background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2003
DVR-3100-S
RRV2843
DVD RECORDER
DVR-3100-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
Power Requirement
Region No.
Serial No.
Please confirm 3rd & 4th
alphabetical letters.
DVR-3100-S
WY
AC220-240V
2
&&TT######$$
DVR-3100-S
WYXU
AC220-240V
2
&&PG######$$
DVR-3100-S
WVXU
AC220-240V
2
&&PG######$$
÷ When servicing this model, some service procedures may reset the settings that customer
set (*) to the factory default settings. Make sure to explain this to the customer.
(*) : Initial Setup (Clock Setting, Remote Control Set, Channel settings, Video Out settings,
Audio In settings, Audio Out settings, Language settings)
Refer to the chapter 12 of the Operating Instructions for more details.
For details, refer to "Important symbols for good services" .
T-ZZV OCT. 2003 printed in Japan


background image
DVR-3100-S
2
1234
123
4
C
D
F
A
B
E
SAFETY INFORMATION
WARNING!
DEVICE INCLUDES LASER DIODE WHICH
EMITS INVISIBLE INFRARED RADIATION
WHICH IS DANGEROUS TO EYES. THERE IS
A WARNING SIGN ACCORDING TO PICTURE
1 INSIDE THE DEVICE CLOSE TO THE LASER
DIODE.
LASER
Picture 1
Warning sign for
laser radiation
LASER DIODE CHARACTERISTICS
MAXIMUM OUTPUT POWER : 50 mw
WAVELENGTH : 658 nm
1. The ON/OFF(ON:low level,OFF:high level) status of the
CLAMP signals for detecting the loading state are detected
by the drive CPUs, and the design prevents laser diode
oscillation when the CLAMP signal turns OFF.
In normal operation, if no disc is clamped, the laser diode
oscillation is disabled.
However, the interlock does not always operate in the test
mode.
2. When the cover is opened, close viewing of the objective
lens with the naked eye will cause exposure to a Class 3A
laser beam.
Additional Laser Caution
IMPORTANT
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1.
SERVICING OPERATION OF THE APPARATUS
SHOULD BE DONE BY A SPECIALLY
INSTRUCTED PERSON.
LABEL CHECK
DRW2179


background image
DVR-3100-S
3
5
678
56
7
8
C
D
F
A
B
E
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.


background image
DVR-3100-S
4
1234
123
4
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 PACKING ................................................................................................................................................... 8
2.2 EXTERIOR............................................................................................................................................... 10
2.3 FRONT PANEL ........................................................................................................................................ 12
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................14
3.1 BLOCK DIAGRAM ................................................................................................................................... 14
3.1.1 OVERALL BLOCK DIAGRAM............................................................................................................... 14
3.1.2 TUJB ASSY BLOCK DIAGRAM............................................................................................................ 16
3.1.3 MAIN ASSY BLOCK DIAGRAM............................................................................................................ 18
3.1.4 POWER BLOCK DIAGRAM.................................................................................................................. 20
3.2 ATAB ASSY and OVERALL WIRING DIAGRAM...................................................................................... 22
3.3 TUJB(1/3) ASSY ...................................................................................................................................... 24
3.4 TUJB ASSY(2/3) ...................................................................................................................................... 26
3.5 TUJB ASSY(3/3) ...................................................................................................................................... 28
3.6 FRJB and DVJB ASSYS .......................................................................................................................... 29
3.7 MAIN ASSY(1/5) ...................................................................................................................................... 30
3.8 MAIN ASSY(2/5) ...................................................................................................................................... 32
3.9 MAIN ASSY(3/5) ...................................................................................................................................... 34
3.10 MAIN ASSY(4/5) .................................................................................................................................... 36
3.11 MAIN ASSY(5/5) .................................................................................................................................... 38
3.12 MHLP ASSY .......................................................................................................................................... 40
3.13 FLKY ASSY ........................................................................................................................................... 42
3.14 SCRB ASSY .......................................................................................................................................... 44
3.15 POWER SUPPLY UNIT.......................................................................................................................... 46
3.16 WAVE FORMS ....................................................................................................................................... 47
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 50
4.1 ATAB ASSY .............................................................................................................................................. 50
4.2 TUMJ ASSY ............................................................................................................................................. 52
4.3 MAIN and MHLP ASYS ........................................................................................................................... 56
4.4 POWER SUPPLY UNIT............................................................................................................................ 60
4.5 FRJB and DVJB ASSYS .......................................................................................................................... 62
4.6 FLKY ASSY ............................................................................................................................................. 63
4.7 SCRB ASSY ............................................................................................................................................ 64
5. PCB PARTS LIST ........................................................................................................................................... 66
6. ADJUSTMENT ............................................................................................................................................... 71
6.1 TUJB ASSY ADJUSTMENT .................................................................................................................... 71
6.2 MAIN ASSY ADJUSTMENT .................................................................................................................... 72
7. GENERAL INFORMATION ............................................................................................................................. 73
7.1 DIAGNOSIS ............................................................................................................................................. 73
7.1.1 CPRM ID NUMBER AND DATA SETTING............................................................................................ 73
7.1.2 SERVICE MODE................................................................................................................................... 75
7.1.3 DV DEBUG MODE................................................................................................................................ 83
7.1.4 ERROR RATE MEASUREMENT .......................................................................................................... 86
7.1.5 VIDEO ADJUSTMENT FOR SPECIFIC AREA ..................................................................................... 88
7.1.6 SETUP SEQUENCE ............................................................................................................................. 92
7.1.7 DISASSEMBLY ..................................................................................................................................... 93
7.2 IC ............................................................................................................................................................. 96
7.3 OUTLINE OF THE PRODUCT............................................................................................................... 127
7.4 DISC/CONTENT FORMAT .................................................................................................................... 130
7.5 CLEANING............................................................................................................................................. 132
8. PANEL FACILITIES ...................................................................................................................................... 133


background image
DVR-3100-S
5
5
678
56
7
8
C
D
F
A
B
E
1. SPECIFICATIONS
VHF (low)
VHF (high)
Hyper
UHF
VHF (low)
VHF (high)
Hyper
UHF
STEREO
B/G - A2
I - NICAM
L - NICAM
B/G - NICAM
D/K - NICAM
Channel
E2 - E4
X - Z
E5 - E12
S1 - S20
M1 - M10
U1 - U10
S21 - S41
E21 - E69
Frequency
47 - 89 MHz
104 - 300 MHz
302 - 470 MHz
470 - 862 MHz
Channel
A - C
X - Z
D - J
11, 13
S1 - S20
S21 - S41
E21 - E69
Frequency
44 - 89 MHz
104 - 300 MHz
302 - 470 MHz
470 - 862 MHz
PAL B/G
PAL I
Channel
2 - 4
5 - 10
B - Q
S21 - S41
21 - 69
Frequency
49 - 65 MHz
104 - 300 MHz
300 - 470 MHz
470 - 862 MHz
Channel
R1 - R5
R6 - R12
S1 - S20
S21 - S41
E21 - E69
Frequency
49 - 94 MHz
104 - 300 MHz
302 - 470 MHz
470 - 862 MHz
SECAM L
SECAM D/K
General
System...........................DVD-Video, DVD-R/RW,Video-CD,
CD, CD-R/RW (WMA, MP3, JPEG. CD-DA)
Power requirements.............................220­240 V, 50/60 Hz
Power consumption.......................................................35 W
Power consumption in standby mode..............0.7 W (FL off)
Weight..........................................................................4.4 kg
Dimensions...........................420 (W) x 69 (H) x 341 (D) mm
Operating temperature....................................+5
°C to +35°C
Operating humidity..................5% to 85% (no condensation)
TV system..............PAL/SECAM/NTSC (external input only)
Recording
Recording format................................DVD Video Recording
DVD-VIDEO
Recordable discs
DVD-RW (DVD Re-recordable disc)
DVD-R (DVD Recordable disc)
Video recording format
Sampling frequency.................................................13.5MHz
Compression format....................................................MPEG
Audio recording format
Sampling frequency.....................................................48kHz
Compression format..................Dolby Digital or Linear PCM
(uncompressed)
Recording time
Fine (FINE).....................................................Approx. 1 hour
Standard Play (SP).......................................Approx. 2 hours
Long Play (LP)..............................................Approx. 4 hours
Extended Play (EP).......................................Approx. 6 hours
Manual Mode (MN)...................................Approx. 1­6 hours
Tuner
Receivable channels
Timer
Programs..............................................1 month/32 programs
Clock..............................Quartz lock (24-hour digital display)
Power off memory.........Approx. 5 years (after manufacture)
Input/Output
VHF/UHF antenna input/output terminal...........VHF/UHF set
75
(IEC connector)
Video input......................................Input 1, 3 (rear), 2 (front)
Input level.........................................................1 Vp-p (75
)
Jacks............................................. AV connector 2 (Input 1),
RCA jack (Input 2,3)
Video output..........................................................Output 1,2
Output level .....................................................1 Vp-p (75
)
Jacks...............................................AV connector (Output 1)
RCA jack (Output 2)
S-Video input..................................Input 1, 3 (rear), 2 (front)
Y (luminance) - Input level................................1 Vp-p (75
)
C (colour) - Input level...............................286 mVp-p (75
)
Jacks..............................................AV connector 2 (Input 1),
4 pin mini DIN (Input 2,3)
S-Video output.......................................................Output 1,2
Y (luminance) - Output level.............................1 Vp-p (75
)
C (colour) - Output level............................286 mVp-p (75
)
Jacks...........................................AV connector 1 (Output 1),
4 pin mini DIN (Output 2)
Audio input...............................Input 1, 3 (rear), 2 (front) L/R
Input level
During audio input......................................................2V rms
(Input impedance: more than 22 k
)
Jacks..............................................AV connector 2 (Input 1),
RCA jacks (Inputs 2,3)