1
Ver 1.0 2004. 01
Model Name Using Similar Mechanism
CDX-F5500
CD Drive Mechanism Type
MG-611MA-186//K
Optical Pick-up Name
KSS1000E
SERVICE MANUAL
US Model
Canadian Model
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 15,000 Hz
AM
Tuning range
530 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 8 ohms
Maximum power output 52 W
× 4 (at 4 ohms)
SPECIFICATIONS
General
Outputs
Audio output terminals (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Inputs
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input or AUX IN terminal
Remote controller input terminal
Antenna input terminal
Tone controls
Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
Loudness
+8 dB at 100 Hz
+2 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
Dimensions
Approx. 178
× 50 × 178 mm
(7 1/8
× 2 × 7 1/8 in.) (w/h/d)
Mounting dimensions
Approx. 182
× 53 × 161 mm
(7 1/4
× 2 1/8 × 6 3/8 in.) (w/h/d)
Mass
Approx. 1.3 kg (2 lb. 14 oz.)
Supplied accessories
Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X141A
Design and specifications are subject to change without
notice.
· The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-877-508-01
2004A04-1
© 2004. 01
FM/AM COMPACT DISC PLAYER
CDX-F7700/F7705X
Photo: CDX-F7700
2
CDX-F7700/F7705X
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SERVICE NOTES
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
optical pick-up
semi-fixed resistor
3
CDX-F7700/F7705X
Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable
CDs)
This unit can play the following discs:
Type of discs
Label on the disc
Audio CD
MP3 files
· Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
· You cannot play a CD-R/CD-RW that is not finalized.
· You can play MP3 files recorded on CD-ROMs, CD-Rs, and
CD-RWs.
· A CD-R/CD-RW to which a session can be added can be played.
A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
· Connect the MAIN board (CN751) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SERVO BOARD
CN2
MAIN BOARD
CNP301
J-2502-076-1
4
CDX-F7700/F7705X
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 5
Connections ............................................................................. 7
2. DISASSEMBLY
2-1. Sub Panel Assy (CD) ........................................................... 9
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ....................................................................... 10
2-4. Chassis (T) Sub Assy ........................................................ 10
2-5. Roller Arm Assy ................................................................ 11
2-6. Chassis (OP) Assy ............................................................. 11
2-7. Optical Pick-up ................................................................. 12
2-8. SL Motor Assy (M902) ..................................................... 12
2-9. LE Motor Assy (M903) ..................................................... 13
2-10. Servo Board ....................................................................... 13
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 14
3-2. Block Diagram CD Section ........................................... 20
3-3. Block Diagram Main Section ........................................ 21
3-4. Block Diagram Display Section .................................... 22
3-5. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................... 23
3-6. Waveforms ......................................................................... 23
3-7. Circuit Boards Location .................................................... 23
3-8. Schematic Diagram CD Mechanism Section (1/2) ....... 24
3-9. Schematic Diagram CD Mechanism Section (2/2) ....... 25
3-10. Printed Wiring Boards CD Mechanism Section ............ 26
3-11. Schematic Diagram Main Section (1/3) ........................ 27
3-12. Schematic Diagram Main Section (2/3) ........................ 28
3-13. Schematic Diagram Main Section (3/3) ........................ 29
3-14. Printed Wiring Boards Main Section ............................ 30
3-15. Printed Wiring Board Sub Section ................................ 32
3-16. Schematic Diagram Sub Section ................................... 33
3-17. Printed Wiring Board Key Section ................................ 34
3-18. Schematic Diagram Key Section ................................... 35
3-19. IC Block Diagrams ............................................................ 36
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 38
4-2. Front Panel Section ........................................................... 39
4-3. CD Mechanism Section (1) ............................................... 40
4-4. CD Mechanism Section (2) ............................................... 41
4-5. CD Mechanism Section (3) ............................................... 42
4-6. CD Mechanism Section (4) ............................................... 43
5. ELECTRICAL PARTS LIST ......................................... 44
5
CDX-F7700/F7705X
4
Location of controls
Refer to the pages listed for details.
a DSPL (display mode change) button
13, 16, 22
b Number buttons
Radio:
To store stations/receive stored stations.
CD/MD:
(1): REP 14
(2): SHUF 15
(6): PAUSE*1 12
Sound:
(5): BBE MP*1 21
c DSO button 24
d MENU button
To display the menus.
e SOURCE (Power on/Radio/CD/MD*2/
AUX*3) button
To select the source.
f SEEK/AMS (</,) buttons
To skip tracks/fast-forward, reverse a track/
tune in stations automatically, find a station
manually/select a setting.
g SOUND button 21
h OFF (Stop/Power off) button 12, 26
i VOL (+/) buttons
To turn up or down the volume.
j EQ7 button 23
Card remote commander RM-X141A
DISC
ATT
OFF
REP
PTY
SHUF
DSPL
1
4
MODE
BBE MP
PAUSE
2
5
3
6
SOURCE
DISC +
SEEK+
SEEK
SOUND
ENTER
MENU
LIST
CAT
EQ7
DSO
VOL
DISC
SOURCE
DISC +
SEEK+
SEEK
In menu mode, the currently selectable button(s) of
these four are indicated with a " v" in the display.
(SEEK) (<):
to select
leftwards
(DISC) (M):
to select upwards
(DISC) (m):
to select downwards
(SEEK) (,):
to select
rightwards
SECTION 1
GENERAL
This section is extracted
from instruction manual.
5
k MODE button
To change operation.
l LIST (CAT)*4 button 16, 19
m DISC (ALBUM) (M/m) buttons
To receive preset stations/change the disc*5,
skip albums*6/select a menu.
n ENTER button
To enter a setting.
o ATT button 22
*1 Available only when playing back on this unit.
*2 When an optional MD unit is connected.
*3 Available only when an optional Sony portable
device is connected to AUX IN terminal of the unit.
When you connect a Sony portable device and CD/
MD unit(s) at the same time, use the AUX IN
selector.
*4 The CAT button is available only when the XM
tuner is connected.
*5 When an optional CD/MD unit is connected.
*6 Available only when an MP3 file is played.
Note
If the display disappears by pressing (OFF), it cannot
be operated with the card remote commander unless
(SOURCE)
on the unit is pressed, or a disc is inserted
to activate the unit first.
Tip
For details on how to replace the battery, see
"Replacing the lithium battery" on page 27.
Selecting a disc and album
Disc and album can be skipped using the DISC
(ALBUM) (M/m) buttons.
(With this unit)
(With optional unit)
*7 Available only when an MP3 file is played.
Skipping tracks continuously
Press once either SEEK/AMS (< or ,)
button, then press again within about 1 second
and hold.
To
Press
Skip albums*7
Album selection
M or m [once for each
album]
To continuously skip
albums, press and hold
either button.
To
Press
Skip discs
Disc selection
M or m [once for each disc]
To continuously skip discs,
press once and press again
within about 1 second (and
hold) either button.
Skip albums*7
Album selection
M or m [hold for a moment]
and release.
To continuously skip
albums, press (and hold)
within about 1 second of
first releasing the button.