background image
MICROFILM
SERVICE MANUAL
Korean Model
SLV-ED7KR
Philippine Model
SLV-ED1PL/ED4PL/ED8PL
RMT-V247B/V248
VIDEO CASSETTE RECORDER
SLV-ED1PL/ED4PL/ED7KR/ED8PL
G
· Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENTS VI for MECHANICAL ADJUSTMENTS.
(9-921-647-11)
* The abbreviations of ED1, ED4, ED7 and ED8 contained in this service manual
are indicated when these models are common to all their corresponding mod-
els as given below.
Photo: SLV-ED1PL
S MECHANISM
ED1PL
ED1
Abbreviated
model name
All model
names
SLV-
ED4PL
ED4
ED7KR
ED7
ED8PL
ED8
SPECIFICATIONS
­ Continued on next page ­
Inputs and outputs
LINE-1 IN
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
AUDIO IN, phono jack (1) (ED1/ED4)
AUDIO IN, phono jack (2) (ED7/ED8)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE-2 IN (ED7/ED8)
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
AUDIO IN, phono jack (2)
Input level: 327mVrms
Input impedane: more than 47 kilohms
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbal-
anced, sync negative
AUDIO OUT, phono jack (1) (ED1/ED4)
AUDIO OUT, phono jack (2) (ED7/ED8)
Standard output: 327 mVrms
Load impedance; 47 kilohms
Output impedance: less than 10 kilohms
Timer section
Clock
Quartz locked
Timer indication
12-hour cycle
Timer setting
8 programs per month (max.)
Power back-up
Built-in self-charging capacitor
Back-up duration: up to 1 hour at a time
General
Power requirements
110 ­ 240 V AC, 50/60 Hz
Power consumption
19W (ED1/ED4)
22W (ED7/ED8)
Operating temperature
5 °C to 40 °C
Storage temperature
­20 °C to 60 °C
System
Format
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Double azimuth two heads
Video signal
NTSC color, EIA standards
Tape speed
SP: 33.35 mm/s
EP: 11.11 mm/s
LP: 16.67 mm/s, playback only
Maximum recording
playback time
8 hrs. in EP mode (with T-160 tape)
Fast-forward and rewind time
Approx. 3 min. (with T-120 tape)
Tuner section
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W
+1 to W+84
Antenna
75-ohm antenna terminal for VHF/UHF
Ver 1.0 1998. 08


background image
­ 2 ­
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recom-
mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED
LINE WITH MARK
! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
· Feature Difference
SLV-
ED1PL
ED4PL
ED7KR
ED8PL
FEATURE
HEAD/CH
2/2
4/4
4/6
4/6
RCA REAR LINE IN/OUT
®/®®/®®(3P)/®(3P) ®(3P)/®(3P)
RCA FRONT LINE IN
GG
®(3P)
®(3P)
CLICK SHUTTLE
GG
G
®
REMOTE COMMANDER RMT-
V248
V248
V247B
V247B
Dimensions
Approx. 355
× 96 × 285 mm (w/h/d): (ED1)
Approx. 430
× 100 × 286 mm (w/h/d):
(ED4/ED7/ED8)
including projecting parts and controls
Mass
Approx. 3.7 kg: (ED1)
Approx. 4.2 kg: (ED4/ED7/ED8)
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
75-ohm coaxial cable with F-type connectors (1)
Plug adaptor (1) (ED1/ED4/ED8)
Design and specifications are subject to change
without notice.


background image
­ 3 ­
TABLE OF CONTENTS
Section
Title
Page
Section
Title
Page
Feature Difference ................................................................... 2
SERVICE NOTE ...................................................................... 4
1.
GENERAL
Getting Started .............................................................. 1-1
Basic Operations ........................................................... 1-4
Additional Operations .................................................... 1-7
Additional Information ................................................... 1-9
2.
DISASSEMBLY
2-1.
Upper Case Removal .................................................... 2-1
2-2.
NK-11 Board Removal .................................................. 2-1
2-3.
Rear Panel Removal ..................................................... 2-1
2-4.
Front Panel Section Removal ....................................... 2-1
2-5.
Power Block Removal ................................................... 2-2
2-6.
Mechanism Deck Removal ........................................... 2-2
2-7.
MA-323 Board Removal ................................................ 2-2
2-8.
Internal Views ................................................................ 2-3
2-9.
Circuit Boards Location ................................................. 2-4
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram .................................................. 3-1
3-2.
Video1 Block Diagram ................................................... 3-4
3-3.
Video2 Block Diagram ................................................... 3-5
3-4.
Servo/System Control Block Diagram .......................... 3-7
3-5.
Audio Block Diagram ..................................................... 3-9
3-6.
Tuner Block Diagram ..................................................... 3-11
3-7.
Mode Control Block Diagram ........................................ 3-13
3-8.
Power Block Diagram .................................................... 3-15
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagram ............................................ 4-3
4-2.
Printed Wiring Boards and Schematic Diagrams ......... 4-5
MA-323 (Head Amp) Schematic Diagram .................... 4-5
MA-323 Printed Wiring Board ....................................... 4-9
MA-323 (Video, Audio) Schematic Diagram ................. 4-11
MA-323 (System Control) Schematic Diagram ............ 4-15
MA-323 (Servo Control) Schematic Diagram ............... 4-17
MA-323 (Hi-Fi Audio) Schematic Diagram .................... 4-19
MA-323 (IO) Schematic Diagram .................................. 4-21
MA-323 (Tuner) Schematic Diagram ............................ 4-23
MA-323 (Mode Control) Schematic Diagram ................ 4-25
MA-323 (FL Driver) Schematic Diagram ....................... 4-27
MA-323 (Power Supply) Schematic Diagram ............... 4-29
DS-80 Printed wiring Board and
Schematic Diagram ....................................................... 4-31
NK-11 Printed wiring Board and
Schematic Diagram ....................................................... 4-33
DM-76, MF-312
Printed Wiring Board and Schematic Diagram ............. 4-35
HS-921SF/921SF1 Printed Wiring Board ..................... 4-37
HS-921SF/921SF1 Schematic Diagram ....................... 4-39
SR-708 Printed Wiring Board ........................................ 4-41
SR-708 Schematic Diagram ......................................... 4-43
5.
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-1.
System Control-Video Block Interface
(MA-323 board IC161) .................................................. 5-1
5-2.
System Control-Servo Peripheral Circuit Interface
(MA-323 board IC161) .................................................. 5-1
5-3.
System Control-Mechanism Block Interface
(MA-323 board IC161) .................................................. 5-2
5-4.
System Control-Audio Block Interface
(MA-323 board IC161) .................................................. 5-3
5-5.
Servo/System/Tuner/Timer Control Microprocessor
Pin Function (MA-323 board IC161) ............................. 5-4
5-6.
Korean Stereo Processor Pin Function
(NK-11 board IC1) ......................................................... 5-5
6.
ERROR CODES ....................................................... 6-1
7.
ADJUSTMENTS
7-1.
Mechanical Adjustments ............................................... 7-1
7-2.
Electrical Adjustments ................................................... 7-1
2-1.
Pre-Adjustment Preparations ........................................ 7-1
2-1-1. Instruments to be Used ............................................ 7-1
2-1-2. Connection ............................................................... 7-1
2-1-3. Set-up of Adjustment ................................................ 7-1
2-1-4. Alignment Tape ......................................................... 7-1
2-1-5. Specified I/O Level and Impedance ......................... 7-1
2-1-6. Adjusting Sequence ................................................. 7-2
2-2.
Power Supply Adjustment ............................................. 7-2
2-2-1. Power Supply Check ................................................ 7-2
2-2-2. +6V Adjustment ........................................................ 7-2
2-3.
Servo System Adjustment ............................................. 7-2
2-3-1. Switching Position Adjustment ................................. 7-2
2-4.
Audio System Adjustments ........................................... 7-3
2-4-1. Hi-Fi Audio System Adjustment ............................... 7-3
1.
AF Switching Position Adjustment ........................... 7-3
2.
Frequency Response Check .................................... 7-3
3.
Overall Level Characteristic and
Distortion Factor Check ........................................... 7-4
4.
Overall S/N Check .................................................... 7-4
2-4-2. Normal Audio System Adjustment ........................... 7-4
1.
ACE Head Adjustment ............................................. 7-4
2.
E-E Output Level Check .......................................... 7-4
3.
Frequency Responce Check .................................... 7-4
4.
Overall Level Characteristic and Distortion
Factor Check ............................................................ 7-5
5.
Overall S/N Check .................................................... 7-5
2-5.
Tuner System Adjustment ............................................. 7-5
2-5-1. Separation Adjustment ............................................. 7-5
2-6.
Parts Arrangement Diagram for Adjustments ............... 7-6
8.
REPAIR PARTS LIST
8-1.
Exploded Views ............................................................. 8-1
8-1-1. Front Panel and Cabinet Assemblies (ED1) ........... 8-1
8-1-2. Chassis Assembly (ED1) ......................................... 8-2
8-1-3. Front panel and Cabinet Assemblies
(ED4/ED7/ED8) ........................................................ 8-3
8-1-4. Chassis Assembly (ED4/ED7/EZ8) ......................... 8-4
8-1-5. Mechanism Chassis Assembly (1) ........................... 8-5
8-1-6. Mechanism Chassis Assembly (2) ........................... 8-6
8-1-7. Mechanism Chassis Assembly (3) ........................... 8-7
8-2.
Electrical Parts List ....................................................... 8-8


background image
­ 4 ­
SERVICE NOTE
1. DISASSEMBLY
· This set can be disassembled in the order shown below.
Note: Pages in
indicated pages in the SERVICE MANUAL.
Pages in
indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
NK-11Board
(ED7)
(Page 2-1)
Set
Upper case
(Page 2-1)
Front Panel
Section
(Page 2-1)
Power
Block
(Page 2-2)
Pinch Press
Block Ass'y
(Page 14)
Ground Shaft
Ass'y
(Page 13)
Mechanism
Deck
(Page 2-2)
FL Complete
Ass'y
(Page 13)
Drum
Ass'y
(Page 13)
Rear
Panel
(Page 2-1)
Rubber
Belt
(Page 15)
Rubber
Belt
(Page 15)
Slider
(Page 26)
Loading
Gear (T, S)
(Page 28)
Retainer
Plate
(Page 22)
MA-323
Board
(Page 2-2)
Rubber
Belt
(Page 15)
Capstan
Motor
(Page 15)
FL Slider
Block Ass'y
(Page 22)
Rotary
Switch
(Page 2-2)
Tuner
Unit
Pully Gear
Ass'y
(Page 29)
Cam Motor
Retainer
(Page 31)
Cam Gear
(Page 23)
Cam Motor
(Page 31)
Reel Direct
Ass'y
(Page 30)


background image
1-1
SECTION 1
GENERAL
This section is extracted from SLV-
ED1PL instruction manual.
SLV-ED1/ED4/ED7/ED8