DLV-100
SERVICE MANUAL
Digital Light Processing Projector
MODEL
DLV-100
100 - 120 / 200 - 240 V AC, 50 / 60 Hz
UUD
Ref. No. 3701
Nov, 2001
ME
NU
EN
TE
R
CA
NC
EL
SE
LE
CT
AUTO
AD
JUST
PC
CARD
AC
CESS
STA
TUS
POWER
ON
/
STAND
BY
SOUR
CE
INPUT
SAFETY-RELATED COMPONENT
WARNING!!
COMPONENTS IDENTIFIED BY MARK
ON THE
SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE THESE COMPONENTS WITH ONKYO
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN
IN THIS MANUAL.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
1.
Application
This specification sheet applies for DLV-100.
Model
DLV-100
NEC Model code 01152009
2. General
2. General
2. General
2. General
2.1 Operation temperature range
+5 ~ +35 degree C (Humidity 20-80%RH, not in the dewfall.)
2.2 Storage temperature range
-10 ~ +50 degree C
2.3 Power source
100 ~ 120 VAC / 200 ~ 240 VAC +/-10%, 50 / 60 Hz
2.4 Input Current
2.2/1.1A (MAX.)
2.5 Inspection condition
Inspection shall be done by AC120V / 60 Hz unless no rule is specified.
As for the projection condition, the screen is perpendicularly installed to the set and the
projection screen is in WIDE condition of 60 inches. When test, inspector shall be 2 +/- 0.3 m
away from the screen.
Fig. 1 Condition
3. Main parts specifications
3. Main parts specifications
3. Main parts specifications
3. Main parts specifications
3.1 DMD panel
Single Chip Digital Micromirror Device(DMD)
1024
x 768 pixels
3.2 Lens
Manual zoom and focus
F-no.=2.61~2.84, f=28.35~34.02mm
3.3 Lamp
135W DC Lamp
Average lifetime 1,000H
The definition of average lifetime is the time that light becomes half with the continuous
lighting-up.
(Notes)
The lamp bulb can be ruptured, while using a projector.
When the lamp bulb is ruptured, there is a small crack and pieces of glass, which may be
scattered in the lamp case.
2 0.3 m
Screen
Inspector
DLV-100
4. Electric specifications
4. Electric specifications
4. Electric specifications
4. Electric specifications
4.1 Input signal band width
RGB
80MHz
Video
6.5MHz
4.2 Graduation
256 grade full color (16,777,216 color)
4.3 Display resolution
NTSC/PAL/YCbCr
550TV lines
SECAM
300TV lines
RGB
1024dots(H) 768dots(V)
4.4 Input terminal
RGB
1 input: Mini D-SUB 15pin
YCbCr:shares with the RGB terminal
VIDEO
1 input: RCA
S-VIDEO
1 input: DIN 4pin
Audio
1 input: Stereo mini jack
PC Control
1 input: DIN 8pin
USB
1 input: Type A
PC Card
1 input: CompactFlash
4.5 PC Card Viewer
This Viewer can display the JPEG/BMP image which is preserved in CompactFlash (CF).
CF correspond to SanDisk CF 128Mbytes media.
4.6 Y/C Separation
NTSC/PAL
4.7 Input signal (RGB)
Horizontal Freq.
15 ~ 100KHz(RGB: 24KHz or over)
Vertical freq.
50 ~ 120Hz
Pixel clock freq.
Less than 100MHz
Capable resolution
UXGA 1600dot(H) 1200dot(V) Max.
Sync system
Separate Sync/Composite Sync/Sync on G
4.8 Input signal level
RGBHV Input
R,G,B
0.7Vp-p / 75ohm positive
Y
1.0Vp-p / 75ohm positive
Cb,Cr(Pb,Pr)
0.7Vp-p / 75ohm
H/V Sync
4.0Vp-p / TTL posi./nega
Composite Sync 4.0Vp-p / TTL posi./nega
Sync on G
0.3Vp-p / 75 ohm negative
VIDEO
1.0Vp-p / 75 ohm
S-VIDEO
Y:
1.0Vp-p / 75 ohm
C:
0.283Vp-p / 75 ohm
AUDIO
0.5Vrms / 22 K ohm
4.9 Audio output
1W monaural Speaker
DLV-100
4.10 On Screen Display
1. Pull down menu
Basic/Custom menu <> Advanced menu
2. Multilingual menu
English / French /German / Italian / Japanese / Spanish / Swedish
4.11 Remote
Palm type remote unit
4.12 Input current
2.2A 100 ~ 120VAC/1.1A 200 ~ 240VAC
4.13 Plug & Play data
Tab.1 EDID data
0000111122223333444455556666777788889999A
A
A
AB
B
B
BC
C
C
CD
D
D
DE
E
E
EF
F
F
F
00
00
00
00
00
FF
FF
FF
FF
FF
FF
00
38
A3
D3
00
01
00
00
00
10
10
10
10
27
0B
01
02
0E
00
00
78
0A
34
70
95
59
4F
88
26
20
20
20
20
15
4A
53
FF
FF
80
31
59
45
59
61
59
71
59
81
4F
30
30
30
30
81
99
A9
4F
01
01
EA
24
00
60
41
00
28
30
30
60
40
40
40
40
13
00
00
00
00
00
00
1E
F9
15
20
F8
30
58
1F
20
50
50
50
50
20
40
13
00
00
00
00
00
00
1E
00
00
00
FD
00
32
60
60
60
60
78
0F
64
0A
00
0A
20
20
20
20
20
20
00
00
00
FC
70
70
70
70
00
4F
4E
4B
59
4F
20
44
4C
56
31
30
30
0A
00
E2
4.14 Safety test
(1)Dielectric strength test
By the test vessel, under the condition of main power supply ON,
Apply AC voltage of 1500V(+50/-0) ,at 50Hz or 60Hz for 1.5~2 second between power supply
circuit part(AC) and exposure metal part.
No insulation destruction, catching fire, and so on is allowed.
(2) Insulation resistance test
Measure insulation resistance between power supply circuit part(AC) and exposure metal
part (FG) under the condition of main power ON(Stand By mode) by using 500V insulate
ohmmeter.
Insulation resistance shall be more than 50M ohm.
(3)Leakage electric current test
Measure leakage electric current by the leakage ammeter under the condition of main power
supply ON (Standby condition). The measurement impedance should be measured by
the build in resistor of 1.5K , with the bypass capacitor of 0.15 F.
The leakage electric current should be less than 2mA each.
4.15 Signal table
Refer to Tab.2.
DLV-100
5. Optical specifications
5. Optical specifications
5. Optical specifications
5. Optical specifications
5.1 Brightness
Normal
: 630 ANSI lumens minimum
High Brightness : 750 ANSI lumens minimum
It contains 5 % of measurement tolerance.
5.2 Contrast ratio
700 : 1 typical
It contains 20 % of measurement tolerance.
5.3 Relative illumination
More than 70%
On the screen which is shown in figure 2, apply following formula with condition of
Aj as the illumination of point j.
Relative illumination = ( A1 + A3 + A7 + A9 ) / ( 4 x A5 ) x 100 [%]
Fig.2 The measurement point
5.4 Chromaticity
x=0.234 0.344(0.289 +/- 0.055)
y=0.269 0.379(0.324 +/- 0.055)
5.5 Throwing angle
14.3 degree(+/- 5%)
5.6 Projection size
Min.
30 inch / 1.16 m (wide)
Max. 200 inch / 9.67 m (tele)
(For the details, refers to Tab.3.)
5.7 Geometry distortion
Less than 1.11%
5.8 Pixel defects and blemishes
1. No adjacent dark pixels.
2. No bright pixels.
3. No unstable pixels.
4.
5 dark pixels.
5.
7 blemishes
6. No dark blemishes.(Using the blue 180 screen)
7. No bright blemishes.(Using the gray 35 screen)
Note) Blue 180 screen
All areas of the screen are colored a Microsoft paintbrush blue 180(green and red set at 0).
Note) Gray 35 screen
All areas of the screen are colored a Microsoft paintbrush gray 35(green, red, and blue set
at 91).
5.9 Stray light
In all the black signals , a thing with no stray light in the inside of the display area.
DLV-100