background image
­ 1 ­
SERVICE MANUAL
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-363S-121
Optical Pick-up Name
KSS-520A
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
17 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than
1 % total harmonic distortion.
Other specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
99 dB
Frequency response
10 - 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance of
200 mm from the objective lens surface on the Optical
Pick-up Block.
Tuner section
FM
Tuning range
87.5 - 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
50 dB at 200 kHz
Signal-to-noise ratio
62 dB (stereo),
65 dB (mono)
Harmonic distortion at 1 kHz
0.9% (stereo),
0.5% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 - 15,000 Hz
Capture ratio
2 dB
AM
Tuning range
530 - 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.71 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 - 8 ohms
Maximum power output 45 W
× 4 (at 4 ohms)
­ Continued on next page ­
CDX-C680/C780
US Model
FM/AM COMPACT DISC PLAYER
Photo : CDX-C680
Ver 1.1 2001. 08
Sony Corporation
e Vehicle Company
Shinagawa Tec Service Manual Production Group
9-925-779-12
2001H0400-1
© 2001. 8


background image
­ 2 ­
General
Outputs
EQ output (C780)
Line outputs (3)
Power antenna relay
control lead
Power amplifier control
lead
Telephone ATT control
lead
Illumination control lead
Tone controls
Bass
±8 dB at 100 Hz
Treble
±8 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
Dimensions
Approx. 178
× 50 × 182 mm
(7 1/8
× 2 × 7 1/4 in.)
(w/h/d)
Mounting dimension
Approx. 182
× 53 × 163 mm
(7 1/4
× 2 1/8 × 6 1/2 in.)
(w/h/d)
Mass
Approx. 1.4 kg (3 lb. 1 oz.)
Supplied accessories
Parts for installation and
connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
NOTES ON CLEANING THE OBJECTIVE LENS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE
WITH MARK
! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
cotton swabs
objective lens
2-axis actuator
2-axis cover
slide base
optical pick-up
surface of objective lens
Notes:
Do not force to push the objective lens. Otherwise, the plate spring
supporting the objective lens will be bent, causing a deteriorated
RF waveform.
Never touch anything other than the objective lens. Otherwise, a
significant deterioration occurs in the RF waveform.
Apply CD lens cleaner B-4 (Part No.:J-2501-000-A) to cotton swabs
(narrow type) (Part No.:J-2501-023-A) to be lightly wet. Use a force
(about 5 g (0.18 oz)) to make the objective lens in contact with the
bottom lightly, and clean the lens by spirals as following below.
Replace the cotton swab and repeat this cleaning two or three times.
SERVICE NOTE
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
NOTES ON PICK-UP FLEXIBLE BOARD
The pick-up flexible board in this set is secured to the optical pick-
up with an adhesive tape. Once the tape is removed, an adhering
force becomes weak, and it cannot be reused.
Therefore, if the optical pick-up is replaced, replace also the pick-
up flexible board with a new one.


background image
­ 3 ­
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 4
Getting Started ......................................................................... 4
Setting the Clock ..................................................................... 5
CD Player ................................................................................ 5
Radio ....................................................................................... 8
Other Functions ....................................................................... 9
CD/MD Unit .......................................................................... 11
DSP ........................................................................................ 14
TV/Video ............................................................................... 17
Connections ........................................................................... 19
2. DISASSEMBLY
2-1. Cover ................................................................................. 21
2-2. Front Panel Assy ............................................................... 21
2-3. Mechanism Block ............................................................. 22
2-4. Sub Panel Assy .................................................................. 22
2-5. Main Board ....................................................................... 23
2-6. Heat Sink ........................................................................... 23
2-7. Chassis (T) Sub Assy ........................................................ 24
2-8. Lever Assy ......................................................................... 24
2-9. Servo Board ....................................................................... 25
2-10. Roller Assy ........................................................................ 25
2-11. Chassis (OP) (O/S) Assy ................................................... 26
2-12. Optical Pick-up Block ....................................................... 26
3. ELECTRICAL ADJUSTMENTS
Tuner Section ......................................................................... 27
4. DIAGRAMS
4-1. IC Pin Descriptions ........................................................... 30
4-2. Circuit Boards Location .................................................... 36
4-3. Block Diagram ­CD Section­ ........................................... 37
4-4. Block Diagram ­Display Section­ .................................... 39
4-5. Block Diagram ­Tuner Section­ ....................................... 41
4-6. Printed Wiring Boards ­CD Mechanism Section­ ............ 43
4-7. Schematic Diagram ­CD Mechanism Section­ ................ 47
4-8. Schematic Diagram ­Main Section­ ................................. 52
4-9. Printed Wiring Boards ­Main Section­ ............................ 57
4-10. Printed Wiring Board ­Display Section­ .......................... 62
4-11. Schematic Diagram ­Display Section­ ............................. 64
5. EXPLODED VIEWS
5-1. Chassis Section ................................................................. 71
5-2. Front Panel Section ........................................................... 72
5-3. CD Mechanism Section (1) ............................................... 73
5-4. CD Mechanism Section (2) ............................................... 74
5-5. CD Mechanism Section (3) ............................................... 75
6. ELECTRICAL PARTS LIST ........................................ 76


background image
­ 4 ­
SECTION 1
GENERAL
This section extracted from
CDX-C780's instruction manual.


background image
­ 5 ­