background image
ORDER NO.
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880
PIONEER ELECTRONIC CORPORATION 1998
RRV1985
DVD PLAYER
DV-K101
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 3
3. SCHEMATIC DIAGRAM ..................................... 10
4. PCB CONNECTION DIAGRAM .......................... 23
5. PCB PARTS LIST ............................................... 33
6. ADJUSTMENT .................................................... 38
CONTENTS
7. GENERAL INFORMATION ................................ 46
7.1 IC ................................................................. 46
7.2 DISASSEMBLY ........................................... 48
7.3 BLOCK DIAGRAM ....................................... 49
8. PANEL FACILITIES AND SPECIFICATIONS .... 50
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
T ­ ZZE AUG. 1998 Printed in Japan
e
p
y
T
l
e
d
o
M
t
n
e
m
e
r
i
u
q
e
R
r
e
w
o
Ps
k
r
a
m
e
R
l
a
n
o
i
g
e
R
s
e
d
o
c
n
o
i
t
c
i
r
t
s
e
r
)
r
e
b
m
u
n
n
o
i
g
e
r
(
1
0
1
K
-
V
D
C
KO
V
0
2
1
C
A
1
· Refer to the service guide RRV1896 for DV-505.
IC information is described in the service guide.
D DVDPLAYER DV-K101
1
2
3
4
5
6
7
8
9
0
+10
PLAYBACK ONE-TOUCH
KARAOKE
CONTROL
KARAOKE
MODE
ON/OFF
OPEN/CLOSE
STANDBY
MIN
MAX
MIN
MAX
MIN
MAX
MIC CONTROL
PREVIOUS
NEXT
RETURN
SELECT
STOP
PLAY
PAUSE
STANDBY/ ON
LOW CONTROL HIGH
KEY
ECHO
MIC 1
MIC 2
MIC 1
MIC 2
0
41
¡ ¢
78
3
Î
DIGITAL VIDEO
MC


background image
2
DV-K101
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Cod e Section 25249.6 ­ Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse)
and/or
(slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide)
et/ou
(fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident
from visual
inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or
additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test


background image
DV-K101
3
2.1 PACKING
1
Power Cord
ADG1126
2
Video Cord (L=1.5m)
VDE1048
3
Audio Cord (L=1.5m)
VDE1033
NSP
4
Dry Cell Battery (R6P, AA)
VEM-013
5
Operating Instructions
VRB1196
(English)
6
Operating Instructions
VRC1069
(Simp-chinese)
NSP
7
Warranty Card
ARY7020
8
Polyethylene Bag
Z21-038
9
Remote Control Unit
VXX2576
(CU-DV020)
10
Battery Cover
VNK3703
11
Pad F
VHA1220
12
Pad R
VHA1221
13
Mirror Mat Sheet
Z23-007
14
Packing Case
VHG1762
· PACKING PARTS LIST
Mark No.
Description
Part No.
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
· Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
· The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
· Screws adjacent to mark on the product are used for disassembly.
8
7
6
5
8
10
9
3
14
4
2
1
11
12
13
FRONT


background image
DV-K101
4
1
Bonnet Case S
VXX2581
2
DVD Plate
VAM1080
3
Tray Panel Plate
VNK4273
4
Tray Panel
VNK4158
5
Tray
VNL1731
6
· · · · ·
7
· · · · ·
8
Bridge
VNE2069
9
Clamper Plate
VNE2068
10
Clamper
VNL1738
· EXTERIOR SECTION PARTS LIST
Mark No.
Description
Part No.
11
Tray Stopper Spring
VBH1277
12
Tray Stopper
VNL1739
13
Tray Label
VRW1628
14
Screw
BPZ26P080FZK
15
Screw
IBZ30P080FMC
16
Screw
BCZ40P060FNI
17
Screw
BBZ30P080FMC
Mark No.
Description
Part No.
16
1
14
9
8
10
17
16
15
2
3
4
Refer to "2.3 FRONT PANEL SECTION"
15
5
13
11
12
Refer to
"2.4 BOTTOM VIEW SECTION"
17
2.2 EXTERIOR SECTION


background image
DV-K101
5
2.3 FRONT PANEL SECTION
1
FLKY Assy
VWG1957
NSP
2
PWSB Assy
VWG1962
3
KYLB Assy
VWG1961
4
Front Panel
VNK4255
5
FL Lens
VNK4272
6
Name Plate
VAM1067
7
LED Lens
PNW2019
8
Main Key
VNK4269
9
11 Key
VNK4271
10
MICB Assy
VWV1629
· FRONT PANEL SECTION PARTS LIST
Mark No.
Description
Part No.
11
FL Filter
VEC1643
12
Illumination Lens
VNK4264
13
Illumination Filter
VEC1983
14
Illumination Holder
VNK4265
15
Flexible Cable (14P)
VDA1646
(FLKY CN101 ­ DVDM CN105)
16
Screw
BBZ30P080FMC
17
· · · · ·
18
Volume Knob
VNK4279
19
3 Key
VNK4270
20
Light Key
VNK4261
21
Earth Plate
VBK1075
22
Power Button
VNK4059
23
Lens Holder
VNK4266
Mark No.
Description
Part No.
6
4
7
23
19(1/2)
8
15
3
1
16
10
14
11
13
12
5
16
2
16
9
18
20
16
22
21
19(2/2)