background image
1
KS-AX5700
KS-AX5500
POWER AMPLIFIER: INSTRUCTIONS
AMPLIFICATEUR DE PUISSANCE: MANUEL D'INSTRUCTIONS
0605MNMMDWASH
EN, FR
© 2005 Victor Company of Japan, Limited
ENGLISH
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult your "JVC IN-CAR ENTERTAINMENT" car audio dealer or a company
supplying kits.
A Mount on a firm surface, such as in the trunk room or under the front seat.
· Since heat is generated in this unit, do not mount near inflammable objects. In addition,
mount in an area that will not prevent the unit from dissipating heat.
· Do not mount the unit in the places subject to heat such as near a radiator, in a glove
compartment or in insulated areas such as under a car mat that will prevent the unit from
dissipating heat.
B When mounting this unit, be sure to use the screws provided. If any other screws are used,
there is a risk of loosening the unit or damaging parts inside it.
· Before drilling holes in the trunk to install the unit, make sure that there is a sufficient space
under the trunk so that you do not drill holes in the fuel tank, etc.
C After install the unit, attach the terminal cover.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure
your complete understanding and to obtain the best possible performance from the unit.
For safety....
· Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
· Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
· This unit uses BTL (Balanced Trans-formerless) amplifier circuitry, i.e., floating ground system,
so please comply with the following:
Do not connect the "
·" terminals of the speakers to each other.
Do not connect the "
·" terminals of the speakers to the metal body or chassis.
· Cover the unused terminals with insulating tape to prevent them from short circuiting.
· When an extension lead is used, it should be as thick and short as possible; connect it firmly
with insulating tape.
· Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
· When replacing the fuse, only use a 40 A fuse.
· Do not let pebbles, sand or metallic objects get inside the unit.
· To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically.
· Listening to the tape, radio, CD or MD, etc. with the volume on loud for a long period of time will
exhaust the battery, while the engine is turned off or while the engine is idling.
· This unit becomes very hot. Be careful not to touch the unit not only when using but for a while
after using.
DO NOT disassemble the units since there are no user serviceable parts inside.
CAUTION
To prevent short circuits while making connections, keep the battery's negative terminal
disconnected.
· When using a power cord, be sure to place the 40 A fuse near the battery as shown.
· Connect the lead wire (purchased separately) through which power is supplied directly to the
battery's "
ª" terminal only after all the other connections have been made.
The lead wire connected to the + B terminal of this unit should have a cross-section of more
than 8 mm2. Be sure to use a ring terminal (optional) for secure connection.
· If you have any questions regarding the thickness of the power cord, etc., consult your nearest
"JVC IN-CAR ENTERTAINMENT" car audio dealer.
When you use JVC car receiver with a remote lead (a), connect to the REM terminal on this
unit.
When connecting a unit without a remote lead (b), connect to the accessory circuit of the car
which is activated by the ignition switch. In this case, noise may occur when the car receiver is
turned on or off. To avoid this noise, do not turn on or off the car receiver itself. You can turn on or
off the car receiver along with the on/off operation of the ignition switch.
If the POWER/PROTECTOR lamp lights in red, it indicates incorrect speaker wiring or
connections. In normal status, the POWER/PROTECTOR lamp lights in green. Make sure to
correct speaker wiring and other connections.
TERMINAL CONNECTIONS
When making the terminal connections...
Properly fix the terminal with the screw provided by turning it in the
direction as illustrated.
Note
When you tighten the screw, make sure that the screw is securely fixed in
place to prevent disconnection of the terminal. Avoid over-tightening as it
may cause damage to the screw or its head slot.
POWER SUPPLY
LVT1384-001A
[J/E/U]
For Customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
SPEAKER SYSTEMS
This amplifier provides two types of speaker connections: Normal mode and Bridge mode. You
can choose either type of connections depending on the speakers configuration equipped on
your car.
Make sure to comply with the following notes:
· Be sure not to connect the "
·" terminals of the speakers to a common point.
· If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be
used. Always use the independent lead wires for the speakers to be used. In this case, redo the
wirings.
· Use the speakers with an impedance of 2 to 8 (4 to 8 : when used in Bridge mode).
· Use the speakers which have sufficient power to the unit.
A
BC
EN_KS-AX5500&5700[J_E_U]f.indd 1
EN_KS-AX5500&5700[J_E_U]f.indd 1
05.6.30 8:43:11 PM
05.6.30 8:43:11 PM


background image
2
KS-AX5700
L
L
· Depending on the manufacturer and model of the car, speaker wiring may have been finished
when purchased. If the ground wire is common to both left and right speakers, this unit cannot
be used. In this case, redo the speaker wiring.
å When your receiver is equipped with Line Output, connect the Line Output (through the
receiver) to the INPUT jacks on this unit.
When your receiver is NOT equipped with Line Output, connect the speaker connector
(through the receiver) to the HIGH INPUT terminal on this unit.
2-speaker system--BRIDGE MODE
*2
4-speaker system
2-speaker system plus subwoofer--BRIDGE MODE
*2
2-speaker system
2-speaker system (2 amplifiers)--BRIDGE MODE
*2
Subwoofer system--BRIDGE MODE
*2
SPEAKER CONNECTIONS
Connection varies depending on the number of the speakers used in your car. Select the
appropiate connection referring to the diagrams below.
Before connecting: Securely connect all the parts. If the connections are loose, due to contact
resistance etc., heat will break out and may cause an accident. Secure and cover the cords with
insulating tape and run them under the car mats.
KS-AX5500
*1 Not supplied for this unit.
*2 BRIDGE MODE: Be sure to connect the line output from the receiver to the left (L) jack on this
unit.
*3 Be sure to connect the both leads to the target speaker lead.
EN_KS-AX5500&5700[J_E_U]f.indd 2
EN_KS-AX5500&5700[J_E_U]f.indd 2
05.6.30 8:43:15 PM
05.6.30 8:43:15 PM


background image
3
SPECIFICATIONS
Power Output
KS-AX5700: 200 W RMS x 2 channels at 4 and 1% THD + N
KS-AX5500: 100 W RMS x 4 channels at 4 and 1% THD + N
Signal-to-Noise Ratio
80 dBA (reference: 1 W into 4 )
TROUBLESHOOTING
For more details, consult your "JVC IN-CAR ENTERTAINMENT" car audio dealer.
The POWER/PROTECTOR lamp does not light.
· Confirm if the fuse is blown.
· Confirm if the ground lead is connected securely to a metal part of the car.
· Make sure that the equipment connected to this unit is turned on.
· Use a relay if your system employs too many amplifiers.
· Confirm the battery voltage (11 V to 16 V).
The POWER/PROTECTOR lamp lights in red and/or the unit heats up abnormally.
· Confirm if the impedance of the connected speaker is suitable.
· Confirm if the speaker wirings are short-circuited.
· Leave the unit turned off for a while as it cools down.
No sound is heard.
· Confirm if the POWER/PROTECTOR lamp lights in green (see "POWER SUPPLY" on page 1).
· Is the remote turn-on line lead connected correctly?
· Are RCA pin cords connected to the INPUT jacks?
· Is the speaker input connector from the receiver connected to the HIGH INPUT terminal?
· Is this amplifier grounded?
Alternator noise is heard.
· Keep the power connecting leads away from the RCA pin cords.
· Keep the RCA pin cords away from other electrical cables in the car.
· Confirm if the ground lead is connected securely to a metal part of the car.
· Confirm if the negative speaker leads are touching the car chassis.
· Confirm if the noise originates in the receiver.
· Replace the plugs or use plugs with load resistors.
· Connect a bypass capacitor across the accessory switches (horn, fan, etc.).
Noise when connected to AM (MW/LW) tuner.
· Move the speaker and power leads away from the antenna (aerial) lead.
CONTROLS
KS-AX5700
Control Panel cover
To operate the following controls, remove the bolts with a hex wrench
BASS BOOST controller
Turning this enables boosting of the 45 Hz frequency within a range of 0 dB to +12 dB. Adjust
the level while listening to the sound. This control is preset to the middle of this range at the
factory.
Input LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source
equipments. Turn it in the clockwise direction when the output level of the car audio seems
low.
FREQUENCY controller
Turning this enables adjustment of the frequency cut-off point through the filter within a range
of 50 Hz to 300 Hz. Adjust the level while listening to the sound. This control is preset to the
middle of this range at the factory.
CROSSOVER filter switch
OFF: Normally, set to this position. (Preset to this position at the factory.)
LPF: Set to this position when you want to turn on the LPF (Low-pass filter) switch. You can
use the following terminals for a subwoofer system.
KS-AX5500: REAR SPEAKER OUTPUT
KS-AX5700: SPEAKER OUTPUT
HPF: Set to this position when you want to turn on the HPF (High-pass filter) switch. The
low frequency signals are not applied to the left/right speaker when a subwoofer is
connected.
KS-AX5500
Maximum Power Output
KS-AX5700: 900 W
KS-AX5500: 800 W
Load Impedance
4 (2 to 8 allowance)
4 (4 to 8 allowance) (Bridge mode)
Frequency Response
5 Hz to 50,000 Hz (+0, ­3 dB)
Input Sensitivity/Impedance
1 V/20 k (0.3 V to 6 V, variable)
Distortion
Less than 0.04% (at 1 kHz)
Power Requirement
DC 14.4 V (11 V to 16 V allowance)
Grounding system
Negative ground
Dimensions (W/H/D)
400 mm × 264 mm × 63 mm
(15-3/4 in. × 10-7/16 in. × 2-1/2 in.)
Mass (approx.)
5.7 kg (12.6 lbs.)
Supplied Accessories
Speaker input connector × 2 (KS-AX5500)
× 1 (KS-AX5700)
Mounting Screw ( 4.0 × 20 mm (13/16 in.)) × 4
Terminal cover × 1
Hex bolt × 2
Hex wrench × 1
Design and specifications are subject to change without notice.
EN_KS-AX5500&5700[J_E_U]f.indd 3
EN_KS-AX5500&5700[J_E_U]f.indd 3
05.6.30 8:43:16 PM
05.6.30 8:43:16 PM


background image
1
FRANÇAIS
INSTALLATION
L'illustration suivante est un exemple d'installation typique. Cependant, vous devez faire les
ajustements correspondant à votre voiture particulière. Si vous avez des questions ou avez
besoin d'information sur des kits d'installation, consulter votre revendeur d'autoradios JVC ou
une compagnie d'approvisionnement.
A Montez sur une surface solide, telle que le plancher du coffre arrière ou sous le siège avant.
· Comme cet appareil génère de la chaleur, ne le montez pas près d'objets inflammables.
De plus, choisissez un endroit où rien ne gênera la bonne dissipation de la chaleur de
l'appareil.
· Ne montez pas l'appareil dans un endroit sujet à la chaleur, comme près d'un radiateur,
dans la boîte à gants ou dans un endroit fermé tel que sous un tapis de sol, qui empêchera
la bonne dissipation de la chaleur.
B Lors du montage de cet appareil, assurez-vous d'utiliser les vis fournies. Si vous
utilisez d'autres vis, l'appareil risque de se déserrer et des pièces internes peuvent être
endommagées.
· Avant de percer des trous dans le coffre pour installer l'appareil, s'assurer qu'il y a un
espace suffisant sous le coffre pour ne pas faire de trous dans le réservoir de carburant, etc.
C Après avoir installé l'appareil, fixez le couvercle des prises.
Merci pour avoir acheté un produit JVC. Veuillez lire attentivement toutes les instructions avant d'utiliser
l'appareil afin de bien comprendre son fonctionnement et d'obtenir les meilleures performances possibles.
Pour votre sécurité....
· N'augmentez pas trop le niveau du volume car cela peut bloquer les sons de l'extérieur et
rendre la conduite dangereuse.
· Arrêtez la voiture avant de réaliser une opération compliquée.
ATTENTION ET REMARQUES
Cet appareil est conçu pour fonctionner avec système électrique de 12 V CC avec mise à la
masse NÉGATIVE.
· Cet appareil utilise un circuit d'amplification BTL (symétrique sans transformateur), c'est à dire
un système à masse flottante par conséquent veuillez vous conformer à ce qui suit:
Ne connectez pas les prises "
·" des enceintes l'une à l'autre.
Ne connectez pas les prises "
·" des enceintes au corps métallique ou au châssis.
· Recouvrir les bornes inutilisées avec du ruban isolant pour éviter de les court-circuiter.
· Si vous utilisez un fil de prolongement, celui-ci doit être aussi épais et aussi court que possible.
Connectez-le solidement avec un ruban adhésif.
· Bien laisser un espace suffisant entre I'antenne et les fils de cet appareil.
· Lors du remplacement du fusible, utilisez uniquement un fusible de 40 A.
· Ne pas laisser pénétrer de cailloux, de sable ou d'objets métalliques dans I'appareil.
· Pour que le mécanisme de dissipation de la chaleur fonctionne effectivement, essuyer
régulièrement la poussière qui s'accumule.
· Écouter une cassette, la radio, un CD ou un MD, etc. avec un volume très fort, pendant une
longue période, quand le moteur est coupé ou est au ralenti, déchargera la batterie.
· Cet appareil devient très chaud. Faites attention de ne pas le toucher pendant son utilisation
mais aussi après sont utilisation.
NE DEMONTEZ PAS l'appareil. Il n'y a aucune pièce réparable par l'utilisateur à l'ntérieur.
ATTENTION
Pour éviter les courts-circuits lors des connexions, laissez la borne négative de la batterie
débranchée.
· Si vous utilisez un cordon d'alimentation, assurez-vous de placez le fusible de 40 A aussi près
de la batterie que possible.
· Connectez le fil d'alimentation (à acheter séparément), à travers lequel l'alimentation est
fournie, directement à la borne "
ª" de la batterie uniquement après que toutes les autres
connexions sont terminées.
Le fil conducteur raccordé à la borne + B de cet appareil doit avoir une section de plus de
8 mm2. Bien utiliser une cosse (en option) pour des raccordements sûrs.
· Si vous avez des questions concernant la grosseur du cordon d'alimentation, etc., consulter
votre revendeur d'autoradios JVC le plus proche.
Si vous utilisez un autoradio JVC muni d'un fil de télécommande (a), connectez à la prise
REM de cet appareil.
Si vous utilisez un autoradio JVC sans fil de télécommande (b), connectez au circuit
accessoire de la voiture qui est mis sous tension avec le commutateur d'allumage. Dans ce cas,
du bruit peut se produire quand l'autoradio est mis sous ou hors tension. Pour éviter ce bruit, ne
mettez pas directement l'autoradio sous ou hors tension. Vous pouvez le mettre sous ou hors
tension en même temps que le commutateur d'allumage de votre voiture.
Si le témoin POWER/PROTECTOR s'allume en rouge, cela signifie que le câblage des
enceintes ou les connexions sont incorrects. Dans un état normal, le témoin POWER/
PROTECTOR est allumé en vert. Assurez-vous que le câblage des enceintes et les autres
connexions sont corrects.
CONNEXIONS DES PRISES
Lors de la réalisation de la connexion des prises...
Fixez correctement chaque prise avec la vis fournie en le tournant
dans la direction montrée sur l'illustration.
Remarque
Quand vous serrez la vis, assurez-vous de la serrer solidement de façon à
éviter toute déconnexion au niveau de la prise. Évitez aussi de trop serrer
car cela peut endommager la vis ou la tête de la vis.
ALIMENTATION
SYSTÉMES D'ENCEINTES
Cet amplificateur est muni de deux types de connexion d'enceinte: un mode normal et un mode
en pont. Vous pouvez choisir n'importe quel type de connexion en fonction de la configuration
des enceintes qui équipent votre voiture.
Assurez-vous de respecter les points suivants:
· Ne pas raccorder les bornes "
·" des haut-parleur à un point commun.
· Si le fil de masse est commun aux câblages des enceintes gauche/droite et avant/arrière, cet
appareil ne peut pas être utilisé. Utilisez toujours des fils de masse indépendants pour chaque
enceinte utilisée. Refaites les câblages si nécessaire.
· Utilisez des enceintes avec une impédance comprise entre 2 et 8 (4 et 8 : lors de
l'utilisation du mode de connexion en pont).
· Utilisez des enceintes suffisamment puissantes pour l'appareil.
A
BC
FR_KS-AX5500&5700[J_E_U]2.indd 1
FR_KS-AX5500&5700[J_E_U]2.indd 1
05.7.7 6:52:33 PM
05.7.7 6:52:33 PM


background image
2
KS-AX5700
· Sur certaines marques et certains modèles de voiture, le câblage des enceintes est déjà
réalisé à l'achat. Si le fil de masse est commun aux enceintes gauche et droite, cet appareil ne
peut pas être utilisé. Dans ce cas, refaites le câblage des enceintes.
å Si votre récepteur est muni d'une sortie de ligne, connectez la sortie de ligne (à travers le
récepteur) aux prises INPUT de cet appareil.
Si votre autoradio N'EST PAS muni d'une sortie de ligne, connectez le connecteur
d'enceinte (à travers l'autoradio) à la prise HIGH INPUT sur cet appareil.
Système à 2 enceintes--BRIDGE MODE (Mode en pont)
*2
Système à 4 enceintes
Système à 2 enceintes plus un caisson de grave--BRIDGE MODE (Mode en pont)
*2
Système à 2 enceintes
Système à 2 enceintes (2 amplificateurs)--BRIDGE MODE (Mode en pont)
*2
Système de caisson de grave--BRIDGE MODE (Mode en pont)
*2
CONNEXION DES ENCEINTES
La connexion varie en fonction du nombre d'enceintes utilisées dans votre voiture. Choisissez la
connexion la plus appropriée en vous référant aux illustrations ci-dessous.
Avant de commencer la connexion: Connectez solidement toutes les pièces. Si les connexions
sont lâches, à cause de la résistance des contacts, etc., de la chaleur peut se dégager et causer un
accident. Fixez et recouvrez les fils avec un ruban isolant et faites-les passer sous les tapis de sol.
KS-AX5500
*1 Non fourni avec cet appareil.
*2 BRIDGE MODE (Mode en pont): Assurez-vous de connecter la sortie de ligne de l'autoradio à
la prise gauche (L) de cet appareil.
*3 Assurez-vous de connecter les deux fils au fil de l'enceinte cible.
FR_KS-AX5500&5700[J_E_U]2.indd 2
FR_KS-AX5500&5700[J_E_U]2.indd 2
05.7.7 6:52:37 PM
05.7.7 6:52:37 PM