background image
1
www.pioneerelectronics.com
IMPORTANT:
· The serial number for this equipment is located on the side
of the packing case. Please write this serial number on the
warranty page and keep it in a secure area for future
reference.
BEFORE USE
·
Thank you for buying this Pioneer product.
·
Please read through this operating guide before using your
speaker system to optimize performance.
FRONT / CENTER / SURROUND SPEAKERS
In order to prevent damage to the speaker system resulting
from input overload, please observe the following precautions:
·
When connecting or disconnecting cables, be sure amplifier
power is OFF.
·
Do not use excessive amplifier volume if using a tone control
to emphasize high or low frequencies.
INSTALLATION PRECAUTIONS
FRONT / CENTER / SURROUND SPEAKERS
·
Do not install these units near a stove or other heating
appliance, or put them in a place exposed to the sun. Such
locations may cause the cabinet to change color and the
speaker system to break down.
·
The front, center and surround speakers supplied with this
system are magnetically shielded. However, placing them
extremely close to a television may result in color distortion on
the screen. If this happens, move the speakers a little further
away and switch off the television for 15 to 30 minutes.
SUBWOOFER
·
Do not place anything on top of the cabinet.
·
Do not spill liquid on the cabinet.
·
Place the subwoofer at least 8 inches from any wall or
curtain in order to avoid heat build-up.
·
The subwoofer is not magnetically shielded and so should
not be placed near a TV or monitor. Magnetic storage media
(such as floppy discs and tape or video cassettes) should
also not be kept close to the subwoofer.
S-FCR4700
OPERATING GUIDE
S-FCR3700
S-W3700
SPEAKER SYSTEM
· Speaker stand bases
x 4 (S-FCR4700)
x 2 (S-FCR3700)
· Screws (for bases)
· Screws
(for Spealer stand)
· Speaker stands
x 12 (S-FCR4700)
x 2 (S-FCR3700)
x 2 (S-FCR3700)
x 6 (S-FCR3700)
· Front speakers x 2
· Non-skid pads (Large)
· Non-skid pads (Small)
x 4
(For subwoofer)
x 8 (S-FCR3700)
(For speaker stand bases)
x 16 (S-FCR4700)
(For speaker stand bases)
x 4 (S-FCR4700)
(For center speaker)
x 12 (S-FCR3700)
(For center and
surround speakers)
· Surround speakers x 2
(S-FCR3700)
· Center speaker
· Surround speakers x 2
(S-FCR4700)
· Subwoofer
· Speaker cords x 6
Front left (White)
Front right (Red)
Surround left (Blue)
Surround right (Grey)
Center (Green)
Subwoofer (Purple)
· Operating guide
WHAT'S IN THE BOX


background image
2
www.pioneerelectronics.com
CAUTION:
· Do not connect this speaker to any amplifier other than the
one supplied with this system. Connection to any other
amplifier may result in a malfunction or a fire.
· Do not attach the subwoofer, front and surround speakers
to the wall or ceiling. They may fall off and cause injury (S-
FCR4700 only).
· Do not attach the subwoofer and front speakers to the wall
or ceiling. They may fall off and cause injury (S-FCR3700
only).
WARNING:
Handling the cord on this product or cords associated with
accessories sold with the product will expose you to
chemicals listed on proposition 65 known to the State of
California and other governmental entities to cause cancer
and birth defect or other reproductive harm.
Wash hands after handling
CONNECTING YOUR SYSTEM
IMPORTANT:
Make sure all equipment is turned off before making any
connections.
FRONT / CENTER / SURROUND / SUBWOOFER
SPEAKERS
Correct wiring of your loudspeakers is essential for achieving
the best sound quality. Be careful to ensure proper polarity of
connection.
Twist and pull off the protective shields on each wire.
Connect to the speaker terminals on the rear of the
receiver.
To connect, insert the colored wire into the matching positive
(colored) terminal and the other wire into the negative (black)
terminal as shown below.
Note that the color-coded tabs are as follows:
· Red : Front right (R)
· Purple : Subwoofer
· White : Front left (L)
· Grey : Surround right (R)
· Green : Center speaker
· Blue : Surround left (L)
Connect the speaker cords to the input terminals at the
rear of speaker.
Match the colored wire with the color-coded label (above the
tabs), then insert the colored wire into the red (+) tab and the
other wire with the black (­) tab.
red (+)
black (­)
Colored marker
PLACEMENT AND FINE TUNING
SUBWOOFER
Sound spreads in all directions in the very low frequency range.
Human hearing cannot easily detect the source of very low
frequencies. Be sure to provide a space of at least 8 inches
(20 cm) between the rear of the subwoofer and the nearest wall.
FRONT SPEAKERS
For best results the loudspeakers should be separated a distance
approximately equal to the listening distance. Angling the
loudspeakers inward towards the listener will improve the image
stability for non-central listeners. Close proximity to a side or rear
wall will enhance the midbass performance, although too close
(particularly a corner location) and the bass may be unnaturally
high and image performance may be degraded.
CENTER SPEAKER
The loudspeaker should be positioned below the TV. For best
results align the front of the loudspeaker with the front of the TV.
If the loudspeaker is placed under the TV and very close to the
floor, then tilting upwards may be beneficial.
When installing the center speaker on top of the TV, be sure to
secure it with tape or some other suitable means. Otherwise, the
speaker may fall from the TV due to external shocks such as
earthquakes, endangering those nearby or damaging the speaker.
SURROUND SPEAKERS
For best results the loudspeaker should be positioned near ear
level (S-FCR3700 only).
STANDARD SURROUND SETUP
This is a standard multichannel surround soundspeaker setup
for optimal 5.1 channel home theater sound.
Front left
Surround
left
Listening position
Center
Subwoofer
Front right
Surround
right


background image
3
www.pioneerelectronics.com
Assembling the speaker stands and securing your front
and surround (S-FCR4700 only) speakers
Attach the speaker stand bases to the stems using the screws
provided.
Once you have aligned the stem and base, secure with the
small screws at the points shown below. Note that the speaker
should face in the direction of the base of the isosceles triangle
(outlined below).
Rear
Front
Secure each of the front and surround (S-FCR4700 only)
speakers using the metal catch provided.
Screw two picture hooks or similar into the wall behind the
speaker. Pass a chain or cord around the hooks and through
the metal catch so that the speaker is stabilized (make sure to
test that it supports the weight of the speaker).
After installing, make sure the speaker is securely fixed.
Chain or cord
Metal catch
CAUTION:
· The metal catch is not a mounting fixture, and the speaker
should not be hung directly from the wall using this catch.
Always use a chain or cord when stabilizing the speaker.
· Pioneer disclaims all responsibility for any losses or
damage resulting from improper assembly, installation,
insufficient strength of the installation materials, misuse, or
natural disasters.
NON-SKID PADS
Attach the small non-skid pads to the base of the surround (S-
FCR3700 only) and center speakers. The large non-skid pads
are for the front and surround (S-FCR4700 only) speakers, and
the subwoofer (as shown).
Use the adhesive side of the pads to attach them to the base of
each speaker and the subwoofer.
If you choose to use speaker stands with the surround speakers,
attach the non-skid pads to the stand bases instead of to the
underside of the speakers (S-FCR3700 only).
Small non-skid pads
Surround speakers
(S-FCR3700 only)
Center speaker
speaker stand
(S-FCR3700 only)
Large non-skid pads
Front and Surround
(S-FCR4700 only) speakers
Subwoofe
Optionally, attach the surround speakers to
the speaker stands (S-FCR3700 only) .
For each speaker,line up the spurs on the stand with the holes
on the back of the speaker and insert, then secure the speaker
to the stand with the screw provided.
WALL MOUNTING THE SURROUND
(S-FCR3700 ONLY) AND CENTER SPEAKERS
The surround (S-FCR3700 only) and center speakers have
mounting holes which can be used to mount the speaker on the
wall.
5 mm
10 mm
5 mm to 7 mm
Before mounting (see above), keep in mind the following points:
¶ Remember that the speaker system is heavy and that its
weight could cause the screws to work loose, or the wall
material to fail to support it, resulting in the speaker falling.
Make sure that the wall you intend to mount the speakers on
is strong enough to support them. Do not mount on plywood
or soft surface walls.
¶ Mounting screws are not supplied. Use screws suitable for
the wall material and support the weight of the speaker.
CAUTION:
· If you are unsure of the qualities and strength of the walls,
consult a professional for advice.
· Pioneer is not responsible for any accidents or damage
that result from improper installation.


background image
4
www.pioneerelectronics.com
TROUBLESHOOTING
SYMPTOM
1. No sound
2. Sound is distorted
PROBABLE CAUSE
· Bad speaker wire or connection
· Receiver is off
·Volume control is at zero
· Extreme signal condition
REMEDY
· Connect correctly or replace wire
·Turn on receiver
· Slowly turn up volume
·Turn down the amplifier's output level
(volume, bass control, bass boost) to
lower the level.
SPECIFICATIONS
FRONT SPEAKERS
Enclosure .................................... Closed-box floorstanding type
(magnetically shielded)
System .................................................................. 2-way system
Speakers:
Woofer ................................................. 7.7 cm cone type × 2
Tweeter ............................................ 2.6 cm semi-dome type
Nominal impedance .............................................................. 8
Frequency range ............................................... 70 Hz to 20 kHz
Dimensions ............. 260 mm (W) × 1095 mm (H) × 260 mm (D)
10-1/4 in. (W) × 43-1/8 in. (H) × 10-1/4 in. (D)
Weight .............................................................. 4.2 kg / 9 lb. 4 oz
SURROUND SPEAKERS (S-FCR3700)
Enclosure .......................................... Closed-box bookshelf type
(magnetically shielded)
System ...................................................... 7.7 cm 1-way system
Speakers .......................................................... 7.7 cm cone type
Nominal impedance .............................................................. 8
Frequency range ............................................... 80 Hz to 20 kHz
Dimensions ................. 100 mm (W) × 136 mm (H) × 80 mm (D)
3-15/16 in. (W) × 5-3/8 in. (H) × 3-1/8 in. (D)
Weight ............................................................ 0.55 kg / 1 lb. 3 oz
SURROUND SPEAKERS (S-FCR4700)
Enclosure .................................... Closed-box floorstanding type
(magnetically shielded)
System .................................................................. 2-way system
Speakers:
Woofer ................................................. 7.7 cm cone type × 2
Tweeter ............................................ 2.6 cm semi-dome type
Nominal impedance .............................................................. 8
Frequency range ............................................... 70 Hz to 20 kHz
Dimensions ............. 260 mm (W) × 1095 mm (H) × 260 mm (D)
10-1/4 in. (W) × 43-1/8 in. (H) × 10-1/4 in. (D)
Weight .............................................................. 4.2 kg / 9 lb. 4 oz
CENTER SPEAKER
Enclosure .......................................... Closed-box bookshelf type
(magnetically shielded)
System ...................................................... 7.7 cm 1-way system
Speakers .......................................................... 7.7 cm cone type
Nominal impedance .............................................................. 8
Frequency range ............................................... 75 Hz to 20 kHz
Dimensions ................... 270 mm (W) × 96 mm (H) × 90 mm (D)
10-5/8 in. (W) × 3-3/4 in. (H) × 3-9/16 in. (D)
Weight .......................................................... 0.78 kg / 1 lb. 12 oz
SUBWOOFER
Enclosure .................................................. Bass-reflex floor type
System ....................................................... 16 cm 1-way system
Speaker ............................................................. 16 cm cone type
Nominal impedance .............................................................. 8
Frequency range .............................................. 30 Hz to 2.0 kHz
Dimensions ................ 190 mm (W) x 360 mm (H) x 320 mm (D)
7-1/2 in. (W) × 14-3/16 in. (H) × 12-5/8 in. (D)
Weight ............................................................ 4.0 kg / 8 lb. 13 oz
ACCESSORIES
Speaker cords ........................................................................... 6
Non-skid pads (For subwoofer) ................................................. 4
Non-skid pads (For speaker stand bases)
(S-FCR3700) ...................................................................... 8
(S-FCR4700) .................................................................... 16
Non-skid pads
(For center and surround speakers) (S-FCR3700) ........... 12
(For center speaker) (S-FCR4700) ..................................... 4
Speaker stands (For surround speakers) (S-FCR3700) ........... 2
Screws (For speaker stands) (S-FCR3700) .............................. 2
Note: Specifications and design subject to possible
modification without notice due to improvements.
Published by Pioneer Corporation.
Copyright © 2006 Pioneer Corporation.
All rights reserved.
CABINET MAINTENANCE
Use a polishing cloth or dry cloth to wipe off dust and dirt.
When the cabinet is very dirty, clean with a soft cloth dipped in
some neutral cleanser diluted five or six times with water, and
then wipe again with a dry cloth. Do not use furniture wax or
cleaners.
Never use thinners, benzine, insecticide sprays and other
chemicals on or near the cabinets, since these will corrode the
surfaces.


background image
5
www.pioneerelectronics.com
Selecting fine audio equipment such as the unit you've just
purchased is only the start of your musical enjoyment. Now it's
time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic
Industries Association's Consumer Electronics Group want you
to get the most out of your equipment by playing it at a safe level.
One that lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly, without
affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort
level" adapts to higher volumes of sound. So what sounds
"normal" can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE
your hearing adapts.
To establish a safe level:
· Start your volume control at a low setting.
· Slowly increase the sound until you can hear it comfortably
andclearly, and without distortion.
Once you have established a comfortable sound level:
· Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing
damage or loss in the future. After all, we want you listening for
a lifetime.
We Want You Listening ForA Lifetime
Used wisely, your new sound equipment will provide a lifetime
of fun and enjoyment. Since hearing damage from loud noise is
often undetectable until it is too late, this manufacturer and the
Electronic Industries Association's Consumer Electronics Group
recommend you avoid prolonged exposure to excessive noise.
This list of sound levels is included for your protection.
Information courtesy of the Deafness Research Foundation.
90
Subway, motorcycle, truck traffic, lawn mower
100
Garbage truck, chain saw, pneumatic drill
120
Rock band concert in front of speakers, thunderclap
140
Gunshot blast, jet plane
180
Rocket launching pad
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
30
Quiet library, soft whispers
40
Living room, refrigerator, bedroom away from traffic
50
Light traffic, normal conversation, quiet office
60
Air conditioner at 20 feet, sewing machine
70
Vacuum cleaner, hair dryer, noisy restaurant
80
Average city traffic, garbage disposals, alarm clock
at two feet.
Decibel
Level
Example