background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
c
Type
Model
Power Requirement
Remarks
CMX-5000
CU-V160
KUC
AC120V
TL
AC110-240V
WY
AC220-240V
CMX-5000
RRV2260
1. SAFETY INFORMATION ....................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................. 4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ... 12
4. PCB CONNECTION DIAGRAM ........................... 45
5. PCB PARTS LIST ................................................ 59
6. ADJUSTMENT ..................................................... 64
CONTENTS
7. GENERAL INFORMATION ................................ 66
7.1 DIAGNOSIS .................................................. 66
7.1.1 TEST MODE ......................................... 66
7.1.2 POWER ON SEQUENCE .................... 71
7.1.3 DISASSEMBLY .................................... 72
7.2 PARTS .......................................................... 75
7.2.1 IC .......................................................... 75
7.2.2 DISPLAY ............................................... 78
8. PANEL FACILITIES AND SPECIFICATIONS .... 80
T ­ IZK FEB. 2000 Printed in Japan
CU-V160
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
COMPACT DISC PLAYER
REMOTE CONTROLLER
A·B AUDIO-OUT SELECT
POWER
MONITOR
MIN
MAX
PHONES
A·B
A·B/
AUTO MIX
PLAYER SELECT
EJECT
DISC
A PLAYER
'
0
EJECT
DISC
B PLAYER
CMX-5000
DJ TWIN CD PLAYER
0
AB
TRACK
LOOP
TEMPO
BPM
17
6
5
4
3
2
13
12
11
10
9
17 18 19 20
16
15
14
8
REMAIN
MS
F
16
10
6
A.CUE
RELOOP
CUE
REV
FWD
SEARCH
PLAY/PAUSE
EJECT
TRACK SEARCH
LOOP
OUT EXIT
OUT ADJUST
OUT ADJUST
RELOOP
TIME MODE
TEMPO
MT
MASTER
TEMPO
0
±6/±10/±16
AUTO CUE
IN/REALTIME CUE
6
0
CUE
REV
FWD
SEARCH
PLAY/PAUSE
EJECT
TRACK SEARCH
LOOP
OUT EXIT
RELOOP
TIME MODE
TEMPO
MT
MASTER
TEMPO
0
±6/±10/±16
AUTO CUE
IN/REALTIME CUE
6
0
AUTO MIX PLAY
BPM SYNC
SHORTTIME
AB
TRACK
DISC
PROGRAM
PLAY MODE SELECT
CLEAR
PLAYER SELECT
BPM/TRACK
PUSH ENTER
BPM/TRACK
SHORTTIME CHANGE
MIXTIME
INSTANT
CHANGE
MIX MODE SELECT
BPM
NEXT
MIN MAX
TRACK
LOOP
TEMPO
BPM
17
6
5
4
3
2
13
12
11
10
9
17 18 19 20
16
15
14
8
REMAIN
MS
F
16
10
6
A.CUE
RELOOP
CMX-5000
CU-V160


background image
2
CMX-5000, CU-V160
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause
cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 ­ Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are identified
by marking with a
on the schematics and on the parts list
in this Service Manual.
The use of a substitute replacement component which does
not have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in
this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
PIONEER.
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
such as Simpson Model 229-2 or equivalent between the
earth ground and all exposed metal parts of the appliance
(input/output terminals, screwheads, metal overlays, control
shaft, etc.). Plug the AC line cord of the appliance directly
into a 120V AC 60Hz outlet and turn the AC power switch
on. Any current measured must not exceed 0.5mA.
(FOR USA MODEL ONLY)
Leakage
current
tester
Reading should
not be above
0.5mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test


background image
3
CMX-5000, CU-V160
(Printed on the Rear Panel)
WY type
TL type
Additional Laser Caution
1. Laser Interlock Mechanism
The position of the switch (S1) for detecting loading
completion is detected by the system microprocessor, and
the design prevents laser diode oscillation when the switch
is not in LPS1 terminal side (when the mechanism is not
clamped and LPS1 signal is high level.) Thus, the interlock
will no longer function if the switch is deliberately set to LPS1
terminal side. ( if LPS1 signal is low level ).
In the test mode
the interlock mechanism will not function.
Laser diode oscillation will continue, if pin 2 of AN8847SB
(IC201) on the CDPB Assy is connected to GND, or pin 19
of IC201 (LDON) is connected to low level (ON), or else the
terminals of Q201 are shorted to each other (fault condition).
2. When the cover is opened, close viewing of the objective
lens with the naked eye will cause exposure to a Class 1
laser beam.
: Refer to page 69.
IMPORTANT
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1.
SERVICING OPERATION OF THE APPARATUS
SHOULD BE DONE BY A SPECIALLY
INSTRUCTED PERSON.
LASER DIODE CHARACTERISTICS
MAXIMUM OUTPUT POWER: 5 mW
WAVELENGTH: 780 ­ 785 nm
LABEL CHECK (for WY and TL types)


background image
4
CMX-5000, CU-V160
2.1 PACKING
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
· Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
· The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
· Screws adjacent to mark on the product are used for disassembly.
1
9
2
3
21
8
4
5
20
7
19
16
17
11
22
(TL Type Only)
12
15
13
10 (KUC Type Only)
6


background image
5
CMX-5000, CU-V160
(1) PACKING PARTS LIST
Mark No.
Description
Part No.
1
Pad A
DHA1448
2
Pad B
DHA1449
3
Pad C
DHA1450
4
Pad D
DHA1451
5
Pad E
DHA1474
6
Packing Case
See Contrast table (2)
NSP
7
Caution SG
DRM1199
8
Sheet
RHX1006
9
Mirror Mat Sheet
Z23-026
(550
× 550 × 0.5)
NSP
10
Limited Warranty
See Contrast table (2)
11
Specialized Connection Cable
DDE1115
for The Remote Controller
12
Forced Ejection Pin
DEX1013
13
Operating Instructions
See Contrast table (2)
14
· · · · ·
15
Caution Tag AP
DRW1897
16
Control Cord
PDE1247
17
Audio Cable (L=1.5m)
VDE1033
18
· · · · ·
19
Polyethylene Bag
Z21-038
(0.03
× 230 × 340)
NSP
20
Silica Gel
AEN7001
NSP
21
Polyethylene Bag
AHG7047
22
Adaptor for 8cm discs
See Contrast table (2)
(2) CONTRAST TABLE
CMX-5000/KUC, TL and WY are constructed the same except for the following :
Mark No.
Symbol and Description
Part No.
Remarks
KUC Type
TL Type
WY Type
NSP
6
10
13
13
13
22
Packing Case
Limited Warranty
Operating Instructions (English)
Operating Instructions (English/Spanish/Chinese)
Operating Instructions
(English/French/German/Italian/Dutch/Spanish)
Adaptor for 8cm discs
DHG1961
ARY7043
DRB1254
Not used
Not used
Not used
DHG1960
Not used
Not used
DRB1256
Not used
DEX1012
DHG1953
Not used
Not used
Not used
DRB1255
Not used