background image
­ 1 ­
Model Name Using Similar Mechanism
D-190/191
CD Mechanism Type
CDM-2811AAC
Optical Pick-up Name
DAX-11A
SERVICE MANUAL
US Model
D-E200/E206CK/E251
Canadian Model
D-E201/E206CK
D-E200/E201/E206CK/E251
PORTABLE CD PLAYER
CD player
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength:
= 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200 mm
from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Error correction
Sony Super Strategy Cross Interleave Reed
Solomon Code
D-A conversion
1-bit quartz time-axis control
Frequency response
20 - 20,000 Hz +1/­3 dB
(measured by EIAJ CP-307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
Approx. 15 mW + Approx. 15 mW
at 16 ohms
SPECIFICATIONS
­ Continued on next page ­
General
Power requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
· Two LR6 (size AA) batteries: 3 V DC
· AC power adaptor (DC IN 4.5 V jack):
US, CND model: 120 V, 60 Hz
· Sony CPM-300P mount plate for use on car
battery: 4.5 V DC
Battery life (approx. hours) (EIAJ*)
Battery life varies depending on how the player is
used.
ESP OFF
ESP ON
Two alkaline
15
14
batteries LR6
* Measured value by the standard of EIAJ
(Electronic Industries Association of Japan).
(When the unit is used on a flat and stable place.)
Dimensions (w/h/d) (without projecting
parts and controls)
Approx. 131
× 28 × 148 mm
(5 1/4
× 1 1/9 × 5 4/5 in.)
Mass
Approx. 220 g (7.8 oz.)
Operating temperature
5°C - 35°C (41°F - 95°C)
Supplied accessories
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
D-E200
Headphones/earphones (1)
D-E201
AC power adaptor (1)
Headphones/earphones (1)
D-E251
AC power adaptor (1)
Headphones/earphones (1)
(Photo: D-E201 (Silver))
Ver 1.0 2000. 02


background image
­ 2 ­
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during
repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TABLE OF CONTENTS
1. SERVICE NOTE ................................................................ 3
2. GENERAL
Playing a CD right away! ........................................................ 4
3. DISASSEMBLY
3-1. Cabinet (Lower) Sub Assy .................................................. 6
3-2. Main Board ......................................................................... 6
3-3. MD Assy ............................................................................. 6
4. ELECTRICAL ADJUSTMENTS
4-1. Focus Bias Check ................................................................ 7
5. DIAGRAMS
5-1. IC Pin Description ............................................................... 8
5-2. Block Diagram ­CD Section­ ........................................... 10
5-3. Block Diagram ­Power Supply Section­ .......................... 13
5-4. Printed Wiring Boards ­Main Section­ ............................ 15
5-5. Schematic Diagram ­Main Section (1/2)­ ........................ 19
5-6. Schematic Diagram ­Main Section (2/2)­ ........................ 21
5-7. IC Block Diagrams ............................................................ 23
6. EXPLODED VIEWS
6-1. Cabinet (Upper) Section .................................................... 25
6-2. Cabinet (Lower) Section ................................................... 26
6-3. CD Mechanism Deck Section (CDM-2811AAC) ............. 27
7. ELECTRICAL PARTS LIST ......................................... 28
D-E206CK
AC power adaptor (1)
Headphones/earphones (1)
Car connecting pack (1)
Car battery cord (1)
Spiral tube (1)
Velcro tape (2)
Design and specifications are subject to change
without notice.
For US customers
AC power adaptor supplied is not intended to be
serviced. Should the AC power adaptor cease to
function in its intended manner, during the
warranty period, the adaptor should be returned
to your nearest Sony Service Center or Sony
Authorized Repair Center for replacement, or
after warranty period, it should be discarded.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
This Compact Disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT table is located
on the bottom exterior.


background image
­ 3 ­
D-E251
D-E200/E201/E206CK
TAP802
­ MAIN BOARD ­ (SIDE A)
SECTION 1
SERVICE NOTE
· NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
· NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
· To Check the Laser Diode and Focus Search Operation
Open the upper panel. Turn on the power without a disc while
the main board S801 (OPEN) is ON (or TAP802 is shorted). Then,
observe the objective lens and check that the following opera-
tions are performed.
1. Scatterd light of laser beams is seen.
2. Check for vertical movements (five) of the objective lens (with
movement of the PU on the inner circumference).
· Before Replacing the Optical Pick-Up Block
Please be sure to check throughly the parameters as par the "Opti-
cal Pick-Up Block Checking Procedures" (Part No.: 9-960-027-
11) issued separately before replacing the optical pick-up block.
Note and specifications required to check are given below.
· FOK output : IC601 eg pin
When checking FOK, remove the lead wire to disc motor.
When checking FOK value, remove the lead wire to disc
motor.
· RF signal P-to-P value : 0.46 - 0.66 Vp-p
· The repairing grating holder is impossible.
S801
(OPEN)
L401
S801
­ MAIN BOARD ­ (SIDE B)


background image
­ 4 ­
SECTION 2
GENERAL
This section is extracted
from instruction manual.


background image
­ 5 ­