background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2001
The speaker grille is attached to the baffle using 12 catches.
When removing, use a sharp pointed object, such as a plastic
board , or eyeleteer. Insert the point between the grille and
baffle, and gently prize the grille off. Alternatively, you can
remove the cabinet and the woofer unit, then push the grille out
from the inside.
Damage to the grille during removal may be unavoidable, but
be careful not to break the catches off of the baffle.
The woofer units are attached to the baffle by four screws from
the inside of the speaker cabinet. To remove the woofer units,
remove the four screws. When reattaching, make sure the large
connectors (attached to the speaker wire) are facing outward.
The tweeters are attached to the baffle by two screws from the
inside of the speaker cabinet. To remove the tweeter, remove
the two screws. When reattaching, make sure the larger connec-
tors are both facing inward. Also, the left cutout should be fac-
ing top left; the right cutout, bottom left.
Network ASSY is attached from the inside using screws and
adhesive. To take out, remove the screw.
RRV2556
T-ZZB NOV. 2001 Printed in Japan
PDP-S08
SPEAKER SYSTEM
XIN/E
FOR PRECAUTION OF
REASSEMBLY AND DISASSEMBLY
65S
This service manual is intended for qualified service technicians; it is not meant for the
casual do-it-yourselfer. Qualified technicians have the necessary test equipment and
tools, and have been trained to properly and safely repair complex products such as
those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability
of the product and may void the warranty. If you are not qualified to perform the repair
of this product properly and safely, you should not risk trying to do so and refer the
repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals
which are known to the state of California to cause cancer, birth defects or other
reproductive harm.
Health & Safety Code Section 25249.6 ­ Proposition 65


background image
2
PDP-S08
NSP
Cabinet
KNK1130
NSP
Baffle
KNK1131
Grille ASSY
KMG1075
NSP
Grille Cloth
KAS1084
NSP
Grille Frame
KNK1132
Network ASSY
KWN1041
NSP
Model Label
KAN1192
NSP
Packing
KEB1010
NSP
Packing
KEB1013
Cushion
KEC1096
Spacer
KEP1122
Input terminal
KKX1015
NSP
Acoustic Absorbent (
)
KMV1060
NSP
Acoustic Absorbent (
)
KMV1061
NSP
Acoustic Absorbent (
)
KMV1062
Metal renforce (
)
KNA1145
Metal renforce (
)
KNA1146
Franged anchor bolt
SBA1209
Serrated flange nut(for Cabinet)
SBN1052
Packing
SEC1566
65Label
SRW1080
NSP
Label serial(for Model label)
SRW1083
Speaker(Woofer)
A142CU61-52F
Speaker(Tweeter)
FK26AP02-69F
Screw(for Tweeter)
APZ30P080FMC
Screw(for Input Terminal)
BBZ35P140FMC
Screw(for Woofer)
BPZ40P100FMC
Screw(for Cabinet-Baffle)
BPZ40P120FZK
Screw(for NW Coil)
BPZ40P350FMC
Mark No.
Description
Part No.
For Packing
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
NOTES:
PARTS LIST
Mark No.
Description
Part No.
NSP
Accessory Set
KEA1199
NSP
Screw Set
KEA1197
Screw
CMZ50P120FZK
Bolt
SBA1210
Hexagon Wrench
SEX1021
NSP
Polyethylene Bag S1
SHL1304
Bracket ASSY SET
KEA1198
NSP
Polyethylene Bag S1
KHL1079
Bracket ASSY
KNX1134
Cushion
KEC1095
Bracket
KNA1147
NSP
Speaker Wire SET
KEA1200
Speaker Wire
KDS1017
NSP
Polyethylene Bag S1
KHL1079
Wire Clamp
KNL1085
NSP
Polyethylene Bag S1
KHL1079
Operating Instructions
KRD1017
(English,French,German,Italian,
Dutch,Spanish)
Side Pad(L)
KHA1291
Side Pad(R)
KHA1292
Top PAD
KHA1293
Bottom Pad
KHA1294
Protection Mat(for Side)
KHC1397
Protection Mat(for Center)
KHC1398
Packing Case
KHG1137
Label Serial(for Packing Case)
SRW1087
Woofer
I N
Red
Red
Black
Blue
White
White
Tweeter
1.8
µF/63V
1.0mH
SCHEMATIC DIAGRAM
Network ASSY (KWN1041)
Refer to "PRODUCT APPEARANCE".


background image
3
PDP-S08
PRODUCT APPEARANCE
12
11
9
10
14-SCREW
15
9
9
9
2x1-SCREW
8
6
6
(5)
4
12.5
21.5
1
27
2.5
28
(0.5)
4
(0.5)
(0.5)
4
4
72.5
27.5
31
628
102
67
75
74
1062
66
74
1070
15
7
5
4
3
2
1
4
PACKING
KEB1010
2
BRACKET ASS'Y
KNX1134
23
SRW1080
65 LABEL
KMV1060
ACOUSTIC ABSORBENT
CUSHION
SEC1566
METAL RINFORCE(S)
KNA1146
KMV1061
ACOUSTIC ABSORBENT
METAL RINFORCE(B)
KNA1145
PACKING
KEB1013
4
CUSHION
KEC1096
4
ACOUSTIC ABSORBENT
KMV1062
SPACER
KEP1122
NET WORK ASS'Y
KWN1041
1
2
6
4
2
2
6
22
21
20
19
18
17
16
15
SRW1083
1
14
SERIAL BARCODE LABEL
13
1
MODEL LABEL
KAN1192
6
SERRATED FLANGE NUT
SBN1052
2
12
11
10
9
2
IN-PUT TERMINAL
KKX1015
8
2
7
6
2
SPEAKER
A142CU61-52F
5
2
TW
FK26AP02-69F
4
1
GRILLE ASS'Y
KMG1075
3
1
BAFFLE
KNK1131
2
1
CABINET
KNK1130
1
6
FLANGED ANCHOR BOLT
SBA1209
No.
Part No.
Part name
Remarks
Num.
No.
Part No.
Part name
Remarks
Num.
No.
Part No.
Part name
Remarks
Num.
21
2x1-SCREW
2x4-SCREW
2x2-SCREW
20
22
22
19
13
13
18
19
18
17
16
15
14
13
Fig. 1
Fig. 2