JVC MC-R434 - Owner's Manual Immediate Download

MC-R434U

LST0172-001A

MC-R434U

DVD-RAM/R

DRIVE

INSTRUCTIONS

Thank you for purchasing the JVC MC-R434U DVD-RAM/R DRIVE.

Before you start operating this unit, please read the instructions

carefully in order to obtain the best possible performance.

For Customer Use:

Enter below the Model No. and Serial

No. which are located at the top of the

unit. Retain this information for future

reference.

Model No. MC-R434U

Serial No.

nted in Japan

T0172-001A

This instruction book is made from 100% recycled paper.

ENGLISH

DEUTSCH

FRANÇAIS

03.11.18, 9:23 AM

INSTALLATION FLOW

Follow the steps below for installation.

PRECAUTIONS BEFORE USE

INSTALLATION

Page 3, 4

Install the MC-R434U in the CD/DVD Library.

Procedure for Opening the Door of the CD/DVD Library

Procedure for Opening the Drive Storage Cover of the

CD/DVD Library

Procedure for Determining the Setup Position for the MC-R434U

Procedure for Installing the MC-R434U in the CD/DVD Library

CONNECTION

Page 4, 5

Connect the MC-R434U to the CD/DVD Library.

Procedure for Connecting the Cables to the Back of the MC-R434U

SETUP

Page 5

Set the SCSI ID of the MC-R434U and close the door of the CD/

DVD Library.

Procedure for Setting the DIP Switch

Procedure for Attaching the Drive Storage Cover of the CD/DVD

Library

Procedure for Closing the CD/DVD Library Door

EXECUTION OF AUTOMATIC

DRIVE DETECTION MODE.

Page 6

Execute the automatic drive detection mode and connect the host

computer.

Procedure for Executing the Automatic Drive Detection Mode of

the CD/DVD Library

Procedure for Connecting the CD/DVD Library to the Host Com-

puter

The ambient temperature around the CD/DVD Library should

be maintain at about 5°C to 30°C when a MC-R434U is con-

nected to multiple units of the MC-8100LU or MC8200LU/

8600LU the CD/DVD Library, as mentioned below.

· MC-8100LU

: 4 units

· MC-8200LU/8600LU : 6 units

1. DANGER: Invisible laser radiation will occur if the unit is

open due to a failed or defective interlocking device.

2. CAUTION: Do not open the top cover. There are no user

serviceable parts inside the unit; leave all servicing to

qualified service personnel.

The MC-R434U is a DVD-RAM/R drive designed for use with

the JVC MC-8100LU/8200LU/8600LU "CD/DVD Library".

When installing this unit in a Library that is being used, please

read the instruction manual carefully.

The MC-R434U cannot be operated on its own.

This unit cannot be used in combination with the following

models.

· CD-ROM Library : MC-1000 series/2000 series

· DVD-RAM Library: MC-7000 series

· CD/DVD Library

: MC-8000 series

For the compatible discs, see the Specifications on page E7.

03.11.17, 5:15 PM

ENGLISH

1. Select the [DOOR OPEN MODE] on the MENU screen of

the CD/DVD Library's LCD.

2. Press and hold the "SELECT" switch for five seconds.

3. Turn off the power of the CD/DVD Library when [THE DOOR

CAN BE OPENED] message is displayed on the LCD.

4. Insert the key in the key cylinder located at the center of

the door to unlock and open the door.

* The illustration shows the CD/DVD Library with the drive storage

cover removed for ease of description.

1. Remove the screws from the drive storage cover of the

CD/DVD Library.

2. Remove the drive storage cover.

1. Install the drives to the drive slots No.1 through No.6 (No. 1

through No. 4 in the case of the MC-8100LU) sequentially.

It makes the work easy if the drives are installed from

the lowest number to the highest.

<MC-8100LU drive storage section> <MC-8200LU drive storage section>

Install the MC-R433U in the CD/DVD Library.

Before starting installation, be sure to turn both the

host computer and peripherals off.

For information related to the CD/DVD Library, refer

to the instruction manual for the CD/DVD Library.

INSTALLATION

Drive locking

screw mounting

hole

Drive storage

section

Drive storage

section

Drive locking

screw mounting

hole

Drive No. 3

Drive No. 4

Drive No. 1

Drive No. 2

Drive No. 6

Drive No. 3

Drive No. 4

Drive No. 5

Drive No. 1

Drive No. 2

Drive storage

cover

Screw

Drive storage

section

Drive storage

section

Screw

Drive storage cover

Procedure for Opening the Door of the

CD/DVD Library

Procedure for Opening the Drive Storage

Cover of the CD/DVD Library

Procedure for Determining the Setup

Position for MC-R434U

03.11.17, 5:15 PM

<MC-R434U connection example>

1. Connect the power supply cable, control cable and SCSI

cable to the connectors at the rear of the MC-R434U.

When using the MC-8100LU, the No. of the cable must

always correspond to the No. of the drive bay to which it

is being connected. If a cable with the wrong number is

connedted, it will lead to the equipment malfunctioning.

When using an MC8200LU/8600LU, connect the con-

trol cables which lead from the side of the drive bay where

the MC-R434 is to be inserted.

Insert all connectors firmly.

SCSI cables are connected as a daisy chain connec-

tion. Each connector should be connected to the drive

positions as illustrated in the diagram.

· The SCSI cable, which is built into the MC-8100LU/

8200LU/8600LU standard models, terminates at the

location where the connection is physically terminated.

<MC-R434U rear panel>

Interior

Drive 4

Drive 3

Drive 2

Drive 1

Library SCSI board

Drive 6

Drive 5

Terminator

Internal SCSI (LVD) cable

68-pin external SCSI connector

To host computer (SE/LVD)

SE-LVD conversion board

Terminator

Internal SCSI (SE) cable

Power cable

Control cable

DIP switch

SCSI cable

14p

Procedure for Connecting the Cables to

the Back of the MC-R434U

1. Insert the MC-R434U from the rear of the CD/DVD Library

Be sure not to damage the sensor slit.

Make sure that the direction of the MC-R434U is correct

when inserting it.

Be sure that the cables connected to the rear of the CD/

DVD Library are not caught or pinched when inserting

the MC-R434U.

2. Insert the MC-R434U slowly until the screw installation hole

located on the side of the MC-R434U and the screw instal-

lation hole located on the drive locking section are aligned.

3. Screw in the provided drive locking screw to the screw in-

stallation hole of the drive locking section.

Tighten the screw firmly.

If the drive locking screw is loose, the drive and/or Li-

brary may be damaged.

Sensor slit

MC-R434U

Drive locking

screw

MC-R434U

<MC-R434U insertion direction>

<MC-R434U locking method>

Procedure for Installing the MC-R434U in

the CD/DVD Library

Connect the MC-R434U to the CD/DVD Library.

Also refer to the instruction manual for the CD/

DVD Library.

CONNECTION

03.11.17, 5:15 PM

ENGLISH

2. Connect the two LVD power cables (6P) to the SE-LVD

conversion board.

Both cables have identical connector types, so that ei-

ther cable can be connected to either connector on the

SE-LVD conversion board.

3. Connect the internal SCSI (SE) cable (50P) to the SE-LVD

conversion board.

The other end of the internal SCSI (SE) cable is con-

nected to the library SCSI board in the library.

4. Connect the internal SCSI (LVD) cable (68P) to the drives.

The other end of the internal SCSI (LVD) cable is con-

nected to the SE-LVD conversion board.

Connecting the cables

Library

<SE-LVD conversion board>

To each drive

Internal SCSI (LVD) cable

LVD

power cable

Internal SCSI (SE) cable

50p

68p

Drive 4

Drive 3

Library SCSI board

Internal SCSI

(SE) cable

To SE-LVD conversion board

Drive 2

Drive 1

Terminator

Internal SCSI cable (approx. 1.0 m)

Terminator

1. Secure the cover with the screws that were removed.

"Procedure for Opening the Drive Storage Cover of

the CD/DVD Library" on page 3.

1. Close the door and lock the key cylinder.

Procedure for Attaching the Drive

Storage Cover of the CD/DVD Library

Procedure for Closing the CD/DVD

Library Door

<MC-R434U DIP switch settings on the rear panel>

Procedure for Setting the DIP Switch

Set the SCSI ID of the MC-R434U and close the door

of the CD/DVD Library.

Always turn the power of the CD/DVD Library off when

the dip switches are moved.

For the details of the default factory settings, please

refer to the section "SCSI ID No. SETTING" of the

instructions from the CD/DVD Library.

SETUP

*:Factory setting.

SCSI ID No.

Switch

ID2

ID1

ID0

OFF

4ON

OFF

5ON

OFF

6ON

OFF

7ON

OFF

(Factory setting)

RSV

1234

1. ID2, ID1, ID0: Setting of the SCSI ID No. of each drive.

When setting the SCSI ID No., use a number that is not

being used by other SCSI devices on the same bus.

The MC-R434 should be used with one of the SCSI ID

No. 0 to 7. It cannot be used with No. 8 to 15.

RSV: Not available

03.11.17, 5:15 PM