background image
1
RECEIVER
­
+
+
+
­
+
­
­
­
+
BASS
OFF
SOUND
TONE
MPX
AUTO
ROOM
SETUP
TEST
TONE
SYSTEM
SETUP
CH LEVEL
TUNING
STATION
FM/AM TAPE/VCR
TV
CLASS
DIGITAL
INPUT SELECTOR
STB
DVD/DVR
TUNER
EDIT
SLEEP
STATUS
DIMMER
STANDBY/ON
MUTE
SURROUND
ENTER
VOLUME
STEREO
TREBLE
Check that you have all the
accessories.
Remote control
FM wire antenna
AM loop antenna
Batteries (x2)
* Before placing the speakers,
please refer to the speaker
manual for detailed assembly
instructions. Also check the
speaker manual for a complete
list of supplied accessories.
You should also have:
· Speakers*
· Subwoofer
· Non-skid pads (1x12)
· Speaker cord (x6)
·
AC adaptor
·
Transmitter
·
Power cord
·
RCA stereo cord
·
Safety precautions (1 sheet)
Insert the supplied
batteries following the
markings inside the
battery compartment
to align them correctly.
· Operating instructions
· Warranty card
5
DIGITAL
OUT
+
­
+
­
DIGITAL INPUT
(COAXIAL)
DVD/DVR
OUT
RL
IN
TV IN
AUDIO
AUDIO
OUT
VIDEO
IN
VIDEO
OUT
R
L
Connect the receiver to your DVD
player/ recorder.
1
Use a coaxial digital cord (not supplied) to connect the digital
output of your DVD player/ recorder to the DIGITAL INPUT
(COAXIAL) DVD/DVR jack.
2
Use a red/white stereo audio cord (not supplied) to connect the
AUDIO TV IN jack on the receiver to the audio output on your
TV.* This will allow you to listen to your TV through this
speaker system.
* Note that you must also connect the DVD player/ recorder's
video output to your TV's video input to watch a DVD video
(video cable is not supplied).
DVD player/ recorder
Receiver
TV
ANTENNA
FM
UNBAL
75
AM
LOOP
AM loop
antenna
FM wire antenna
3/8 in.
(10mm)
4 Connect antennas
1
Connect the FM wire antenna and fully extend along a
window frame or another suitable place that gives good
reception.
2
To connect the AM loop antenna, twist the exposed wire
strands together and insert into the terminal, then snap
the connector shut as shown below.
Receiver
6
POWER
OFF
ON
TUNED
VIDEO 1
STANDBY/ON
STANDBY/ON
STANDBY/ON
STANDBY/ON
VIDEO SELECT
POWER
OFF
ON
Plug the receiver, wireless speaker,
DVD player/ recorder and TV into a
convenient AC outlet.
1 Press STANDBY/ON to switch on the receiver.
3
2
Switch on your DVD player/ recorder and TV, and set the TV to
the correct video input.
Press to switch the wireless speaker on.
Receiver
Wireless speaker
DVD player/ recorder
TV
7
+
­
VOLUME
AUTO
SURROUND
STEREO
FM/AM TAPE/VCR
TV
DIGITAL
INPUT SELECTOR
STB
DVD/DVR
After switching on, make any
necessary settings required by the
DVD player/ recorder, then you're
ready to start enjoying your home
theater system.
Refer to the receiver's operating instructions for a detailed
explanation of this system's surround sound features.
3
For the best surround sound, set up your
speakers like this. The front left and right
speakers should be about 6­9 feet apart.
Connect each speaker to the receiver using the
supplied speaker wires.
To connect, insert the colored wire into the matching colored
(
+) tab and the other wire into the black (­) tab as shown below.
Note that the color-coded tabs are as follows:
·
Red : Front right speaker
·
Purple : Subwoofer
·
White : Front left speaker
·
Grey : Surround right speaker
·
Green : Center speaker
·
Blue : Surround left speaker
SPEAKERS
WIRELESS
R
L
OUT
+
­
+
­
RL
R
L
CENTER
SUB
WOOFER
FRONT
SURROUND
Listening position
Front left
Front right
Surround left
Surround right
Center
Subwoofer
Receiver
R
WIRELESS
IN
L
Transmitter
Wireless speaker
· Please also read the Operating
Instructions included with the
wireless speaker.
HTP-4600 Quick Start Guide
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
2
SPEAKERS
WIRELESS
R
L
OUT
+
­
+
­
RL
R
L
CENTER
SUB
WOOFER
FRONT
SURROUND
WIRELESS
R
L
OUT
R
WIRELESS
IN
L
To power outlet
AC
adaptor
Receiver
Transmitter
Connect wireless speaker transmitter.
1
2
Use the supplied 2-pin RCA cord to connect the WIRELESS
(IN) jack on the transmitter to the WIRELESS (OUT) jack on
the rear panel of the receiver.
Connect to a power outlet using the supplied AC adaptor.
HTP4600.p65
05.1.17, 5:32 PM
1

background image
Setting Up Your HTP-4600 Home Theater System At-a-Glance
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
AUDIO
OUT
VIDEO
IN
WIRELESS
R
L
OUT
AUDIO
DIGITAL INPUT
(COAXIAL)
DVD/DVR
TV IN
SPEAKERS
+
­
+
­
RL
R
L
CENTER
SUB
WOOFER
FRONT
SURROUND
Front L.
Surround L.
Surround R.
Front R.
Center
Subwoofer
Receiver
+
­
Refer to the following diagram when making system connections for a full surround sound
setup. Note that the TV, DVD player/ recorder and some accessories are not included. Refer to
the reverse side of this sheet to check what's supplied with the HTP-4600.
DVD player/ recorder
COAXIAL OUT
VIDEO OUT
Not supplied
Not supplied
Not supplied
Transmitter
R
WIRELESS
IN
L
Wireless speaker
AC IN
POWER
OFF
ON
TUNED
To power outlet
Surround speakers
Center speaker
Stick the self-adhesive non-skid pads to the underside of each
speaker. Use four pads per speaker. Make sure to use a stable
surface when doing this, and lay the speakers flat on their side.
<ARE7377-A>
HTP4600.p65
05.1.17, 5:32 PM
2