3-266-173-21(1)
FM/AM PLL Synthesized Clock Radio
ICF-C763
Operating Instructions
Features
· Dual alarm FM/AM PLL (Phase Locked Loop)
synthesized clock radio.
· LCD with white backlight, and brightness
adjustment for the backlight.
· Easy preset digital tuning with 15 memory presets.
· Illumination light, that is most suitable as a bedside
interior.
·Various types of alarms-radio, buzzer and 4
melodies.
·Nap Timer allows you to take a short nap and wake
to buzzer without changing your alarm settings.
(You can select your nap time from 10 to 120
minutes)
· Angle is adjustable for your best view position.
· DST(Daylight Saving Time) -Summer time
adjustment (one-hour skip function).
· Extendable snooze - snooze time can be extended
from 10 to 60 minutes in maximum every time you
use.
Precautions
· Operate the unit only on 120V AC, 60 Hz.
·The nameplate indicating voltage, etc. is located at
the bottom of the unit.
·To disconnect the power cord (mains lead), pull it
out the plug, not by the cord.
· Do not leave the unit in a location near a heat source
such as a radiator or airduct, or in a place subject to
direct sunlight, excessive dust, mechanical
vibration, or shock.
· Do not place the unit on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that
block the ventilation holes.
· Should any liquid or solid object fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it further.
· When the casing becomes soiled, clean it with a soft
cloth dampened with a mild detergent solution.
Never use abrasive cleaners or chemical solvents, as
they may mar the casing.
·The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
Troubleshooting
Should any problem occur with the unit, make the
following simple checks to determine whether or not
servicing is required.
If the problem persists, consult your nearest Sony
dealer.
The clock does not show the correct time.
· Has an electrical power outage lasting more than 1
minute occurred?
The radio or buzzer alarm does not sound at
the preset alarm time.
· Has the desired radio or buzzer alarm been
activated? (i.e. Is "
" or "
" displayed?)
The radio alarm is activated but no sound
comes on at the preset alarm time.
· Has VOLUME been adjusted?
The preset stations may be deleted from the memory,
if a maintenance service is required.
Please note down your settings in case you want to
preset them again.
Specifications
Time display
12-hour system
Frequency range
FM:
87.5 - 108 MHz
AM:
530 - 1 710 kHz
Speaker
Approx. 5.7 cm (2 1/
4 inches) dia. 4
Power output
200 mW (at 10 % harmonic distortion)
Power requirements
120 V AC, 60 Hz
Dimensions
Approx. 115.5
× 105 × 110.6 mm (w/h/d) (4 5/
8 ×
4 1/
4 × 4
3/
8 inches) including projecting parts and
controls
Mass
Approx. 600 g (1 lb 5.2 oz)
Design and specifications are subject to change
without notice.
© 2004 Sony Corporation
Printed in China
Dream Machine is a trademark of Sony Corporation.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
IMPORTANT SAFEGUARDS
For your protection, please read these safety instructions completely before operating the appliance,
and keep this manual for future reference.
Carefully observe all warnings, precautions and instructions on the appliance and in the operating
instructions, and adhere to them.
INSTALLATION
Water and Moisture
Do not use powerline operated appliances near water - for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
Heat
Do not place the appliance near or over a radiator or heat register, or where it is exposed to direct
sunlight.
Ventilation
The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable
operation of the appliance, and to protect it from overheating, these slots and openings must never be
blocked or covered.
-Never cover the slots and openings with a cloth or other materials.
-Never block the slots and openings by placing the appliance on a bed, sofa, rug or other similar
surface.
-Never place the appliance in a confined space, such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
Accessories
Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or an adult, and serious damage to the appliance. Use only a cart,
stand, tripod, bracket, or table recommended by Sony.
-An appliance and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
Wall or Ceiling Mounting
If your appliance can be mounted to a wall or ceiling, mount it only as recommended by Sony.
USE
Power Source
This appliance should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of electrical power supplied to your home, consult your dealer or local
power company. For those appliances designed to operate from battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization
This appliance is equipped with a polarized AC power cord plug (a plug having one blade wider than
the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow
the instructions below:
-For the appliance with a polarized AC power cord plug:
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized
plug by forcing it in.
-For the appliance with a three-wire grounding type AC plug:
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat
the safety purpose of the grounding plug.
Overloading
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since
this can result in fire or electric shock.
When not in use
Unplug the power cord of the appliance from the outlet when left unused for a long period of time.
To disconnect the cord, pull it out by grasping the plug. Never pull the plug out by the cord.
Power-Cord Protection
Route the power cord so that it is not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to the plugs, receptacles, and the point where the cord exits
from the appliance.
Lightning
For added protection for this appliance during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the appliance due to lightning and powerline surges.
Object and Liquid Entry
Never push objects of any kind into the appliance through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any
kind on the appliance.
Cleaning
Unplug the appliance from the wall outlet before cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the appliance.
Clean the appliance only as recommended by Sony.
Attachments
Do not use attachments not recommended by Sony, as they may cause hazards.
ANTENNAS
Outdoor Antenna Grounding
If an outdoor antenna or cable system is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN
TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM
IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810 of the National Electrical Code provides information with respect
to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the National
Electrical Code
SERVICE
Damage Requiring Service
Unplug the appliance from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
-When the power cord or plug is damage or frayed.
-If liquid has been spilled or objects have fallen into the appliance.
-If the appliance has been exposed to rain or water.
-The appliance does not appear to operate normally or exhibits a marked change in performance.
-This indicates a need for service.
-If the appliance does not operate normally when following the operating instructions, adjust only
those controls that are specified in the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive work
by a qualified technician to restore the appliance to normal operation.
-If the appliance has been subject to excessive shock by being dropped, or the cabinet has been
damaged.
Servicing
Do not attempt to service the appliance yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by Sony that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the appliance, ask the service technician to perform
routine safety checks (as specified by Sony) to determine that the appliance is in safe operating
condition.
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-20)
Antenna Lead-in Wire
Ground
Clamps
NEC-NATIONAL
ELECTRICAL CODE
Electric Service
Equipment
Ground Clamps
Power Service Grounding Electrode System
(NEC Art 250 Part H)
For customers who purchased this product in the
USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send you
periodic mailings about new products, services,
and other important announcements.
Registering your product will also allow us to
contact you in the unlikely event that the product
needs adjustment or modification. Thank you.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
This symbol is intended to alert the user
to the presence of uninsulated
"dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instruc-
tions in the literature accompanying the
appliance.
* The graphical symbols are the bottom
enclosure of the AC power adaptor.
INFORMATION
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/
TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
Owner's Record
The model number and the serial number are located
on the bottom.
Record the serial number in the space provided below.
Refer to them whenever you call upon your Sony
dealer regarding this product.
Model No. ICF-C763
Serial No.
Setting the Clock
1 Plug in the clock radio.
"AM 12:00" flashes on the display.
2 Press D.S.T./CLOCK for a few seconds
until a beep sounds.
The hour starts to flash on the display.
3 Press TUNE/TIME SET + or until the
correct hour appears.
To set the current time rapidly, hold down TUNE/
TIME SET + or .
4 Press D.S.T./CLOCK once.
5 Repeat steps 3 and 4 to set the minute.
Two short beeps sound, and the counting of the
seconds starts.
If you quit during the clock setting, after about 65
seconds the previous display will return.
To set the current time from zero seconds, press
D.S.T./CLOCK with the time signal in step 5.
To change the display to the daylight saving
time (summer time) indication
Press D.S.T./CLOCK.
"
" is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
D.S.T./CLOCK again.
Setting the
Brightness of the
Backlight
Press BRIGHTNESS to select high, middle or low
for the display according to your preferences.
Changing AM
Channel Step
The AM channel step differs depending on areas. The
channel step of this unit is factory-set to 10 kHz.
Change the settings as shown below to be able to
listen to the radio.
Area
Channel step
North and South America
10 kHz
Other countries/regions
9 kHz
1 Press RADIO ON·OFF to turn off the
power.
2 While holding down BAND, keep pressing
RADIO ON·OFF for more than 5
seconds.
Two short beeps sound, and the AM channel step
will be changed.
If you proceed to step 2 again, the channel step
changes again.
Notes
·When the AM channel step is changed, the preset
stations will be initialized.
·When the AM channel step is changed, the FM
channel step is also changed.
Playing the Radio
Manual Tuning
1 Press RADIO ON·OFF to turn on the
radio.
The display shows the band and frequency for 10
seconds and then changes back to the current
time.
2 Press BAND to select the band.
Each press changes the band as follows:
AM
FM1
FM2
When using FM1 or FM2 preset mode, you may
listen to the radio on either mode. (See "Preset
Tuning".)
3 Press TUNE/TIME SET + or to tune
into the desired station.
The FM channel step is set to 0.1 MHz and the
AM channel step is set to 10 kHz (North and
South American model).
The FM channel step is set to 0.05 MHz* and the
AM channel step is set to 9 kHz (Other models).
*The FM frequency display is raised or lowered by
a step of 0.1 MHz. For example, frequency 88.00
and 88.05 MHz is displayed as "88.0 MHz."
Two short beeps sound when the minimum
frequency of each band is received during tuning.
4 Adjust volume using VOLUME.
To turn off the radio, press RADIO ON·OFF.
To check the station being received
Press TUNE/TIME SET + or lightly. The display
shows the band and frequency for 10 seconds and then
returns to the previous display.
Improving the
Reception
FM: The AC power cord functions as an FM
antenna. Extend the AC power cord fully to
increase reception sensitivity.
AM: Rotate the unit horizontally for optimum
reception. A ferrite bar is built into the unit.
Do not operate the unit over a steel desk or metal
surface, as this may lead to interference of reception.
Presetting Your
Favorite Station
Preset Tuning
You can preset up to 10 stations in FM (5 stations in
FM1, 5 stations in FM2), and 5 stations in AM.
Presetting a Station
1 Follow steps 1 to 4 in "Playing the Radio"
and manually tune into the station you wish
to preset.
2 Hold down the PRESET 1 to 5 button
you wish to preset for more than 2 seconds.
Example: Display window when you set FM
90 MHz in the PRESET 2 button for
FM2.
A RADIO
SLEEP
FM12
MW
AM
LW
PM
MHz kHz
RADIO
B SOUND 12345
WAKE UP
PRESET
The preset number "2" and "
" flash in the
display.
Two beeps sound, and "2" and "
" stop
flashing.
To preset another station, repeat these steps.
To change the preset station, tune into the desired
station and hold down the PRESET 1 to 5
button. The new station will replace the previous
station on the preset button.
Tuning into a Preset Station
1 Press RADIO ON·OFF to turn on the
radio.
2 Press BAND to select the band.
3 Press the desired PRESET 1 to 5 button.
4 Adjust the volume using VOLUME.
After 10 seconds, the display will return to the
current time but the preset button number will
remain.
Tip
In step 3, you can also choose a preset station using
the PRESET button at the side of this unit.
Press PRESET repeatedly until the desired mode is
selected.
Each time of PRESET changes as follows.
PRESET 1
2
3
4
5
Two short beeps sound when the display returns to
"PRESET 1".
Note
Holding down the desired PRESET 1 to 5 button for
more than a few seconds in step 3 will replace the
previous station on the PRESET 1 to 5 button with
the station you tuned into.
Setting the Night
Light
You can change the setting of the night light on the
edge of the lid.
Set NIGHT LIGHT MODE to STANDBY, ON or
OFF. The night light operates as follows:
STANDBY: The night light turns on when the radio
is turned on, or when the lid is open.
The night light flashes when ALARM A
or B, or NAP timer sound comes on.
The night light goes out when the radio,
the sound alarm or the NAP timer sound
is turned off.
ON:
The night light is always lit.
OFF: The night light does not turn on.
Setting the Alarm
You can set two types of alarms, radio (ALARM A)
and sound (ALARM B).
The alarm will come on at the same time everyday.
Before setting the alarm, make sure to set the clock.
(See "Setting the Clock".)
Notes
·The factory setting alarm time for radio (ALARM
A) and sound (ALARM B) is "PM 12:00".
· If you quit during the alarm setting, after about 65
seconds the previous display will return.
To Set the Radio Alarm
(ALARM A)
1 Press ALARM A for a few seconds until a
beep sounds.
"
" and the hour flash on the display.
2 Press TUNE/TIME SET + or to set
the desired hour.
3 Press ALARM A.
4 Repeat steps 2 and 3 to set the minute.
A beep sounds to confirm the setting of time.
"
" appears and the preset number flashes
on the display.
5 Press TUNE/TIME SET + or to select
the station you last listened or a preset
station as "wake up station".
Each press of TUNE/TIME SET + changes
"wake up station" as follows:
PRESET -
(last station)
AM PRESET 1 to 5
FM1 PRESET 1 to 5
FM2 PRESET 1 to 5
Pressing TUNE/TIME SET changes "wake up
station" in reverse order.
6 Press ALARM A again.
Two beeps sound to confirm the setting.
To use ALARM A, set the alarm mode. (See "Setting
the Alarm Mode".)
When the alarm comes on at the preset time,
"
" flashes on the display and "wake up
station" (the station selected in step 5) comes on.
The radio is turned off automatically after about 60
minutes.
To check the alarm setting
Press ALARM A once. The display shows the preset
time.
If you press ALARM A again, the display shows
"wake up station".
After 4 seconds, the display will return to the current
time.
To Set the Sound Alarm
(ALARM B)
1 Press ALARM B for a few seconds until a
beep sounds.
"
" and the hour flash on the display.
2 Press TUNE/TIME SET + or to set
the desired hour.
3 Press ALARM B.
4 Repeat steps 2 and 3 to set the minute.
A beep sounds to confirm the setting of time.
5 Press TUNE/TIME SET + or to select
the sound number of beep (1) or melodies
(2 to 5).
1: Buzzer
2: "Peer Gynt Suite: Morning" Edvard Hagerup
Grieg
3: Green sleeves
4: "For Eliza" Ludwing van Beethoven
5: "Four Seasons: Spring" Antonio Lucio Vivaldi
When selecting the number, you can hear the
sound of the number.
6 Press ALARM B again.
Two beeps sound to confirm the setting.
To use ALARM B, set the alarm mode. (See "Setting
the Alarm Mode".)
When the alarm comes on at the preset time,
"
" and the selected sound number flash on the
display.
The sound is turned off automatically after about 60
minutes.
To check the alarm setting
Press ALARM B once. The display shows the preset
time and the selected sound number.
After 4 seconds, the display will return to the current
time
Setting the Alarm Mode
Before setting the alarm mode, be sure to set the alarm
time. (See "Setting the Alarm".)
Press ALARM MODE repeatedly until the desired
mode is selected.
Each press of ALARM MODE changes the indication
on the display as follows:
No alarm
Indication
A RADIO
A RADIO
B SOUND
B SOUND
The selected sound number is displayed with
"
".
If the same alarm time is set for both radio and sound
alarm (ALARM A and B), the radio alarm (ALARM
A) takes priority.
To Doze for a Few More
Minutes
Press SNOOZE/SLEEP OFF*.
The radio or sound turns off but will automatically
come on again after about 10 minutes. Each time you
press SNOOZE/SLEEP OFF, the snooze time
changes as follows:
10
20
30
40
50
60
The maximum length of the snooze time is 60
minutes.
The display shows the snooze time for a few seconds
and returns to show the current time. When you press
SNOOZE/SLEEP OFF after the current time
appeared, the snooze time starts from 10 minutes
again.
*The SNOOZE/SLEEP OFF button can be pushed
with the lid either open or closed.
To Stop the Alarm
Press RADIO ON·OFF to turn off the alarm.
The alarm will come on again at the same time the
next day.
To Deactivate the Alarm
Press ALARM MODE repeatedly so that "
"
and "
" go off.
Using the NAP
Timer (Count Down
Timer)
The NAP timer sounds the buzzer after a preset time
duration.
Press NAP repeatedly until the desired minutes are
displayed.
Each press changes the display as follows:
OFF
10
20
90
120
60
30
Two short beeps sound when the display returns to
"10".
"
" and the NAP time are displayed for a few
seconds.
NAP timer starts counting down the NAP time.
When selected NAP time has passed, the buzzer
comes on, and "
" on the display flash. If the
lid is closed (NIGHT LIGHT MODE: STANDBY),
the night light will flash.
The buzzer is turned off automatically after about 60
minutes.
To Stop NAP Timer
Press NAP or RADIO ON·OFF to turn off the buzzer.
To Deactive NAP Timer
Press NAP. "
" goes off in the display.
OFF
ON
NIGHT LIGHT MODE
STANDBY
A RADIO
SLEEP
FM12
AM
PM
MHz kHz
RADIO
B SOUND 12345
WAKE UP
PRESET
PRESET
OFF
RADIO
ON
BAND
SLEEP
VOLUME
BRIGHTNESS
TUNE/TIME SET
CLOCK
D.S.T./
ALARM MODE
ALARM
AB
5
4
3
2
1
NAP
ENTER
SELECT
PRESET
SNOOZE/
SLEEP OFF
PUSH OPEN
SNOOZE/SLEEP OFF
The PRESET 3 button and VOLUME have a tactile dot.
AC power cord
How to open the lid of the operating buttons
Press down the PUSH OPEN
Lift open to reveal the buttons.
You can adjust angle
of the display.
Setting the Sleep
Timer
You can enjoy falling asleep to the radio using the
built-in sleep timer that turns off the radio
automatically after a preset duration.
Press SLEEP.
The radio turns on. You can set the sleep timer to
duration of 90, 60, 30, or 15 minutes. Each press
changes the display as follows:
OFF
90
60
30
15
Two short beeps sound when the display returns to
"90".
"
" will appear in the display when the duration
time is set.
The radio will play for the time you set, then shut off.
To turn off the radio before the preset time
Press SNOOZE/SLEEP OFF or SLEEP.
To Use Both Sleep Timer and
Alarm
You can fall asleep to the radio and also be awakened
by the radio or sound alarm at the preset time.
1 Set the alarm. (See "Setting the Alarm".)
2 Set the sleep timer. (See "Setting the Sleep
Timer".)