background image
1
KV-C1007
TV Tuner Unit : Instructions
-. : p
LVT1392-001A
[EE]
ENGLISH
0605MNMMDWJEIN
EN, RU
WARNINGS
· USE WITH DC 12 V NEGATIVE GROUND VEHICLES.
If your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC IN-CAR ENTERTAINMENT dealer.
· DO NOT INSTALL THE MONITOR IN A LOCATION WHICH OBSTRUCTS DRIVING AND
VISIBILITY, OR WHERE APPLICABLE LAWS AND REGULATIONS PROHIBIT THE
INSTALLATION.
· NEVER USE BOLTS OR NUTS FROM THE VEHICLE'S SAFETY DEVICES FOR
INSTALLATION.
If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation, it
may cause an accident.
· INSTALL THE ANTENNA IN A PROPER LOCATION.
Be sure to select a location for installation of the antenna so that the antenna is not protruding
beyond the width or the front or back of the vehicle. If it is protruding, it might come into contact
with a pedestrian or other object and cause an accident.
·ATTACH THE WIRES CORRECTLY.
If the wiring is not correctly performed, it may cause a fire or an accident. In particular, be sure
to run and secure the lead wire so that it does not get tangled with a screw or the moving
portion of a seat rail.
To prevent short circuits, it is recommended that you disconnect the battery's negative
terminal and make all electrical connections before installing the unit. If you are not sure how to
install this unit correctly, have it installed by a qualified technician.
·Avoid installing the unit in the following places.
­ Where it would hinder your safety driving.
­ Where it would be exposed to direct sunlight or heat directly from the heater or placed in an
extremely hot place.
­ Where it would be subject to rain, water splashes or excessive humidity.
­ Where it would be subject to dust.
­ Where it would be positioned on an unstable place.
­ Where it could damage the car's fittings.
­ Where proper ventilation would not be maintained, such as under a floor mat.
­ Where it would be located near inflammable objects (since heat is generated inside the unit).
· Handle the Lithium coin battery (product number: CR2025) with care.
­ Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a doctor immediately.
­ Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire.
These behaviors may cause the battery to be overheated, crack or fire.
­ Do not leave the battery with other metallic materials.
Doing this may cause the battery to be overheated or cracked. It may cause a fire.
­ When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery
may be overheated, crack or fire.
­ Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to be overheated or cracked. It may cause a fire.
© 2005 Victor Company of Japan, Limited
Parts list
The following parts are provided with this unit.
After checking them, please set them correctly.
Battery
Remote controller
CR2025
RM-RK510
Diversity antennas with a cleaner
Power cord
AV bus cable
Brackets
Fixing screws--M4 x 8 mm
--M4 x 8
Remote sensor unit with double-faced
adhesive tape
Diversity antenna
Monitor system (separately purchased)
( )
TV tuner unit (in trunk)
- ( )
TV tuner unit (under the passenger's seat)
- ( )
Diversity antenna
KD-AV7001 (separately purchased)
KD-AV7001 ( )
Remote sensor unit
When used with KD-AV7001:
KD-AV7001:
When used with another monitor system:
:
INSTALLATION
· The following illustrations show typical installation.
If you have any questions or require information regarding installation kits, consult your JVC
IN-CAR ENTERTAINMENT dealer or a company supplying kits.
·
"" 12 .
, ,
JVC.
· ,
, ,
.
·
.
,
.
· .
,
­ , .
,
.
· .
. , ,
.
. ,
, .
· :
­ .
­ ;
.
­ , .
­ .
­ .
­ .
­ , , .
­
( ).
· ( : CR2025) .
­ .
, .
­ , , ,
.
, .
­ .
. .
­ ;
, .
­ .
.
.
.
.
· .
JVC , .
KV-C1007[EE]4_RUback.p65
05.6.1, 5:11 PM
1


background image
2
Bracket
Floor
Tapping screws (not supplied)
(
)
Fixing screws--M4 x 8 mm
--M4 x 8
Installing the unit
While mounting the unit, be sure to use the tapping screws (not supplied) of appropriate length
so that they will not damage any parts of the car.
Installing the antenna
Before installing:
· The diversity antenna supplied with this unit is designed specifically for use with JVC TV tuner
unit. (It cannot be connected to the car radio.)
· Do not rub the antenna or the antenna's cable with alcohol, benzine, thinner, gasoline or other
volatile substances.
· Attach to the inside of the car window glass.
· Be sure to wipe the window surface where the antenna will be attached with the cleaner
(supplied) to remove moisture, dirt, dust, wax, oil or other substances. (If there is moisture, oil or
other wet substances on the attachment surface, the attachment tape will not stick well and
easily come off.)
· Identify the exact attachment location and confirm that the adhesive surfaces (antenna base and
attachment parts) will not be placed on a heating wire, glass antenna or wiper motor.
CAUTION
Since there may be legal regulations defining the permissible installation locations for the monitor
system which differ by country or by state, be sure to install the monitor in a location complying
with any such laws.
1 Peel off the cover paper from the antenna base and attach to the surface.
2 Peel off the cover paper from the attachment parts in turn and attach to the surface.
Attachment parts
Antenna base
Peel off the cover paper.
.
· When the attachment surface overlaps with
an electrode
·
Attach the antenna to either the left or right of the electrode.
.
Electrode
Heating wires
· When the attachment surface interferes with a
rear wiper motor or a high-mounted brake light
·
Move the antenna's attachment position upwards to avoid
interference.
,
.
· Installing the antenna cord
·
Install the cord from the antenna to the TV tuner unit through
the interior trim and under the carpet, and secure it using the
cord clampers and mirror mats.
-
.
Peel off the cover paper.
.
Attachment location /
Example of installation, side window
12
Mirror mats (separately purchased)
( )
Cord clampers (separately purchased)
( )
TROUBLESHOOTING
When used with any other monitor system than KD-AV7001.
· TV tuner does not work at all.
* Is the remote sensor unit connected correctly?
· No sound is heard.
* Have you adjusted the volume level on the monitor?
· Picture does not come on the screen.
* Is the correct input selected on the monitor?
· The fuse blows.
* Are the red, yellow, and black leads connected correctly?
·Power cannot be turned on.
* Is the yellow lead connected?
(
) , .
:
· , ,
- JVC. (
.)
· , , ,
.
· .
· , ,
( ), , , ,
, . (
, ,
.)
· ,
( )
, .
, , , ,
,
, .
1 .
2
.
( KD-AV7001).
· - .
*
?
· .
*
?
· .
*
?
· .
*
, ?
· .
*
?
KV-C1007[EE]4_RUback.p65
05.6.1, 5:11 PM
2


background image
3
POWER
AVBUS
AVOUTPUT
VIDEO
L
AUDIO
R
4
1
2
3
3A
REMOTE
SENSOR
RESET
32
1
4
AV OUTPUT
R
L
VIDEO
POWER
AV BUS
AUDIO
TV ANTENNA
TV TUNER UNIT KV-C1007
MULTIMEDIA
DV
D/CDRECEIVER
WITHREMO
VABLE
MONITOR
HIDEAW
A Y
UNIT
AVINPUT
1
L
RAUDIO
FM/
AMANTENNA
POWER
BACKCAMERA
REMOTE
CENTER
SPEAKER
CENTER
SUB
WOOFER
L
R
REAR
L
R
FRONT
VIDEO
AVINPUT
2
L
RAUDIO
VIDEO
TOCHANGER
AVBUS
TOMAIN
UNIT
PREOUT
AUDIO
VIDEO
L
R
AVOUTPUT
REMOTE
SENSOR
RESET
32
1
4
AV OUTPUT
R
L
VIDEO
POWER
AV BUS
AUDIO
TV ANTENNA
TV TUNER UNIT KV-C1007
When used with KD-AV7001:
KD-AV7001:
When used with another monitor system:
:
Remote sensor unit
*1 Use this to protect the cord (not to be pinched with the door, etc.)
*2For controlling KV-C1007 through KD-AV7001, this connection is only required. For other connections,
refer to the manual supplied for KD-AV7001.
*3 Reset the unit after installation is finished by pressing in with a ball-point pen or a similar tool.
Antenna base
Antenna element
Hideaway unit (supplied for KD-AV7001)
( KD-AV7001)
AV bus cable (supplied) *2
(
) *2
Monitor system (separately purchased)
( )
*3
*3
ENGLISH
ELECTRICAL CONNECTIONS
Cord protector *1
*1
Typical Connections
Before connecting:
· Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to
the unit.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Finally connect the wiring harness to the unit.
*1 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise
power cannot be turned on.
*
1 ,
.
2
Ignition switch
Black
Yellow *1
*1
Red
Blue with white stripe
1
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch)
,
( )
Fuse block
*2 Not included with this unit.
*
2
.
To an accessory terminal in the fuse block
To the remote control lead of JVC FM modulator KS-IF200 (for details, refer to the Instructions of KS-IF200).
JVC FM KS-IF200 ( . ,
KS-IF200).
*2
*2
*
1 ( ..)
*
2 KV-C1007 KD-AV7001
. . ,
KD-AV7001.
*
3 ,
.
.
· .
.
1 .
2 .
See "Typical Connections" below.
. " ".
KV-C1007[EE]4_RUback.p65
05.6.1, 5:11 PM
3


background image
4
RM-RK510
Dashboard, etc.
..
Connecting the remote sensor unit
· When used with any other monitor system than KD-AV7001.
· Before installing, make sure the remote controller functions properly with the remote sensor
unit placed in your selected position.
· Wipe clean the selected area sufficiently, and affix the remote sensor unit to the place firmly
after removing the protective sheet from the double-faced adhesive tape.
·Avoid any area on the dashboard, etc. subjected to direct sunlight.
Select an area where the remote sensor unit can receive remote signals through its front face
(sensing area).
Sensing area
Double-faced adhesive tape (supplied)
(
)
1
2
3
4
5
1
2
3
OPERATIONS
The following operations cannot be used when connecting this TV tuner
unit to KD-AV7001.
· When connecting to KD-AV7001, refer to the Instructions supplied with them.
1 Standby/On button
Press to turns on and off the TV tuner unit.
2 TV CH (channel)
5 / button
· Press to search for the TV channels ("SEARCH" appears). When a TV station is received,
search will stop.
· Press and hold to activate manual search ("MANUAL" appears) for the TV station. Then
press repeatedly to change the TV channels.
3 AUTO PRESET button
· Press to display the preset channel list.
· Press and hold to preset the receivable TV stations automatically into the preset number
buttons (1 ­ 12).
4 DISP (display) button
Press to display the preset channel number on the monitor.
5 Preset number buttons (1 ­ 12)
· Press to select the preset channel number directly.
· Press and hold to store a TV station into preset number (1 ­ 12).
CR2025
CAUTION /
DO NOT leave the remote controller in a place (such as
dashboards) exposed to direct sunlight for a long time.
Otherwise, it may be damaged.
,
(,
).
.
SPECIFICATIONS
TV TUNER UNIT
TV antenna jack
× 4
AV bus terminal
× 1
Remote sensor jack
× 1
Output
Video:
RCA pin
× 1; 1 V(p-p), 75
Audio:
RCA pin
× 2; 150 mV(rms)
Dimensions (W
× H × D): 163 mm × 28 mm × 122 mm
Mass: 620 g
DIVERSITY ANTENNANA
Output impedance: 75
× 4 (with mini plug)
Cord length: 5 m
Dimensions (approx.) (W
× H × D): 440 mm × 490 mm × 18 mm (without the cable)
Mass (each unit) (approx.):
220 g (including the cable)
GENERAL
×
Channel coverage
VHF:
ch 1 ­ 12
UHF:
ch 21 ­ 69
Power requirement
Operating voltage: DC 14.4 V (11 V to 16 V allowance)
Grounding system: Negative ground
Allowable operating temperature: 0°C to +40°C
Design and specifications subject to change without notice.
" " () "
, , " (7) . ,
, ,
/ .
, , (2) .
(), , ,
, , JVC, , .
· ( KD-AV7001).
· ,
, .
·
,
.
· - ,
.
,
( ).
-
KD-AV7001.
· KD-AV7001 . .
1 /
-.
2 TV CH
5 / -
· - ( "SEARCH").
- .
· - (
"MANUAL"). -.
3 AUTO PRESET
· .
·
- (1 ­ 12).
4 DISP ()
.
5
(1 ­ 12)
·
.
· - (1 ­ 12).
-
-
× 4
× 1
× 1
: RCA
× 1; 1 V( ), 75
:
RCA
× 2; 150 (.)
(
× × ): 163 × 28 × 122
:620
: 75
× 4 ( -)
:
5
(.) (
× × ):
440
× 490 × 18 ( )
( ) (.):
220 ( )
VHF:
1 ­ 12
UHF:
21 ­ 69
: 14,4 ( 11 16 )
:
: 0°C +40°C
.
KV-C1007[EE]4_RUback.p65
05.6.1, 5:11 PM
4