background image
SERVICE MANUAL
CASSETTE RECEIVER
No.49609
Feb. 2001
COPYRIGHT
2001 VICTOR COMPANY OF JAPAN, LTD.
KS-FX701/KS-FX601
KS-F501
KS-FX701/KS-FX601
KS-F501
Area Suffix
U
Other Areas
Contents
Safety precaution
Disassembly method
Adjustment method
Description of major ICs
1- 2
1- 3
1-12
1-16~24
Difference point
KS-FX701
KS-FX601
KS-F501
O
O
X
LCD
Multi
Nega
Nega
Remocon
O
X
X
Changer
controller


background image
KS-FX701/KS-FX601
KS-F501
1-2
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Safety precaution


background image
KS-FX701/KS-FX601
KS-F501
1-3
Press the eject button in the lower right part of the
front panel. Remove the front panel assembly from
the body.
1.
Removing the front panel assembly
(See Fig.1)
Prior to performing the following procedure, remove
the front panel assembly.
Release the four joint tabs a on both sides of the
front chassis assembly and remove the front chassis
assembly toward the front.
1.
Removing the front chassis assembly
(See Fig.2 and 3)
Disassembly method
<Main body>
Fig.1
Fig.2
Fig.3
Front panel assembly
Eject button
Tab a
Tab a
Front chassis assembly
Front chassis
assembly
Heat sink
Tab a
Tab a


background image
KS-FX701/KS-FX601
KS-F501
1-4
Remove the three screws A on the left side of the
body.
1.
Removing the heat sink (See Fig.4)
Prior to performing the following procedure, remove
the front panel assembly, the front chassis assembly
and the heat sink.
Turn over the body and unjoint the five joints b with
the bottom cover and the body using a screwdriver.
1.
Removing the bottom cover
(See Fig.5 and 6)
Fig.4
Fig.5 (KS-FX601U, KS-FX701U)
Fig.6 (KS-FX601U, KS-FX701U)
Heat sink
A
A
Joints b
Joints b
Joint b
Joints b
Joints b
Joint b
Bottom cover
Bottom cover
Rear panel
Rear panel
Fig.5 (KS-FX501U)
Fig.6 (KS-FX501U)
Joints b
Joints b
Joint b
Joints b
Joints b
Joint b
Bottom cover
Bottom cover
Rear panel
Rear panel


background image
KS-FX701/KS-FX601
KS-F501
1-5
Prior to performing the following procedure, remove
the front panel assembly, the front chassis assembly,
the heat sink and the bottom cover.
Remove the screw B, the five screws C and the two
screws D attaching the rear bracket on the back of
the body. Remove the rear panel.
(KS-FX601U / KS-FX701U)
Remove the screw B, the four screws C and the two
screws D attaching the rear bracket on the back of
the body. Remove the rear panel. (KS-FX501U)
Remove the two screws E attaching the main board
on the bottom of the body. Disconnect connector
CN701 on the main board in the direction of the
arrow.
1.
1.
2.
Removing the main board
(See Fig.7 and 8)
Prior to performing the following procedure, remove
the front panel assembly, the front chassis assembly,
the heat sink, the bottom cover and the main board.
Remove the four screws F
attaching the cassette
mechanism section on the back of the top chassis.
1.
Removing the cassette mechanism section
(See Fig.9)
Fig.7 (KS-FX601U, KS-FX701U)
Fig.8
Fig.9
Rear panel
B
D
D
C
C
Main board
E
E
CN701
Cassette mechanism section
F
F
F
F
Top chassis
C
Fig.7 (KS-FX501U)
Rear panel
B
D
D
C
C
C