PORTABLE CD PLAYER
Personal Audio Company
Published by Sony Engineering Corporation
Ver 1.1 2002. 05
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
Compact disc digital audio system
Laser diode properties
= 780 nm
Emission duration: Continuous
Laser output: Less than 44.6
(This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
1-bit quartz time-axis control
20 - 20 000 Hz
3 dB (measured by JEITA CP-
Output (at 4.5 V input level)
Headphones (stereo minijack)
Approx.5 mW + Approx. 5 mW at 24
For the area code of the model you
purchased, check the upper left side of the
bar code on the package.
·Two LR6 (size AA) batteries: 3 V DC
·AC power adaptor (DC IN 4.5 V jack):
120 V, 60 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
Playing time varies depending on how the CD
player is used.
Figures in brackets show the playing time of
Two Sony alkaline
(produced in Japan)
*Measured value by the standard of JEITA (Japan
Electronics and Information Technology
°C - 35°C (41°F - 95°F)
Dimensions (w/h/d) (excluding
projecting parts and controls)
× 26.3 × 130.3 mm
× 1 1/16 × 5 1/4 in.)
Mass (excluding accessories)
Approx. 210 g (7.5 oz.)
Design and specifications are subject to change
Headphones (stereo minijack)
Approx.5 mW + Approx. 5 mW at 16
(Approx. 1.5 mW + Approx. 1.5 mW
*For the customers in France
For the area code of the location in which you
purchased the CD player, check the upper left side
of the bar code on the package.
AC power adaptor (1)
AC power adaptor (1)
Car battery cord (1)
Car connecting pack (1)
Velcro tape (2)
E13 : 220-230V AC area in E model.
E92 : Chilean and Peruvian model.
AEP/E13/East European/French model:
220 - 230 V, 50/60 Hz
UK model: 230 - 240 V, 50 Hz
Australian model: 240V, 50 Hz
Argentine model: 220 V, 50 Hz
Flexible Circuit Board Repairing
·Keep the temperature of the soldering iron around 270 °C dur-
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
Notes on chip component replacement
·Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
On AC poweradaptor
·Use only the AC power adaptor supplied or
recommended in "Accessories (supplied/
optional)." Do not use any other AC power
adaptor. It may cause a malfunction.
Polarity of the plug
TABLE OF CONTENTS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. SERVICING NOTE ·························································· 3
2. GENERAL ·········································································· 4
3. DISASSEMBLY ································································ 5
3-1. Battery Case Lid, Cabinet (Upper) Assy ······················· 5
3-2. Upper Lid Assy ······························································ 6
3-3. MAIN Board, MD Assy (CDM-3125ER) ····················· 6
3-4. Turn Table Motor Assy (M901) ····································· 7
3-5. Motor Assy (Sled) (M902),
Optical Pick-up (DAX-25E) ·········································· 7
4. ELECTRICAL ADJUSTMENTS ································· 8
5. DIAGRAMS ········································································ 9
5-1. Block Diagram ···························································· 10
5-2. Printed Wiring Board MAIN Board (Side A) ······· 12
5-3. Printed Wiring Board MAIN Board (Side B) ······· 13
5-4. Schematic Diagram MAIN Board (1/4) ··············· 14
5-5. Schematic Diagram MAIN Board (2/4) ··············· 15
5-6. Schematic Diagram MAIN Board (3/4) ··············· 16
5-7. Schematic Diagram MAIN Board (4/4) ··············· 17
5-8. IC Pin Function Descriptions ······································ 19
6. EXPLODED VIEWS ······················································ 26
6-1. Cabinet (Front) Section ··············································· 26
6-2. Cabinet (Lower) Section ············································· 27
6-3. Optical Pick-up Section (CDM-3125ER) ···················· 28
7. ELECTRICAL PARTS LIST ······································· 29
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
The flexible board is easily damaged and should be handled with
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
BEFORE REPLACING THE OPTICAL PICK-UP BLOCK
Please be sure to check thoroughly the parameters as par the "Optical
Pick-Up Block Checking Procedures" (Part No.: 9-960-027-11)
issued separately before replacing the optical pick-up block.
Note and specifications required to check are given below.
· FOK output: IC601 yg pin
When checking FOK, remove the lead wire to disc motor.
· RF signal P-to-P value: 0.35 to 0.75 Vp-p
LASER DIODE CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following checking method for the laser diode is operable.
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S801 as shown in Fig. 1.
3. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up. During normal
operation, the laser diode is turned ON about 2.5 seconds for
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
Fig. 1 Method to push the S801
This section is extracted
from instruction manual.
CD player (front)
1 i (headphones)
6 DISPLAY button
4 FOLDER /+ buttons
qd HOLD switch
2 OPEN button
qa DC IN 4.5 V
N >* (play, AMS/
x (stop) button
. (AMS/search) button
3 VOLUME control
5 MENU button
q; Strap holes
qf SOUND button
*The button has a tactile dot.
qg G-PRO (G-PROTECTION) switch
CD player (rear)
qh Battery compartment
CD player (inside)
This set can be disassembled in the order shown below.
3-1. Battery Case Lid, Cabinet (Upper) Assy
UPPER LID ASSY
MOTOR ASSY (SLED) (M902),
OPTICAL PICK-UP (DAX-25E)
TURN TABLE MOTOR ASSY
BATTERY CASE LID,
CABINET (UPPER) ASSY
MAIN BOARD, MD ASSY
Follow the disassembly procedure in the numerical order given.
three screws (+B 2
two screws (+B 2
cabinet (upper) assy
battery case lid