background image
SERVICE MANUAL
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LIMITED
No.49831
2003/5
CD RECEIVER
49831
2003
5
KD-SH9750,KD-SH9700
TABLE OF CONTENTS
1
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
Disassembly method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3
Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28
4
Description of major ICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
Area Suffix
KD-SH9750
J -------------------------- U.S.A.
C --------------------- CANADA
Area Suffix
KD-SH9700
J -------------------------- U.S.A.
Detachable
ANGLE
RM-RK100
CD
FM
AM
CH
AUX
SEL
VOLUME
R D
ATT
DAB
DISC
PRESET
PRESET
DISC
EQ
3456
M
2
1
D
SRC
DISP
ATT
SEL
BBE
MODE
KD-SH9750J
ARSENAL rogo
Line output level
WARRANTY
2 YEAR
1 YEAR
1 YEAR
4 V
4 V
2 V
KD-SH9750C KD-SH9700J


background image
1-2 (No.49831)
SPECIFICATION
Design and specifications are subject to change without notice.
If a kit is necessary for your car consult your telephone directory for the nearest car audio speciality shop.
AUDIO
AMPLIFIER
SECTION
Maximum Power Output
Front
50 W per channel
Rear
50 W per channel
Continuous Power Output (RMS)
Front
19 W per channel into 4
, 40 Hz to
20,000 Hz at no more than 0.8% total
harmonic distortion.
Rear
19 W per channel into 4
, 40 Hz to
20,000 Hz at no more than 0.8% total
harmonic distortion. 0.8% total
harmonic distortion.
Load Impedance
4
(4 to 8 allowance)
Equalizer Control Range
Frequencies
60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz,
6 kHz, 12 kHz
Level
±10 dB
Frequency Response
40 Hz to 20,000 Hz
Signal-to-Noise Ratio
70 dB
Line-In Level/Impedance (KD-SH9750 only) LINE IN
1.5 V/20 k
load
Line-Out Level/Impedance
KD-SH9750
4.0 V/20 k
load (full scale)
KD-SH9700
2.0 V/20 k
load (full scale)
Output Impedance
1 k
TUNER
SECTION
Frequency Range
FM
87.5 MHz to 107.9 MHz (with channel
interval set to 200 kHz) 87.5 MHz to
108.0 MHz (with channel interval set to
50 kHz)
AM
530 kHz to 1 710 kHz (with channel
interval set to 10 kHz) 531 kHz to 1 602
kHz (with channel interval set to 9 kHz)
[FM Tuner]
Usable Sensitivity
11.3 dBf (1.0
µV/75 )
50 dB Quieting Sensitivity
16.3 dBf (1.8
µV/75 )
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response
40 Hz to 15,000 Hz
Stereo Separation
35 dB
Capture Ratio
1.5 dB
[AM Tuner]
Sensitivity
20
µV
Selectivity
35 dB
CD
PLAYER
SECTION
Type
Compact disc player
Signal Detection System
Non-contact optical pickup (semiconductor laser)
Number of channels
2 channels (stereo)
Frequency Response
5 Hz to 20,000 Hz
Dynamic Range
98 dB
Signal-to-Noise Ratio
102 dB
Wow and Flutter
Less than measurable limit
MP3 (MPEG Audio Layer 3)
Max. Bit rate
320 Kbps
WMA (Windows Media(R) Audio) Max. Bit rate
192 Kbps
GENERAL
Power Requirement
Operating Voltage
DC 14.4 V (11 V to 16 V allowance)
Grounding System
Negative ground
Allowable Operating Temperature
0
°C to +40°C (32°F to 104°F)
Dimensions (W x H x D)
Installation Size
182 mm x 52 mm x 161 mm
(7-3/16" x 2-1/16" x 6-3/8")
Panel Size
188 mmx 58 mm x 17 mm
(7-7/16" x 2-5/16" x 11/16")
Mass
1.8 kg (4.0 lbs) (excluding accessories)


background image
(No.49831)1-3
SECTION 1
Precautions
1.1
Safety Precautions
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
!
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.


background image
1-4 (No.49831)
1.2
Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1
Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup
· In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
· Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3
Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4
Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
· Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CDpickup may be destroyed by static electricity.)
· In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
1M
(caption)
Anti-static wrist strap
Conductive material
(conductive sheet) or iron plate
Pickup
Short-circuit point
(Soldering)
Flexible wire
Pickup
Short-circuit point


background image
(No.49831)1-5
SECTION 2
Disassembly method
2.1
Main body section
2.1.1 Removing the front panel assembly (See Fig.1)
(1) Push the detach button in the lower right part of the front
panel assembly.
(2) Remove the front panel assembly in the direction of the
arrow.
Fig.1
Front panel assembly
Detach button