background image
Installation
Note:
· Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
· Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
· Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
to the vehicle.
· Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
· Install the antenna on as flat a place as possible.
· Do not paint the antenna, as this may affect its per-
formance.
· Do not remove the rubber sheet from the antenna
bracket.
· Do not place things such as magnetic cards close
to the antenna because its magnet is strong.
· The antenna may be less sensitive when it is snow-
ing.
· When installing the antenna with the antenna
bracket, be careful to tighten the screws firmly.
After installing, recheck every once in a while that
all screws are tight.
· When installing the antenna with magnet, be care-
ful not to scratch the vehicle body.
· When you use the antenna installed with magnet,
detach the antenna and put it inside the vehicle
every time before entering a car wash system. If it
is left on the outside it may be knocked off and
scratch the vehicle body.
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1760, Long Beach, California 90801, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: (905) 479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
San Lorenzo 1009 3er. Piso Desp. 302
Col. Del Valle Mexico, D.F. C.P. 03100
TEL: 5-688-52-90
Published by Pioneer Corporation.
Copyright © 2001 by Pioneer Corporation.
All rights reserved.
Publication de Pioneer Corporation.
Copyright © 2001 Pioneer Corporation.
Tous droits de reproduction et de traduction
réservés.
Printed in Japan
<CZR3081-A> UC
<KYMFX/01G00000>
XM ANTENNA
Owner's Manual
AN-90XM


background image
Installation
Installing the Antenna Unit
Installation using the magnet of antenna (Fig. 1)
Fig. 1
Installation using the antenna bracket
1. Install the antenna bracket. (Fig. 2)
Fig. 2
Antenna bracket
Screw (A)
Hexagonal wrench
Trunk hood
2. Mount the antenna unit. (Fig. 3)
Fig. 3
Route the antenna cable (Fig. 4)
Fig. 4
Note:
· Secure the antenna cable with the supplied clamper where required.
Clamper
Waterproof pad
Trunk hood
Hexagonal wrench
Screw (B)
Antenna bracket
Loosen so that rain water
cannot enter.


background image
Connecting the Units
Note:
· Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
· Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
Connection Diagram
Fig. 5
XM satellite digital tuner
(e.g. GEX-P900XM)
(sold separately)
Antenna Input
This Product
Green (Terrestrial)
Yellow (Satellite)
5m


background image
Specifications
Power source (Provided by the satellite line)
.............................. 4.7 V DC (3.6 ­ 5.5 V allowable)
Max. current consumption ........................................ 0.1 A
Type ................................................................ Active type
Dimensions
Base .......................... 79 (W)
× 102 (H) × 93 (D) mm
[3-1/8 (W)
× 4 (H) × 3-5/8 (D) in]
Cord ...................................................................... 5 m
Weight ........................................................ 0.3 kg (0.7 lbs)
Note:
· Specifications and the design are subject to possi-
ble modification without notice due to improve-
ments.