background image
TK-7108
© 2001-7 PRINTED IN JAPAN
B51-8592-00 (S) 620
VHF FM TRANSCEIVER /
VHF
TK-7108
SERVICE MANUAL /
Panel assy
(A62-0942-03)
Front glass
(B10-2668-03)
Cabinet
(A01-2178-02)
Key top
(K29-9065-01)
GENERAL ................................................................. 2
OPERATING FEATURES ......................................... 5
REALIGNMENT ...................................................... 11
DISASSEMBLY FOR REPAIR ................................ 14
CIRCUIT DESCRIPTION ......................................... 15
SEMICONDUCTOR DATA ..................................... 24
DESCRIPTION OF COMPONENTS ....................... 26
PARTS LIST ............................................................ 29
EXPLODED VIEW ................................................... 37
PACKING ................................................................. 38
CONTENTS
ADJUSTMENT ........................................................ 39
PC BOARD VIEWS
DISPLAY UNIT (X54-3340-20) ........................... 47
TX-RX UNIT (X57-6293-XX) .............................. 49
SCHEMATIC DIAGRAM ......................................... 55
BLOCK DIAGRAM ................................................... 59
LEVEL DIAGRAM .................................................... 61
TERMINAL FUNCTION .......................................... 63
SPECIFICATIONS ................................. BACK COVER
Please use this manual in place of the service manual (preliminary version), B51-8497-00.
We have added the information on the circuit description, specifications, and K2 version specifications to the service
manual (preliminary version), B51-8497-00.


background image
TK-7108
2
2
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade com-
munications equipment. It contains all required service in-
formation for the equipment and is current as of this publica-
tion date. Changes which may occur after publication are
covered by either Service Bulletins or Manual Revisions,
which are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment informa-
tion, the full part identification number should be included.
This applies to all parts : components, kits, and chassis. If
the part number is not known, include the chassis or kit
number of which it is a part and a sufficient description of
the required component for proper identification.
PERSONNEL SAFETY
The following precautions are recommended for person-
nel safety :
·DO NOT transmit if someone is within two feet (0.6
meter) of the antenna.
·DO NOT transmit until all RF connectors are secure and
any open connectors are properly terminated.
· SHUT this equipment when near electrical blasting caps
or while in an explosive atmosphere.
· All equipment should be properly grounded before
power-up for safe operation.
· This equipment should be serviced by only qualified tech-
nicians.
........................................................................... 2
.................................................................... 5
.................................................................. 11
....................................................... 14
.................................................................. 15
.............................................................. 24
.................................................................. 26
..................................................................... 29
............................................................... 37
.......................................................................... 38
.......................................................................... 39
PC
DISPLAY UNIT (X54-3340-20) ............................ 47
TX-RX UNIT (X57-6293-XX) ............................... 49
...................................................................... 55
...................................................................... 59
...................................................................... 61
................................................................... 63
.......................................................................
GENERAL /
·
0.6
·
·
·
·


background image
3
TK-7108
PRE-INSTALLATION CONSIDERNATIONS
1. UNPACKING
Unpack the radio from its shipping container and check
for accessory items. If any item is missing, please contact
KENWOOD immediately.
2. LICENSING REQUIREMENTS
Federal regulations require a station license for each ra-
dio installation (mobile or base) be obtained by the equip-
ment owner. The licensee is responsible for ensuring trans-
mitter power, frequency, and deviation are within the limits
permitted by the station license.
Transmitter adjustments may be performed only by a li-
censed technician holding an FCC first, second or general
class commercial radiotelephone operator's license. There
is no license required to install or operate the radio.
3. PRE-INSTALLATION CHECKOUT
3-1. Introduction
Each radio is adjusted and tested before shipment. How-
ever, it is recommended that receiver and transmitter opera-
tion be checked for proper operation before installation.
3-2. Testing
The radio should be tested complete with all cabling and
accessories as they will be connected in the final installa-
tion. Transmitter frequency, deviation, and power output
should be checked, as should receiver sensitivity, squelch
operation, and audio output. Signalling equipment operation
should be verified.
4. PLANNING THE INSTALLATION
4-1. General
Inspect the vehicle and determine how and where the
radio antenna and accessories will be mounted.
Plan cable runs for protection against pinching or crush-
ing wiring, and radio installation to prevent overheating.
4-2. Antenna
The favored location for an antenna is in the center of a
large, flat conductive area, usually at the roof center. The
trunk lid is preferred, bond the trunk lid and vehicle chassis
using ground straps to ensure the lid is at chassis ground.
4-3. Radio
The universal mount bracket allows the radio to be
mounted in a variety of ways. Be sure the mounting surface
is adequate to support the radio's weight. Allow sufficient
space around the radio for air cooling. Position the radio
close enough to the vehicle operator to permit easy access
to the controls when driving.
4-4. DC Power and wiring
1. This radio may be installed in negative ground electrical
systems only. Reverse polarity will cause the cable fuse
to blow. Check the vehicle ground polarity before installa-
tion to prevent wasted time and effort.
GENERAL /
1.
KENWOOD
2.
FCC
3.
3-1.
3-2.
4.
4-1.
4-2.
4-3.
4-4.
1.


background image
4
TK-7108
GENERAL /
2. Connect the positive power lead directly to the vehicle
battery positive terminal. Connecting the Positive lead to
any other positive voltage source in the vehicle is not rec-
ommended.
3. Connect the ground lead directly to the battery negative
terminal.
4. The cable provided with the radio is sufficient to handle
the maximum radio current demand. If the cable must be
extended, be sure the additional wire is sufficient for the
current to be carried and length of the added lead.
5. INSTALLATION PLANNING ­ CONTROL STATIONS
5-1. Antenna system
Control station. The antenna system selection depends
on many factors and is beyond the scope of this manual.
Your KENWOOD dealer can help you select an antenna sys-
tem that will best serve your particular needs.
5-2. Radio location
Select a convenient location for your control station radio
which is as close as practical to the antenna cable entry
point. Secondly, use your system's power supply (which
supplies the voltage and current required for your system).
Make sure sufficient air can flow around the radio and power
supply to allow adequate cooling.
SERVICE
This radio is designed for easy servicing. Refer to the
schematic diagrams, printed circuit board views, and align-
ment procedures contained in this manual.
speaker jack cap
Power input
connector
Antenna connector
NOTE
If you do not intend to use the 3.5-mm jack for the exter-
nal speaker, fit the supplied speaker-jack cap to stop dust
and sand getting in.
2.
3.
4.
5 -
5-1.
KENWOOD
5-2.
3.5mm


background image
5
TK-7108
1.
1-1.
q
we
t
r
y
u
i
o
q
()
1
w
e
r
PF () ()
t
PF ()
y
1/ 2/ 3/ 4
14
58
u
i
o
PTT
1-3.
·
· /
·
·
·
·
· ()
·
14
1-4.
1-5.
1-2.