background image
ORDER NO.
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880
PIONEER ELECTRONIC CORPORATION 1998
ARP3003
CANAL PLUS TUNER
TS3
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 3
3. SCHEMATIC DIAGRAM ....................................... 6
4. PCB CONNECTION DIAGRAM .......................... 32
5. PCB PARTS LIST ............................................... 40
6. ADJUSTMENT .................................................... 43
CONTENTS
7. GENERAL INFORMATION ................................ 44
7.1 IC ................................................................. 44
7.2 DIAGNOSIS ................................................. 61
7.2.1 TEST SOFTWARE ............................... 61
7.2.2 SELF-DIAGNOSIS MODE ................... 64
7.2.3 TROUBLESHOOTING ......................... 74
7.3 BLOCK DIAGRAM ........................................ 84
8. PANEL FACILITIES AND SPECIFICATIONS .... 85
O ­ SZS SEP. 1998 Printed in Japan
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type
Power Requirement
Model
Remarks
TS3
NYXK
AC230V


background image
TS3
2
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & safety code section 25249.6--Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse)
and/or
(slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide)
et/ou
(fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident
from visual
inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
!
on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or
additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test


background image
TS3
3
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
1
AIR CAP BAG
BHG1048
2
AC POWER CORD (2m: Black) BDG1035
3
OPERATING INSTRUCTIONS
BRC1003
(French)
4
CE DECLARATION CARD
BRM1011
5
POLYETHYLENE BAG
Z21-038
6
REMOTE CONTROL UNIT
BXD1010
7
MODEM CABLE (10m: White) BDH1014
Mark
No. Description
Part No.
PACKING SECTION PARTS LIST
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to
mark on product are used for disassembly.
NOTES:
14
12
10
3
15
4
11
1
2
7
9
6
8
5
8
SCART CABLE (1m: Black)
BDH1009
NSP
9
BATTERY (R03,AAA)
PEM1004
10
SHEET
AHG1153
11
SIDE PAD L
BHA1127
12
SIDE PAD R
BHA1128
14
PACKING CASE
BHD1369
NSP
15
CATALOGUE BAG
BHG1047
Mark
No. Description
Part No.


background image
TS3
4
2.2 EXTERIOR SECTION
13
3
22
22
22
22
15
16
19
26
8
10
7
25
24
4
2
18
22
11
5
1


background image
TS3
5
1
FRONT PANEL ASSY
BMB1071
2
MAIN ASSY
BWE1049
3
FUSE(FU9000 : 2A/250V )
REK1101
4
CARD ASSY
BWZ1847
5
20P FFC (J1)
BDD1020
NSP
6
NAME LABEL(PAP)
BAL1321
7
12P FFC (J3)
BDD1022
8
CHASSIS
BNA1143
9
REAR PANEL
BNC1124
10
SERIAL NO. LABEL(PAP)
BAX1145
11
FRONT ASSY
BWZ1846
12
· · · · · ·
13
POWER ASSY
BWZ1845
14
BONNET CASE
BNE1080
15
PCB SUPPORT
AEC1215
16
PCB HOLDER
AEC1534
17
BARRIER
BEC1173
18
JOINT
BMR1133
NSP
19
MODEM LABEL(PAP)
BAX1211
20
HEXAGON HEADED SCREW BBA1059
21
WASHER FACED NUT
BBN1005
22
SCREW
BBZ30P080FZK
23
SCREW
BPZ40P080FZK
24
SCREW
ABA1027
25
REGULATOR BRACKET
KNG5008
26
PLASTIC BASE
BMA1001
Mark
No. Description
Part No.
EXTERIOR PARTS LIST
9
6
14
23
22
22
17
22
22
22
22
22
20
21