background image
1
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM-3123EBA
Optical Pick-up Name
DAX-23E
SERVICE MANUAL
Canadian Model
UK Model
Australian Model
D-E221
AEP Model
E Model
D-E221/E223
D-E221/E223
PORTABLE CD PLAYER
CD player
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength:
= 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200 mm
from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Error correction
Sony Super Strategy Cross Interleave Reed
Solomon Code
D-A conversion
1-bit quartz time-axis control
Frequency response
20 - 20,000 Hz +1/­3 dB
(measured by EIAJ CP-307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
Approx. 12 mW + Approx. 12 mW
at 16 ohms
(Approx. 1 mW + Approx. 1 mW
at 16 ohms*)
*For the customers in France
SPECIFICATIONS
­ Continued on next page ­
General
Power requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
· Two sony NC-WMAA rechargeable
batteries (D-E223): 2.4 V DC
· Sony NH-WM2AA rechargeable
batteries (D-E223): 2.4 V DC
· Two LR6 (size AA) batteries: 3 V DC
· AC power adaptor (DC IN 4.5 V jack):
120 V, 60Hz (CND, E92, MX, TW model)
220 - 230 V, 50/60 Hz (AEP, FR, EE,
E13, G model)
230 - 240 V, 50 Hz (UK model)
240 V, 50 Hz (AUS model)
220 V, 50 Hz (AR model)
D-E221
Battery life (approx. hours) (EIAJ*)
Battery life varies depending on how the player is
used.
ESP OFF
ESP ON
Two sony alkaline
25
24
batteries LR6(SG)
* Measured value by the standard of EIAJ
(Electronic Industries Association of Japan).
(When the unit is used on a flat and stable place.)
D-E223
Battery life (approx. hours) (EIAJ*)
Battery life varies depending on how the player is
used.
ESP OFF
ESP ON
Two NC-WMAA
8
8
(charged
about 3 hours**)
NH-WM2AA
14.5
14
(charged
about 8 hours**)
Two sony alkaline
25
24
batteries LR6(SG)
* Measured value by the standard of EIAJ
(Electronic Industries Association of Japan).
(When the unit is used on a flat and stable place.)
** Charging time varies depending on how the
rechargeable battery is used.
Dimensions (w/h/d) (without projecting
parts and controls)
Approx. 130
× 26.3 × 150.5 mm
(5 1/8
× 1 1/16 × 6 in.)
Mass (excluding accessories)
Approx. 205 g (7.3 oz.)
Operating temperature
5°C - 35°C (41°F - 95°F)
(Photo: D-E221 (Silver))
Ver 1.0 2001.04
9-873-123-11
2001D0400-1
© 2001.4
Sony Corporation
Personal Audio Company
Shinagawa Tec Service Manual Production Group


background image
2
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during
repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TABLE OF CONTENTS
1. SERVICE NOTE ................................................................. 3
2. GENERAL
Playing a CD right away! ........................................................ 4
3. DISASSEMBLY
3-1. "Lid, Battery Case", Cabinet (Front) Assy .......................... 8
3-2. Lid Assy, Upper ................................................................... 8
3-3. Main Board, MD Assy ........................................................ 9
3-4. Optical Pick-up, Motor ....................................................... 9
4. ELECTRICAL ADJUSTMENTS
4-1. Focus Bias Check .............................................................. 10
5. DIAGRAMS
5-1. IC Pin Description ............................................................. 11
5-2. Block Diagram ­CD Section­ ........................................... 13
5-3. Block Diagram ­Audio Section­ ...................................... 14
5-4. Block Diagram ­Power Supply Section­ .......................... 15
5-5. Printed Wiring Board ­Main Section­ .............................. 16
5-6. Schematic Diagram ­Main Section (1/2)­ ......................... 18
5-7. Schematic Diagram ­Main Section (2/2)­ ......................... 19
5-8. IC Block Diagrams ............................................................ 20
6. EXPLODED VIEWS
6-1. Cabinet (Front) Section ..................................................... 21
6-2. Cabinet (Lower) Section ................................................... 22
6-3. CD Mechanism Deck Section (CDM-3123EBA) ............. 23
7. ELECTRICAL PARTS LIST ......................................... 24
Supplied accessories
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
D-E221
AC power adaptor (1)
Headphones/earphones (1)
AC plug adaptor (1)*
*Supplied with E33 and EA3 models
D-E223
AC power adaptor (1)
Headphones/earphones (1)
Rechargeable batteries (2)
Battery carrying case (1)
Design and specifications are subject to change
without notice.
· Abbreviation
CND : Canadian model
E92
: AC 120V area in E model
FR
: France model
EE
: East European model
E13
: AC 220 - 230V area in E model
AUS : Australian model
MX
: Mexican model
G
: German model
AR
: Argentine model
TW
: Taiwan model
D-E221/E223
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.


background image
3
D-E221/E223
1-681-329-
OPEN
S805
S801
­ MAIN BOARD ­ (SIDE B)
16
9
1
8
E223:FR MODEL
S803
S803
HOLD
OFF
ON
TAP802
­ MAIN BOARD ­ (SIDE A)
SECTION 1
SERVICE NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Precautions for Checking Emission of Laser Diode
Laser light of the equipment is focused by the object lens in the
optical pick-up so that the light focuses on the reflection surface
of the disc. Therefore, be sure to keep your eyes more then 30 cm
apart from the object lens when you check the emission of laser
diode.
Before Replacing the Optical Pick-Up Block
Please be sure to check throughly the parameters as par the "Opti-
cal Pick-Up Block Checking Procedures" (Part No.: 9-960-027-
11) issued separately before replacing the optical pick-up block.
Note and specifications required to check are given below.
· FOK output : IC601 eg pin
When checking FOK, remove the lead wire to disc motor.
· RF signal P-to-P value : 0.5 ± 0.1 Vp-p
· The repairing grating holder is impossible.
Laser Diode Checking Methods
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following two checking methods for the laser diode are
operable.
· Method:
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. With a disc not set, turn on the S801 with a screwdriver having a
thin tip as shown in Fig.1.
or TAP802 is shorted as shown in Fig.2.
Note: Do not push the detection lever strongly, or it may be bent
or damaged.
3. Press the > N button.
4. Observing the objective lens, check that the laser diode emits
light.
When the laser diode does not emit light, automatic power
control circuit or optical pick-up is faulty.
In this operation, the objective lens will move up and down 5
times along with inward motion for the focus search.
Fig. 2
Fig. 1
detection lever
detection lever
main board
S801


background image
4
D-E221/E223
SECTION 2
GENERAL
This section is extracted
from instruction manual.


background image
5
D-E221/E223