Operating instructions
Mode d'emploi
Table top stand
Support de couverture de table
PDK-1011
2
En
Thank you for buying Pioneer's product.
Please read through the Operating Instructions to learn how
to operate your model safely and properly.
Please be advised to keep the Operating Instructions in
your place for future reference.
Contents
Cautions ................................................................... 2
Checking the Enclosed Parts .................................. 3
Assembling the Stand ............................................ 3
Attaching the Plasma display ................................ 4
Installing the Product on a Rack etc. ..................... 5
Preparing the Cables ............................................... 6
Preventing Equipment from Falling Over ............. 7
Detaching the Plasma Display from the Stand .... 7
Specifications .......................................................... 8
Dimensions Diagram .............................................. 8
Installation
¶ Consult your dealer if you encounter any difficulties
with this installation.
¶ Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
Cautions
This product is a table top stand exclusively designed for
plasma displays (PRO-1110HD / PRO-910HD) from Pioneer.
Note that it is not designed for use with any other equip-
ment. For further information, please contact the store where
you purchased your display.
Do not install or modify the product other than specified.
Do not use this stand for a plasma display other than those
designated and do not modify it or use it for other pur-
poses.
Improper installation is extremely dangerous because it
may result in it falling over or other accident.
Installation Location
· Select a location that is strong enough to support the
weight of the stand and the displays.
· Make sure the installation location is a level, flat, and
stable surface and take proper precautions when install-
ing it to make sure its weight is evenly distributed.
· Do not install it outdoors, at a hot spring, or near a beach.
· Do not install the stand where it may be subjected to
vibration or shock.
Assembling and Installation
· Assemble the stand in accordance with the assembly
instructions and securely attach all screws at the
designated locations.
There have been cases where unforeseen accidents
such as the equipment breaking or falling over
occurred after the installation of the display because
the stand was not installed as instructed.
· The display must always be installed by two or more
people to assure it is installed safely.
· Before installation, turn off the power for the display
and peripheral devices then remove the power cord
plug from the power outlet.
This product rotates 10° to the left and right.
Do not place objects within the range of rotation of this
product and the plasma display. Install this product so that
during routine use or when it is rotated, it does not protrude
from the rack or other location it has been installed. Failure
to do so could cause unforeseen accidents such as the
equipment breaking or falling over (see page 5).
Prevent accidents caused by the product falling over by
taking reliable measures to prevent it from falling over (see
Page 7).
CAUTION
This symbol refers to a hazard or unsafe practice which
can result in personal injury or property damage.
3
En
English
Checking the Enclosed Parts
Check to make sure that you have all the enclosed parts
before assembly and installation.
Table top stand x 1
Support columns x 2
Installation screws 1 (M8 x 20 mm [13/16 inch]: silver) x 2
[used to anchor the support columns and the table top stand]
Installation screws 2
(M8 x 30 mm [1-3/16 inch]:
black) x 2
Installation screws 3
(M8 x 40 mm [1-9/16 inch]:
black) x 2
Hexagonal wrench x 1
(Diagonal size: 5 mm [3/16 inch])
Operating instructions
(this document) x 1
Assembling the Stand
Note
Always assemble it on a flat table etc.
Insert the screws in the holes vertically and do not tighten
them with more force than necessary.
Assembly Procedure
1 Attaching the support columns to the stand.
Insert the head of the screw in the support column into
the hole for the support column in the stand and then
slide it downward.
Front side
Support column
attachment hole
2 Attach the support column to the stand
with the attachment screws 1 on the left
and right of the stand.
Use the enclosed hexagonal wrench to vertically tighten
it in the top hole from the rear.
3 Fully tighten two screws on left and right
of stand which have been loosely screwed
into stand.
Use the provided hexagonal wrench to fully tighten the
attachment screws which have been loosely screwed in
on the left and right sides of the stand.
Tighten the two screws
which have already
been screwed into the
stand.
4 Reconfirm that the attached screw is
firmly tightened.
Attachment screw 1
Operating instructions
Mode d'emploi
Table top stand
Support de couverture de table
PDK-1011
4
En
Attaching the Plasma Display
The weight of a 50 inch plasma display is about 40 kg
(88 lbs), that of a 43 inch model is about 30 kg (66 lbs),
they have no depth, and are unstable. Therefore, at
least two people must assemble and install them.
Note
Be sure to install it on a flat stable location.
Insert the screws in the holes vertically and do not tighten
them with more force than necessary.
Attachment Method
1 Attaching the plasma display to the stand.
Fit the stand's support columns into the slots in the center of
the bottom of the plasma display then slowly insert them
directly into the slots. Be extremely careful not to insert the
support columns of the stand into any part of the plasma
display other than the stand insertion slots. Note that doing
so might damage the plasma display panel or its ports or
result in the warping of the stand.
2 Securing the plasma display with attach-
ment screws 2.
Secure them using the enclosed hexagonal wrench.
3 Securing the plasma display with attach-
ment screws 3.
Secure them using the enclosed hexagonal wrench.
4 Attaching the speakers.
Refer to the operating instructions for the speaker for
the installation method.
Line up the column
supports with the bottom
of the plasma display as
indicated in the accompa-
nying diagram.
Attachment screw 2
Attachment
screw 3
Caution
5
En
English
Installing the Product on a Rack etc.
Be sure to observe the following precautions when moving
or installing this product with a plasma display into a rack or
other enclosure.
Precautions when moving
When moving the product more than a few meters,
first remove the speaker, then remove the plasma
display from the stand and move the speaker, plasma
display, and stand separately.
Precautions when installing in a rack
or other enclosure
When installing in a rack or other enclosure, hold the
plasma display by the handles located on the rear
and bottom of the plasma display. If you hold the
speakers, they may be damaged or twisted.
Hold the
plasma display
by its handles
and from the
bottom.
Installation precautions
Make sure that you always secure a space at least as large
as that shown in the following diagram in front of and
behind the table top stand.
But when using a rack for which the aforementioned
spaces cannot be secured, place the rack as close to a wall
as possible and give priority to securing the space in front.
If the stand protrudes from the rack, it could cause
unforeseen accidents such as the equipment break-
ing or falling over.
When rotating, take care not to allow the display
to bump into walls or surrounding objects.
Angle of rotation
10
°
10
°
Caution
Caution
Protrusion is dangerous.
Caution
Min.
10
mm
(13/32
inch)
Plasma display
Rack
Table top stand
Min.
30
mm
(1-3/16
inch)
Back
Depth
of
the
rack
430
mm
(16-15/16
inch)
or
more
recommended
Front