background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2007
PDP-S58
RRV3570
SPEAKER SYSTEM
PDP-S58
XTW/E5, XTW/CN5
* Be careful in handling this product, because scratches on cabinet coating are easily
noticeable. When working on this unit, be sure to place the cabinet on a piece of
soft cloth for protection.
SERVICE PRECAUTIONS
T-ZZR APR. 2007 Printed in Japan


background image
PDP-S58
2
12
3
4
12
3
4
C
D
F
A
B
E
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
1.1 GRILLE ASSY
The Grille Assy is secured to the baffle plate with two-sided tape
and bosses. When removing the Grille Assy, if is necessary to wear
cotton gloves.
Disassembly
Remove it from the under side.
1. Insert the tip of your gloved finger into the gap between the
Grille Assy in front and the corner of the baffle plate so that the
Grille Assy is slightly lifted.
2. Insert the gloved finger to the extent of the second joint into the
gap between the cabinet and the Grille Assy.
3. Alternately and gradually lift the left and right sides of the Grille
Assy by about 5 cm, sliding gloved fingers along the cabinet. When
lifting the Grille Assy, be sure to lift the left and right sides alter-
nately, but not both sides simultaneously.
Note: Be careful not to bend the Grille Assy too far. Otherwise, it
may be damaged.
OK : Good example NG : Bad example
Reasassembly
Remove the old two-sided tape attached to the rear side of the Grille
Assy and the front side of the Baffle, and adhere new two-sided
tape. Press the bosses into the baffle plate and press the entire grille
into position. (Press the bosses from the woofer frame.)
1.2 WOOFER (Disassembly)
The woofer is secured to the baffle plate with four screws from the
outside. To remove the woofer, first remove the baffle plate. (Re-
move the baffle plate first, because the cables from the Network
Assy are short.) Remove the two packings from the side of the
woofer frame.
Reasassembly
When reassembling the woofer, place it so that its connector plate
is facing downward. Tighten the screws to the baffle, then attach
the two packings to the side of the woofer frame.
1.3 TWEETER (Disassembly)
The tweeter is secured to the baffle plate with three screws from
the outside. To remove the tweeter, first remove the baffle plate.
(Remove the baffle plate first, because the cables from the Net-
work Assy are short.)
Reasassembly
When reassembling the tweeter, place it so that its connector and
screw-hole positions align with those on the baffle plate.
Network Assy (Caution)
· When removing the Network Assy, pull it out a little at a time
from alternate sides, because it is seated tightly.
Baffle Assy (Caution)
· When reassembling the cabinet and the baffle plate, secure the
screws in the order shown in the figure below:
Grille ASSY
Baffle
Grille ASSY
Baffle
OK
NG
Network ASSY
When reassembling it,
apply a adhesive to the screws.
1
2
1
Input terminal
Baffle
5
6
7
4
3
2
1


background image
PDP-S58
3
5
678
56
7
8
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
PACKING parts List
NOTES :
· Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List.
· The
> mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
13
17
16
12
12
15
3
5
2
6
8
10
11
9
18
21
20
Inst. Manual Set
Accessory Set
Accessory Set
Screws Set
Label Serial
14
Front
Tape
Tape
Mark No.
Description
Part No.
1
Speaker Wire
SDS6049
2
Polyethylene Bag S1
SHL1439
3
Screw
BMZ50P100FTB
4
Polyethylene Bag S0
SHL1438
5
1..Bracket Assy(L-B)
SXG6018
2..Polyethylene Bag S0
SHL6077
6
1..Bracket ASSY(L-T)
SXG6019
2..Polyethylene Bag S0
SHL6077
7
1..Bracket ASSY(R-B)
SXG6020
2..Polyethylene Bag S0
SHL6077
8
1..Bracket ASSY(R-T)
SXG6021
2..Polyethylene Bag S0
SHL6077
9
Protection Pad
SHA6147
10
Spacer
SHB6052
11
Spacer
SHB6053
NSP 12
CS ASSY (R) (XTW/E5)
SMW1993
NSP 12
CS ASSY (R) (XTW/CN5)
SMW1999
13
Protection Sheet S4
SHC6063
NSP 14
CS ASSY (L) (XTW/E5)
SMW1992
NSP 14
CS ASSY (L) (XTW/CN5)
SMW1998
for XTW/E5 type
15
Packing Case
SHG6263
16
2..Polyethylene bag s2
SHL1437
17
2..Operating Instructions
SRD6081
(English, French, German,
Italian, Dutch, Spanish, Chinese)
for XTW/CN5 type
15
Packing Case
SHG6283
16
2..Polyethylene bag s2
SHL1437
17
2..Operating Instructions
SRD6082
(Chinese)
Mark No.
Description
Part No.


background image
PDP-S58
4
12
3
4
12
3
4
C
D
F
A
B
E
2.2 SPEAKER SYSTEM (CS ASSY)
Lch
is
symmetrical
to
center
line.
*This
product
appearance
shows
Rch.
Baffle Assy
GRille Assy


background image
PDP-S58
5
5
678
56
7
8
C
D
F
A
B
E
BAFFLE
CS ASSY parts List
Mark No.
Description
Part No.
1
Grille ASSY (R)
SMG6125
2
Grille ASSY (L)
SMG6127
3
Network ASSY
SWN6026
4
Gasket
SEC6099
5
Gasket
SEC6100
6
Tape
SEH6005
7
1..Input Terminal
SKX1098
NSP
2..Spring
SBH1003
NSP
2..Terminal
SKF1064
NSP
2..Terminal
SKF1065
NSP
2..Case
SNK2909
NSP
2..Lever (Black)
SNK2910
NSP
2..Lever (Red)
SNK2911
8
Speaker
A101EC65-51D
9
Speaker
FK26AP32-56H
10
Screw
BPZ35P080FTB
11
Screw
BPZ35P120FTC
12
Screw
BPZ35P140FTB
13
Screw
BPZ40P350FTC