background image
­ 1 ­
SERVICE MANUAL
AEP Model
UK Model
PMC-R30L
PERSONAL COMPONENT SYSTEM
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/­2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM
87.5 - 108 MHz
MW
531 - 1,602 kHz
LW
153 - 279 kHz
IF
FM: 10.7 MHz
MW/LW: 450 kHz
Aerials
FM: External aerial terminal
MW/LW: External aerial terminal
­ Continued on next page ­
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 10,000 Hz
General
Speaker
Full range: 10 cm dia.,
3 ohms, cone type
(2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
Maximum power output
4.5 W + 4.5 W
Power requirements
For personal component system:
230 V AC, 50 Hz
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 23 W
CD
Model Name Using Similar Mechanism PMC-107L
Section
CD Mechanism Type
KSM-213CDM
Optical Pick-up Name
KSS-213C
TC
Model Name Using Similar Mechanism PMC-107L
Section Tape Transport Mechanism Type
MF-107
SPECIFICATIONS
MICROFILM
Ver 1.0 1999. 07


background image
­ 2 ­
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE
WITH MARK
! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Dimensions (incl. projecting parts)
Player: Approx. 160
× 249 × 227 mm (w/h/d)
Speaker: Approx. 150
× 245 × 192 mm (w/h/d)
Mass
Player: Approx. 2.8 kg
Speaker: Approx. 1.2 kg
Supplied accessories
Remote control RMT-C107AD (1)
FM lead aerial (1)
MW/LW loop aerial (1)
Design and specifications are subject to change without
notice.
TABLE OF CONTENTS
1. SERVICING NOTES ......................................................... 3
2. GENERAL
Playing a CD ........................................................................... 4
Listening to the radio ............................................................... 4
Playing a tape .......................................................................... 5
Recording on a tape ................................................................. 5
3. DISASSEMBLY
3-1. Cabinet (Front) Assy ........................................................... 6
3-2. Cabinet (Upper) Assy .......................................................... 7
3-3. Power Board ........................................................................ 7
3-4. Main Board ......................................................................... 8
3-5. CD Board ............................................................................ 8
3-6. Optical Pick-up ................................................................... 9
3-7. Tape Mechanism Block ....................................................... 9
3-8. Control Board and Back Light Board ............................... 10
3-9. How to Apply the Belts ..................................................... 10
3-10. Head, Magnetic (HRP301) ................................................ 11
3-11. Motor Assy (M301) ........................................................... 11
4. MECHANICAL ADJUSTMENTS ............................... 12
5. ELECTRICAL ADJUSTMENTS
Tape Section .......................................................................... 12
Tuner Section ......................................................................... 13
CD Section ............................................................................ 14
6. DIAGRAMS
6-1. IC Pin Description ............................................................. 15
6-2. Circuit Boards Location .................................................... 16
6-3. Block Diagram ­CD Section­ ........................................... 17
6-4. Block Diagram ­Main Section­ ........................................ 19
6-5. Printed Wiring Boards ­CD Section­ ............................... 21
6-6. Schematic Diagrams ­CD Section­ .................................. 23
6-7. Printed Wiring Boards ­Control Section­ ......................... 25
6-8. Schematic Diagrams ­Control Section­ ........................... 27
6-9. Printed Wiring Boards ­Main Section­ ............................ 29
6-10. Schematic Diagram ­Main Section (1/2)­ ........................ 31
6-11. Schematic Diagram ­Main Section (2/2)­ ........................ 33
6-12. Printed Wiring Board ­Power Supply Section­ ................ 35
6-13. Schematic Diagram ­Power Supply Section­ ................... 35
7. EXPLODED VIEWS
7-1. Cabinet (Rear) Section ...................................................... 40
7-2. Cabinet (Front) Section ..................................................... 41
7-3. Cabinet (Upper) Section .................................................... 42
7-4. Tape Mechanism Section-1 ............................................... 43
7-5. Tape Mechanism Section-2 ............................................... 44
7-6. Tape Mechanism Section-3 ............................................... 45
7-7. Tape Mechanism Section-4 ............................................... 46
7-8. Optical Pick-up Section .................................................... 47
7-9. Speaker Section ................................................................. 48
8. ELECTRICAL PARTS LIST ......................................... 49


background image
­ 3 ­
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
· Code number of Chuck Plate Jig: X-4918-255-1
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
This Compact Disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT table is
location on the rear exterior.
SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Open the CD lid.
2. Turn OPERATE switch on with to set the CD.
3. Turn on SW701 as following figure.
4. Press the
^ (CD) button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
Push on SW701 in the
arrowed direction with
a screwdriver, etc.
SW701


background image
­ 4 ­
SECTION 2
GENERAL
This section is extracted
from instruction manual.


background image
­ 5 ­