
1-1.
Removing the Upper Panel ................................................................... 1-1 (E)
1-2.
Main Parts Location .............................................................................. 1-1 (E)
1-3.
System Indicator and Status Indicator ................................................... 1-2 (E)
1-3-1.
System Indicator ................................................................... 1-2 (E)
1-3-2.
Status Indicator ..................................................................... 1-2 (E)
1-4.
Troubleshooting .................................................................................... 1-3 (E)
1-5.
Replacing the Board .............................................................................. 1-8 (E)
1-5-1.
MB-978 Board ..................................................................... 1-8 (E)
1-5-2.
CPU-352 Board .................................................................... 1-9 (E)
1-5-3.
TouchEngine Board ............................................................. 1-9 (E)
1-6.
Replacing the Main Parts .................................................................... 1-10 (E)
1-6-1.
Switching Regulator ........................................................... 1-10 (E)
1-6-2.
Rotary Encoder ................................................................... 1-11 (E)
1-6-3.
Inverter Unit ....................................................................... 1-12 (E)
1-6-4.
LCD Panel .......................................................................... 1-13 (E)
1-6-5.
Back Light .......................................................................... 1-14 (E)
1-6-6.
Touch Panel ........................................................................ 1-14 (E)
1-7.
Replacing the Fuse/IC Link ................................................................ 1-15 (E)
1-8.
Initializing System Setting Value ........................................................ 1-15 (E)
1-9.
System File Recovery ......................................................................... 1-16 (E)
2. Spare Parts
2-1.
Notes on Repair Parts .................................................................................. 2-1
2-2.
Exploded Views .......................................................................................... 2-2
2-3.
Electrical Parts List ..................................................................................... 2-5
2-4.
Supplied Accessories List ......................................................................... 2-10
2-5.
Power Cords List ....................................................................................... 2-10
2-6.
Optional Fixtures List ............................................................................... 2-10