background image
ORDER NO.
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Lane Crawford Place, Singapore 0923
PIONEER ELECTRONIC CORPORATION 1998
RRV1959
T-ZZW APR. 1998 Printed in Japan
FOR PRECAUTION OF
REASSEMBLY AND DISASSEMBLY
This product is component of system.
For the operating instructions, refer to the service manual RRV1946 for XC-L7.
S-L7-R-LRW/XC consists of Sub Woofer(1pc) and Satellite Speaker(S-L7-R-LR/XC 2pcs).
SPEAKER SYSTEM
S-L7-R-LRW
XC
65S
This service manual is intended for qualified service technicians; it is not meant for the
casual do-it-yourselfer. Qualified technicians have the necessary test equipment and
tools, and have been trained to properly and safely repair complex products such as
those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability
of the product and may void the warranty. If you are not qualified to perform the repair
of this product properly and safely, you should not risk trying to do so and refer the
repair to a qualified service technician.
WARNING
Lead in solder in this product is listed by the California Health and Welfare agency as
a known reproductive toxicant which may cause birth defects or other reproductive
harm (California Health & Safety Code, Section 25249.5).
When servicing or handling circuit boards and other components which contain lead in
solder, avoid unprotected skin contact with the solder. Also, when soldering do not in
hale any inhale any smoke or fumes produced.
[ Sub Woofer ]
The speaker element, together with the flange, is attached to
the back board by 4 external screws. To detach it, unfasten
those screws. When attaching it, face its terminal upward.
The duct is attached to the baffle by press-fitting. To detach it,
pry it open by inserting a flat blade screwdriver into lower side.
The input terminal is attached to the back board by press-fit-
ting. To detach it, pry it open by inserting a flat blade screw-
driver into lower side.
[ Satellite Speaker ] (S-L7-R-LR)
The grille is attached to the cabinet by 4 external screws.
To detach it, unfasten those screws.
The speaker element, together with the grille is attached to the
cabinet by 2 external screws. To detach it, unfasten those
screws. When attaching it, face its terminal upper left.
The cabinet is attached to the baffle by 4 external screws.
To detach it, first remove the grille. Then remove the cabinet.
The input terminal is attached to the cabinet by 2 internal
screws. To detach it, first remove the grille and the baffle.
Then remove the input terminal.
The bushing is attached to the cabinet by press-fitting.
To detach it, first remove the grille. Then remove the bushing.


background image
2
NSP
Cabinet
FRMM-170
NSP
Label Back
FRAN-235
Connect Cord
FRDF-016
Input Terminal
FRKX-013
NSP
Acoustic Absorbent (for Bottom, side) FRMV-025
NSP
Acoustic Absorbent (for Back)
FRMV-026
NSP
Acoustic Absorbent (for Baffle)
FRMV-027
NSP
Woofer Flange
FRNK-282
NSP
Duct
FRNK-281
NSP
Label Serial
FRAN-500
Speaker (Sub Woofer)
A14ER75-51C
Screw (for Speaker)
BYC40P200FZB
NSP
Speaker System
S-L7-R-LR/XC
Speaker Cord (for Sub Woofer)
FRDF-017
Speaker Cord (for Satellite)
FRDD-042
Non-Skid Pad
FREC-024
Top Protector
FRHA-147
Bottom Protector
FRHA-148
Protection Sheet S3 (for Sub Woofer) FRHC-021
Protection Sheet S2 (for Satellite)
FRHC-022
Packing Case
FRHG-221
SCHEMATIC DIAGRAM
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
NOTES:
PARTS LIST
Mark No.
Description
Part No.
Mark No.
Description
Part No.
S-L7-R-LRW
Connect Cord (FRDF-016)
Connect Cord (FRDF-018)
For Packing
Parts List for S-L7-R-LRW/XC
Full-Range
INPUT
Red
Black
Connector
(Blue)
Woofer
INPUT
Red
Black
Connector
(White)
Connector
(Blue)
NSP
Baffle Board
PAV-SL7RLR
Grille
FRMG-134
Badge 36
FRAM-025
NSP
Grille Cloth
FRAS-080
NSP
Grille Frame
FRNK-279
NSP
Cabinet
FRNK-278
NSP
Label Back
FRAN-236
Connect Cord
FRDF-018
NSP
Bushing
FRNK-289
Speaker (Full-range)
B70AC45-56F
Screw (for Input Terminal)
PPZ30P080FZK
Screw (for Grill-Cabinet, Cabinet-Baffle) PPZ40P120FZK
Parts List for S-L7-R-LR/XC