ENGLISH
DEUTSCH
FRANÇAIS
MC-D207U
LST0038-001B
INSTRUCTIONS
DVD-ROM DRIVE
For Customer Use:
Enter below the Model No. and Serial
No. which are located at the top of the
unit. Retain this information for future
reference.
Model No. MC-D207U
Serial No.
This instruction manual has been manufactured from 100% recycled paper.
2
Thank you for purchasing the JVC MC-D207U DVD-ROM DRIVE.
Before you start operating this unit, please read the instructions carefully in order to obtain the best possible performance.
1. DANGER: Invisivle laser radiation will occur when the unit
is open with a failed or defeated interlock.
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to quali-
fied service personnel.
3
ENGLISH
ACCESSORIES AND DOCUMENTATION
Accessories
Drive locking screw (M3 with washer) ......................... 2 (including one spare)
Instructions .............................................................. 1
Documentation
Drive locking section
· Figure shows the MC-1200U/E
· Figure shows the MC-2200U
or MC-8200U
· Figure shows the MC-2100U
or MC-8100U
Drive locking screw
mounting hole
Drive locking section
Drive locking section
Drive locking screw
mounting hole
Drive locking screw
mounting hole
This unit is a DVD-ROM drive with a 7x speed capability. It especially designed for the JVC CD-ROM Library or CD/DVD
Library. It is not compatible with the MC-7000 series "DVD-RAM Library".
The MC-D207U cannot be operated separately.
A DVD videodisk playback is not possible with the MC-D207U.
INSTALLATION
1. How to Open the Door of the JVC Library
In order to open the door, please also refer to the section
"HOW TO OPEN THE DOOR DURING OPERATION" in the in-
structions for the JVC CD-ROM or CD/DVD Library.
1. Select the [DOOR OPEN MODE] on the MENU screen of the
LCD display section.
2. Press and hold the "SELECT" switch for five seconds.
3. Turn off the power of the JVC Library when the [YOU MAY OPEN
THE DOOR] or [THE DOOR CAN BE OPENED] message is
displayed on the LCD display section.
4. Insert the key in the key cylinder located at the center of the
door and turn it 90 degrees counterclockwise to unlock and open
the door.
Before you start installing the DVD-ROM Drive, be sure to
turn off the power of the host computer, all peripheral de-
vices and the Library.
Please refer to the instruction manual of your Library for more information about the CD-ROM or CD/DVD Library.
ROM Replacement
When this drive is mounted in the MC-1200U/1600U or MC-2200U/2600U CD-ROM Library, certain serial numbers may
require to replace the ROM.
Read the section "ROM REPLACEMENT IN THE CD-ROM LIBRARY" on page 6 for the first time.
4
INSTALLATION
Sensor slit
·Beware of damage
Drive locking
screw
Drive storage
section
Drive storage
section
Drive storage
cover
Drive storage
cover
Drive storage
section
Drive No.6
Drive No.5
Drive No.4
Drive No.3
Drive No.2
Drive No.1
Drive No.4
Drive No.3
Drive No.2
Drive No.1
Screws
Screws
Screws
Drive storage
section
· Figure shows the MC-2200U
or MC-8200U
Screws
Drive No.6
Drive No.5
Drive No.4
Drive No.3
Drive No.2
Drive No.1
Drive storage cover
· Figure shows the MC-2100U
or MC-8100U
· Figure shows the MC-1200U/E
To be reused when
refitting the cover later.
2. How to Open the Drive Storage Cover
Please also refer to the corresponding sections in the
Library instructions.
1. Remove the screws from the drive section cover,
which is located at the rear of the Library.
2. Remove the drive storage cover.
4. How to Install the DVD-ROM Drive
1. Install drive from the No.1 to No.6 slot in that order without skipping.
Starting installation from the lowest No.1 slot will simplify future installation work.
1. Insert the drive from the rear of the JVC CD-ROM or CD/DVD Library.
Pay attention not to damage the sensor slit.
Always insert the DVD-ROM Drive correctly.
Check that cables connected on the rear of the unit are not caught
or pinched when inserting the DVD-ROM Drive.
2. Insert the DVD-ROM Drive slowly until the screw installation hole
located on the side of the DVD-ROM Drive and the screw installation
hole located on the drive locking section are aligned.
3. Lock the DVD-ROM Drive in place by using the drive locking screw
on the door panel side of the drive.
Tighten the screw firmly.
If the drive locking screw is loose, the drive and/or CD-ROM, CD/
DVD Library could suffer damage.
3. How to Determine the Installation Position of the DVD-ROM Drive
Drive storage section
Drive locking section
5
ENGLISH
INSTALLATION
5. How To Connect Cables To The DVD-ROM Drive
1. Connect the power supply cable, control cable and SCSI cable to the connectors at the rear of the DVD-ROM Drive.
Connect to the drive the power supply cable and control cable which extend from the side of the DVD-ROM drive
installation slot.
With the MC-2100U and the MC-8100U models be sure to connect a control cable with the same component No., as
the drive bay No., otherwise proper operation may not be possible.
Insert all connectors firmly.
6. How To Set The Dip and Slide Switches
Always turn OFF the power of Library when you set the dip switch modes.
1. TERM : This selects the use of the built-in terminator.
To use the built-in drive terminator, set the TERM of the drive to ON and the TERM of other drives to OFF.
When not using the built-in terminator, attach an active SCSI terminator to the OUT side of the SCSI connector.
In this case, set the TERM of all built-in drives to OFF.
Power supply cable
Control cable
SCSI cable
Slide switch
14p
4p
Dip switches
WN
Rear section of the DVD-ROM Drive
SCSI cables should be connected as a daisy chain connection. Each connector may be connected to the drive
positions as illustrated in the diagram.
Terminate the physical end of the SCSI bus. To use the built-in drive terminator, read 6 -1.
It is recommended to use an external terminator to improve the stability of the SCSI bus communications.
Connection example of a SCSI cable
(Factory setting)
ON
OFF
1
TERM
ID
2
ID
1
ID
0
234
WN
DIP switch
Slide switch
DVD-ROM Drive
DVD-ROM Drive
Library SCSI board
SCSI connector
To be connected with host
computer's SCSI host adapter
Connect an active terminator.
OUT 2
IN
2
OUT 1
IN
1
Internal SCSI ribbon cable
· Up to six drives can be connected normally.
(But only four drives in the case of the MC-2100U
and the MC-8100U)
DVD-ROM Drive
(Terminate here)