background image
LVT0953-002A
[J, C]
Home Cinema DD Speaker System
Système d'enceinte Home cinéma DD
SX-XD33
Consists of SX-XDS33 and SX-XDC33
Se compose de SX-XDS33 et SX-XDC33
INSTRUCTIONS
MANUEL D'INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
English
Fran
ç
ais


background image
­ 1 ­
Contents
Warnings, Cautions and Others .............................................................. 2
Assembly ................................................................................................. 3
Additional information .............................................................................. 6
Specifications .......................................................................................... 7
Contenus
Avertissements, précautions et autres .................................................... 8
Montage .................................................................................................. 9
Informations complémentaires ............................................................... 12
Spécifications ......................................................................................... 13
Français
English
EN_SX-XD33[J/C].p65
03.3.11, 6:59 PM
1


background image
­ 2 ­
English
Checking the supplied Accessories
Check to be sure you have the following supplied accessories.
The number in parenthesis indicates the quantity of the piece
supplied.
· Speaker cords
Approx. 6 m (19.7 feet) (3: for satellite speakers placed in
front position and a center speaker)
Approx. 15 m (49.2 feet) (2: for satellite speakers placed in
rear position)
· Screws
M5 x 12 mm (M5 x 1/2 in.) (4)
M4 x 25 mm (M4 x 1 in.) (12)
· Washers
(4)
If any of the items above are missing, contact your dealer
immediately.
Speaker and Speaker cords--
to improve the sound quality
About DD (Direct Drive) speaker
DD (Direct Drive) technology improves sound localization
and transmits the powerful sounds.
About the OFC cord
The core wires of the supplied speaker cords are made of
OFC (Oxygen Free Copper). This OFC cord enables high
quality sound reproduction.
When connecting the speaker cords
Make sure to match the polarity (
ª and ·); otherwise, the
sound will lose the surround effect.
After connecting, check that the exposed cores are fully
inserted into the terminal.
When using other speaker cords
Observe the following;
· Buy thick speaker cords rather than thin cords, and make
them as short as possible for connection.
· Use speaker cords of the same length for both left and
right speakers.
· Do not use long speaker cords; otherwise, the sound
quality may deteriorate.
Thank you for purchasing a JVC speaker system.
Before you begin using these speakers, please read the
instructions carefully to be sure you get the best possible
performance. If you have any questions, consult your JVC
dealer.
Warnings, Cautions and Others
Precautions for installation
· Do not install the speakers on an uneven surface or in a
place subject to vibration; otherwise, they may fall over,
causing damage or injury.
­ Take the occurrence of earthquakes or other
physical shocks into consideration when
selecting the installation place, and secure
the speakers thoroughly.
· To prevent deformation or discoloration of the
cabinet, do not install the speakers where they
are exposed to direct sunlight or high humidity,
and avoid installation near air conditioning
outlets.
· Speaker vibrations may cause howling. Place
the speakers as far away from the player as
possible.
· The speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, it may
cause color distortions. So, pay attention to the following
when installing the speakers.
­ When placing the speakers near a TV set, turn off the TV's
main power switch or unplug it before installing the
speakers.
Then wait at least 30 minutes before turning on the TV's
main power switch again.
Some TVs may still be affected even though you have
followed the above. If this happens, move the speakers
further away from the TV.
· Tuner reception may become noisy or hissing if a speaker is
installed near the tuner. In this case, leave more distance
between the tuner and the speakers or use an outdoor antenna
for better tuner reception without interference from the speakers.
Precautions for Daily Use
· To maintain the appearance of the speakers
Wipe with a dry, soft cloth if the cabinet or control panel
should become dirty.
If very dirty, apply a small amount of water or neutral detergent
to the cloth and wipe clean, then wipe with a dry cloth.
· To improve the sound field
If the speakers are facing a solid wall or glass
door, etc., it is recommended to furnish the wall
with materials that absorb sounds, for example
by hanging up thick curtains, to prevent
reflections and standing waves.
· To use the speakers without any trouble
­ Do not reproduce sounds at so high a volume that they are
distorted; otherwise, the speakers may be damaged by
internal heat buildup.
­ When moving the speakers, do not pull the speaker cords;
otherwise, the speakers may fall over, causing damage or
injury.
­ When holding a satellite speaker, do not grasp the speaker
(upper) portion, but always grasp the leg (lower) portion of
the satellite speaker.
Satellite speaker
Leg
Speaker
grille
Speaker
cord
EN_SX-XD33[J/C].p65
03.3.11, 6:59 PM
2


background image
­ 3 ­
English
Assembling the satellite speakers
Each speaker (except the center speaker) has been divided into
three parts for shipment. Before using this speaker system,
assemble it first by following the procedure below.
· Prepare a Phillips screw driver.
Before assembling--
· Take care not to drop the stand while assembling;
otherwise, it may cause damage to the floor or injury.
· Ensure enough space for assembly and installation.
· Place a large, thick cloth on the floor where you
assemble the speaker, so you can protect the floor and
the speaker itself.
· Use the speaker only after assembly is fully and correctly
done.
Attaching the leg and the stand
1 Remove the terminal cover from the leg.
First remove the screw on the terminal cover, then detach
the cover by pulling it upward.
· You will need to use the removed screw in step 5 on page
4.
Cushion
2 Join the leg to the stand.
· Rotate either the leg or stand so that the
mark on the
leg and the
mark on the stand are facing the same
direction.
· Make sure to match the screw holes on the leg with those
on the stand so that they are aligned correctly.
3 Fix the leg to the stand with three of the
supplied screws--long: M4 x 25 mm
(M4 x 1 in.).
· Do not tighten each screw completely as you put them in
place.
First put all screws in, then tighten them evenly and firmly.
It is recommended to place a cushion under the leg.
· You can tighten the screws easily by placing the leg
horizontally.
Assembly
mark
mark
Stand
Leg
Leg
Screw
claws
Terminal
cover
grooves
Speaker
section
Leg
Stand
Screw
Stand
Leg
EN_SX-XD33[J/C].p65
03.3.11, 6:59 PM
3


background image
­ 4 ­
English
3) Insert the speaker cord into the speaker terminal
inside the leg.
1 Press and hold the clamp.
2 Insert the exposed core of the speaker cord fully
into the terminal.
· Connect the cord with the black stripe to the
·
terminal.
3 Release your finger.
5 Attach the terminal cover to the leg.
Push cords fully inside the leg. Then fix the terminal cover
using the screw you removed in step 1.
4 Connect the speaker cord to the speaker
terminal of the leg.
· Use the 6-meter (19.7 feet) speaker cords for front speakers
and 15-meter (49.2 feet) speaker cord for rear speakers.
· Each speaker cord has its name tag attached to one end.
Attach the end without the name tag to the speaker
terminal.
1) Insert the speaker cord inside the stand as illustrated
below.
· Pull the speaker cord out of the center of the stand by
about 50 cm (19 11/16 in.).
2) Insert the tips of the speaker cord into the leg and pull
them out as illustrated below.
Tag
To the speaker
terminal of the leg
The cord with the
black stripe is on this
side, facing up.
Stand
To be continued on the next page
Terminal
cover
Screw
claws
grooves
Leg
The cord with
the black stripe.
Leg
12
3
EN_SX-XD33[J/C].p65
03.3.11, 6:59 PM
4