JVC SX-LC33AK - Owner's Manual Immediate Download

LVT1264-001A

[U, UP]

SX-LC33

SPEAKER SYSTEM

INSTRUCTIONS

English

cover_SX-LC33[U_UP]f.p65

04.7.26, 3:50 PM

English

Warnings, Cautions and Others

7 Checking the supplied accessories

· Speaker cord (3m, 1)

· Feet (4)

If any item is missing, contact your dealer immediately.

7 Attaching the feet

Attach the supplied feet on the bottom of the speaker, so that you

can protect the speaker cabinet, decrease the vibration of the

speaker cabinet and prevent the speaker from slipping.

· Turn the speaker upside down and attach the feet as

illustrated.

Place a large, thick cloth under the speaker in order to

protect the floor and the speaker.

7 To remove the speaker grille

To remove the speaker grille, insert your fingers at the bottom

of the speaker grille, then pull upward.

To attach the speaker grille, put the projections of the speaker

into the holes of the speaker grille.

· Do not push the speaker grille strongly.

7 Precautions for installation

· Do not install the speakers on an uneven surface or in a place

subject to vibration; otherwise, they may fall over, causing

damage or injury.

Take the occurrence of earthquakes or other

physical shocks into consideration when

selecting the installation place, and secure the

speakers thoroughly.

· To prevent deformation or discoloration of the

cabinet, do not install the speakers where they are

exposed to direct sunlight or high humidity, and

avoid installation near air conditioning outlets.

· Speaker vibrations may cause howling. Place the

speakers as far away from the player as possible.

· The speakers are magnetically shielded to avoid

color distortions on TVs. However, if not installed

properly, it may cause color distortions. So, pay attention to the

following when installing the speakers.

When placing the speakers near a TV set, turn off the TV's

main power switch or unplug it before installing the

speakers.

Then wait at least 30 minutes before turning on the TV's

main power switch again.

Some TVs may still be affected even though you have followed

the above. If this happens, move the speakers further away

from the TV.

· Tuner reception may become noisy or hissing if a speaker is

installed near the tuner. In this case, leave more distance

between the tuner and the speakers or use an outdoor

antenna for better tuner reception without interference from

the speakers.

7 Precautions for daily use

· To maintain the appearance of the speakers

Wipe with a dry, soft cloth if the cabinet should become dirty.

If very dirty, apply a small amount of water or neutral detergent

to the cloth and wipe clean, then wipe with a dry cloth.

· To improve the sound field

It is recommended to leave a space of more than 50 cm

between the speakers and the wall.

If the speakers are facing a solid wall or glass

door, etc., it is recommended to furnish the wall

with materials that absorb sounds, for example by

hanging up thick curtains, to prevent reflections

and standing waves.

· To use the speakers without any trouble

Do not reproduce sounds at so high a volume that they are

distorted; otherwise, the speakers may be damaged by

internal heat buildup.

When moving the speakers, do not pull the speaker cords;

otherwise, the speakers may fall over, causing damage or

injury.

Bottom of the

speaker

Peel off

Thank you for purchasing a JVC speaker.

Before you begin using it, please read the instructions carefully

to be sure you get the best possible performance. If you have any

questions, consult your JVC dealer.

EN_SX-LC33[U_UP]f.p65

04.7.26, 3:50 PM

English

Connection

Type:

2-way 3-speaker bass-reflex type

Magnetically-shielded type

Speakers

Woofer:

13.5 cm cone x 2

Tweeter:

1.9 cm dome x 1

Power handling capacity: 120 W

Specifications

7 Connecting the speaker cord to the speaker

Connect the speaker cord to the speaker as follows.

1 Twist and remove the insulation at the end of each

speaker cord before connecting.

2 Rotate the speaker terminal knob counterclockwise and

fit the speaker cord into the groove. Then rotate the knob

clockwise to secure the cord.

7 Connecting the speaker system to the amplifier

Before connection--

· Turn off the power to the amplifier before connecting the

speaker system; otherwise, the speakers may be damaged.

· The impedance of the speaker is 6

. Before connecting it to

your amplifier, check the speaker impedance range of your

amplifier. If the impedance of this speaker is out of the speaker

impedance range indicated on the amplifier, you cannot

connect this system to the amplifier.

· The maximum power handling capacity of the SX-LC33 is

120 W. Excessive input will result in abnormal noise and

possible damage.

· Be sure to turn down the volume level to prevent unwanted

noise before performing following operations:

Turning on or off other components,

Operating the amplifier,

Tuning FM stations,

Fast-forwarding a tape,

Continuously reproducing high frequency oscillation or high

pitch electronic sounds.

· When using a microphone, do not aim it at the speakers or

use it near the speakers; otherwise, the howling which occurs

may damage the speakers.

· Before replacing the cartridge, always turn off the power to the

turntable; otherwise, the clicking noise may damage the

speakers.

Impedance:

Crossover frequency:

4 000 Hz

Frequency range:

52 Hz to 80 000 Hz

Sound pressure level:

89 dB/W·m

Dimensions (W x H x D):

150 mm x 415 mm x 292.5 mm

Mass:

8.0 kg

Design and specifications subject to change without notice.

About speaker cords--to improve the sound quality

About the OFC cord

The core wires of the supplied speaker cords are made of OFC (Oxygen Free Copper). This OFC cord enables high quality

sound reproduction.

When connecting the speaker cords

Make sure to match the polarity (

ª and ·); otherwise, the surround effect will become less effective.

After connecting, check that the exposed cores are fully inserted into the terminal.

When using other speaker cords

Observe the following;

· Buy thick speaker cords rather than thin cords, and make them as short as possible for connection.

· Do not use long speaker cords; otherwise, the sound quality may deteriorate.

· Use speaker cords of the same length for both left and right speakers.

· Using a special speaker cord such as a litz wire, a coaxial cable, or a cord which has the specified connecting directionality

may influence the sound quality.

Tighten

Loosen

Silver

ª terminal

(Red)

· terminal

(Black)

Copper

To the speaker

terminal of amplifier

To the speaker

terminal of amplifier

EN_SX-LC33[U_UP]f.p65

04.7.26, 3:50 PM

50 cm

JVC

(3m, 1)

(4)

Ch_SX-LC33[U_UP].p65

7/22/04, 10:41 AM

Page 4

Adobe PageMaker 6.5C/PPC

13.5 cm

x 2

1.9 cm

x 1

120 W

· SX-LC33

120 W

4 000 Hz

52 Hz

80 000 Hz

89 dB/W·m

150 mm x 415 mm x 292.5 mm

8.0 kg

OFC

Ch_SX-LC33[U_UP].p65

7/22/04, 10:41 AM

Page 5

Adobe PageMaker 6.5C/PPC