GB
F
D
E
I
S
NAD
510
· OWNER'S MANUAL
· MANUEL D'INSTALLATION
· BEDIENUNGSANLEITUNG
· MANUAL DEL USUARIO
· MANUALE DELLE ISTRUZIONI
· BRUKSANVISNINGARNA
REAR PANEL CONNECTIONS (Figure 1.)
WARNING:TO PREVENT FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE
CAUTION: TO PREVENT ELECTRIC SHOCK DO
NOT USE THIS POLARISED PLUG WITH AN
EXTENSION CORD RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: POUR PREVENIR LES CHOCS ELEC-
TRIQUES NE PAS UTILISER CETTE FICHE
POLARISEE AVEC UN PROLONGATEUR, UNE
PRISE DE COURANT OU UNE AUTRE SORTIE DE
COURANT, SAUF SI LES LAMES PEUVENT ETRE
INSEREES A FOND SANS EN LAISSER AUCUNE
PARTIE A DECOUVERT.
The lightning flash with arrowhead, within an equilateral tri-
angle is intended to alert the user of the presence of unin-
sulated "dangerous voltage" within the product's enclo-
sure; that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intend-
ed to alert the user of the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance
Note to CATV system installer: This reminder is provided
to call the CATV installer's attention to Article 820-40 of the
NEC , which provides guidelines for proper grounding and,
in particular, specifies that the cable should be connected
to the grounding system of the building, as close to the
point of cable entry as practical.
NAD
2
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERPLAITE
KLASS 1 LASERAPPARAT
WARNING! INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT! UNSICHTBARE LASERSTRAHLEN TRITT AUS, WENN DECKEL GEÖFFNET
UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST. NICHT DEM STRAHL
AUSSETZEN.
ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE
ER UDE AF FUNKTION.UNDGÅ UDSÆTTELSE FOR STRÅLUNG.
ADVARSEL - USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS
BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR
ÄR URKOPPLADE. STRÅLEN ÄR FARLIG.
VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTÖNNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
ATTENTION:
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SEVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
AFIN DEVITER UN CHOC
ELECTRIQUE, ET LES
CONSEQUENCES GRAVES
QUI POURRAIENT EN
RESULTER, TENTEZ PAS
D'OUVRIR L'APPAREIL ET
DE TOUCHER AUX
COMPOSANTS INTERNES
SANS LA PRESENCE D'UNE
SERVICE PERSONNEL.
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE RADIO INTERFERENCE
REGULATIONS OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
LE PRESENT APPAREIL NUMVERIQUE N'EMET PAS DE
BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES
APPLICABLES AUX APPAREILS NUMERIQUES DE LA CLASSE
B PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE
RADIO ELECTRIQUE EDICTE PAR LE MINISTERE DES
COMMUNICATIONS DU CANADA.
NAD
3
FRONT PANEL CONTROLS (Figure 2.)
DISPLAY (Figure 3.)
QUICK START
1. Use the phono-to-phono lead to connect the
NAD 510's left & right outputs to the CD Input of your
amplifier or receiver.
2. Plug in the AC power cord.
3. Press the POWER button to turn the NAD 510
on.
4. Press OPEN to open the CD drawer and place
the CD in the tray, label side up.
5. Press PLAY to close CD tray and start playing
from the first track.
6. Press PAUSE to stop the CD playing but keep-
ing the current position on the CD. To resume playing
the CD press PLAY.
7. Press Skip
or
to go to other tracks on
the CD.
8. Press Stop to stop the CD playing and return to
the start of the CD.
NOTES ON INSTALLATION.
Your NAD 510 should be placed on a firm, level
surface. Avoid placing the unit in direct sunlight, near
sources of heat and damp or in poorly ventilated posi-
tions.
The CD player comes with phono leads for connec-
tion to your amplifier or receiver. Switch the unit off
before making any connections. Ensure that leads
and connectors are not damaged in any way and all
connectors are firmly pushed home.
If the unit is not going to be used for some time,
disconnect the plug from the AC socket. Should water
get into your NAD 510, shut off the power to the unit
and remove the plug from the AC socket. Have the
unit inspected by a qualified service technician before
attempting to use it again.
Do not remove the cover, there are no user-ser-
viceable parts inside.
Use a dry soft cloth to clean the unit and the CD
Tray. If necessary, lightly dampened the cloth with
soapy water. Do not use solutions containing benzol
or other volatile agents.
As with most digital circuits, the processor inside
your CD player may radiate a small amount of electri-
cal `noise' which could interfere with reception of very
weak radio or TV signals. If this occurs, move the CD
player away from the other devices or switch it off
when viewing or listening to broadcasts.
WARNING TO UK USERS. If this appartus is not
fitted with a UK three-pin plug, do not attempt to
insert the attached plug into a UK mains socket.
Instead, cut the plug from the mains lead and attach
a fused UK three-pin plug using the following safety
advice on wiring.
IMPORTANT. The wires in this mains lead are
coloured BLUE and BROWN;
BLUE: NEUTRAL
BROWN: LIVE
The colours of these mains lead wires may not cor-
respond with the coloured markings identifying the
terminals in your plug. In this case the BROWN wire
must be connected to the terminal which is marked
L(ive) or coloured RED. The BLUE wire must be con-
nected to the terminal marked N(eutral) or coloured
BLACK. No connection should be made to the termi-
nal marked E or coloured green or green and yellow
REAR PANEL CONNECTIONS
1. LINE OUTPUT
The 510's analogue audio output. Using the sup-
plied twin phono-to-phono leads, connect to the left
(white) and right (red) outputs of the NAD 510 to the
`CD' input or other line-level input such as `Aux In' of
your amplifier or receiver. Do not connect this cable
to the amplifier's PHONO input jacks.
2. AC LINE CORD.
Connect this power cord to an AC mains wall outlet
Plug the AC power cord into a live AC wall socket
or to an AC convenience outlet at the rear of your
amplifier.
FRONT PANEL CONTROLS
1. POWER ON/OFF.
POWER switches the player on or off. Pressing the
power switch turns the CD player on, indicated by the
Display Panel becoming active. Pressing the POWER
button again will switch the player off.
When switched Off, no power is supplied to the
NAD 510's electronics.
CAUTION: Disconnect your NAD 510 from the AC
outlet when it is not being used for long periods of
time.
2. CD TRAY
CDs should be placed in the CD Tray, label side
up. The CD Tray has two recesses to securely hold
either 5" or 3" CDs. 5" CDs sit in the larger recess
and 3" CD singles in the smaller central recess.
Use only Audio CDs in your NAD 510. Do not use
CD-V, CD-ROM CD-i or Photo-CD discs in this play-
er, it will not be able to decode and play them.
CAUTION: Do not put anything except a compact
disc into the tray. Foreign objects can damage the
mechanism.
3. OPEN
The OPEN button controls the CD Tray. Press
OPEN to open the Tray. The Display Panel will show
the word `OPEN'.
Press OPEN again to close the tray. The NAD 510
will then close the tray completely. Do not use physi-
cal force to close the tray as this can damage the
drawer mechanism. Always use the OPEN button to
open or close the disc drawer.
With a CD loaded and the tray closed, the CD
Player will scan the disc and Display Panel will show
NAD
4
GB
NAD 510 COMPACT DISC PLAYER
the number of tracks and the total playing time of the
disc. If the CD Tray is empty, then the Display Panel
will display the words `no disc'.
Pressing OPEN when a CD is playing will stop the
playback and open the CD Tray.
Caution: The NAD 510 is not designed for use with
`damping discs' placed on the CD, or two CDs
stacked together in the CD Tray.
Do not close the CD Tray by hand with the power
off. This may result in damage to the mechanism.
4. PLAY
Press PLAY to start playing the CD from the start of
the track shown in the Display Panel. Pressing PLAY
with the CD Tray open and a CD loaded, will close
the CD Tray and start playing the CD from Track 1.
Pressing Play again when the CD is already play-
ing, will re-start playback from the beginning of the
current track.
When the 510 is in Play mode, the Play mode indi-
cator
will be shown in the Display Panel. This will
also show the current track number and position in
the track in minutes and seconds.
5. PAUSE
Pressing PAUSE stops CD playback, without loos-
ing the current position on the CD. Press PLAY to
continue playback from that position on the CD.
Pressing PAUSE twice will cue up the beginning of
the current track, whilst keeping the NAD 510 in
Pause mode. Press PLAY to start playing the CD.
Both SCAN and SKIP can be used in the Pause
mode to select other tracks, or another position on
the current track before returning to play the CD.
When the 510 is in Pause mode, the Play mode
indicator
will flash and the Display Panel will show
the current track number and position in the track in
minutes and seconds.
6. STOP.
The STOP button stops disc playing, cancels any
Repeat mode, and returns the 510 to the start of the
disk. In Stop mode, the Display Panel will show the
total number of tracks and the total playing time of the
disc.
7. TIME
The TIME button switches the Time Display
through three different modes, showing either:
The time played of the current track, in minutes and
seconds.
The playing time remaining for the current track, in
minutes and seconds.
The total time played so far on the disc, in minutes
and seconds.
The total playing time remaining on the CD, in min-
utes and seconds.
The 510 will normally display the current track num-
ber and position in the track in minutes, and seconds
(the default display). Pressing the TIME button will
cycle through the alternative display options and back
to the default display.
8. DISPLAY PANEL
The Display Panel shows information about the
NAD 510's operating modes and information about
the CD currently loaded.
OPEN. The CD Tray is open
no disc. There is no disc in the CD Tray
The unit is in Play mode
[Flashing] The unit is in Pause mode
RANDOM PLAY. The unit is in Random Play Mode
REPEAT. The unit is in Track Repeat mode
REPEAT. [Flashing] The unit is in Disc Repeat
Mode
TRACK NUMBER. Displays the current track num-
ber being played or the track number that will be
played when PLAY is pressed. When the disc is first
loaded, Track Number shows the total number of
tracks available on the disc.
TIME. Is used in conjunction with the TIME button.
Normally in Play mode the Time Display shows the
time played so far on the current track. The TIME but-
ton can switch this to display playing time remaining
on the current track, time played so far on the disc, or
playing time remaining on the disc current track. (See
TIME Button)
TRACK LISTING. Displays a list of tracks available
on the disc. As each track is played its number is
blanked out on the Track Listing, giving a simple indi-
cation of how much of the disc has been played and
how much remains. The display shows up to 20 num-
bered tracks. For CDs with more than 20 tracks, the
20+ indicator illuminates until all the tracks have been
played.
The track Listing display does not operate in
Random mode.
ERROR The Error indicator is displayed when an
`illegal' button sequence is used, such as pressing
any of the controls apart from OPEN/CLOSE when
there is no disc in the CD Tray.
Other common `illegal' button sequences that will
produce the Error display are pressing PAUSE,
TIME or SCAN when the NAD 510 is in Stop mode.
Press STOP to clear the Error message.
9. RANDOM
Pressing RANDOM will play all the tracks on the
CD in a random order. Press RANDOM either from
Stop or Play modes and the 510 will play the tracks
on the CD in random order until all the tracks have
been played.
Press RANDOM button again to cancel Random
play and return the 510 to the normal Play mode.
When the 510 is in Random mode `RANDOM
PLAY' will be shown in the Display Panel.
10. REPEAT
The REPEAT Button switches the NAD 510
between Track Repeat and Disc Repeat modes.
Pressing REPEAT once puts the player into Track
Repeat mode. This will continuously repeat the cur-
rent track as shown in the Display Panel. In Track
Repeat mode, `REPEAT' is shown in the Display
Panel.
NAD
5
GB