background image
INSTRUCTIONS
IF-C01COMG Component/RGB Input Card
IF-C01PNG Video Input Card
IF-C01SDG SDI Input Card
INPUT CARD FOR A JVC MULTI-FORMAT MONITOR
BEDIENUNGSANLEITUNG : EINGANGSKARTE FÜR JVC MULTI-
SYSTEM-MONITORE
MANUEL D'INSTRUCTIONS : CARTE D'ENTRÉE POUR MONITEURS
MULTI-FORMAT JVC
MANUALE DI ISTRUZIONI : SCHEDA DI INGRESSO PER MONITOR
MULTIFORMATO JVC
INSTRUCCIONES
: TARJETA DE ENTRADA PARA UN
MONITOR MULTIFORMAT JVC
!"
: gs`
!"#$%&'(
LCT0972-002A
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
R


background image


background image
ENGLISH
INSTRUCTIONS
INPUT CARD FOR A JVC
MULTI-FORMAT MONITOR
IF-C01COMG Component/RGB Input Card
IF-C01PNG Video Input Card
IF-C01SDG SDI Input Card
Before installing this Input Card in your monitor, please read the Safety
Precautions included in your monitor's user manual.
This product is designed exclusively for professional use. Only qualified
technicians or individuals with the appropriate technical knowledge should
perform installation.
FCC NOTICE (U.S.A. only)
CAUTION: Changes or modifications not approved by JVC could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Thank you for purchasing this JVC Input Card. In order to take full advantage of the
card's capabilities, please read and follow all instructions carefully before installing
and using the card. Retain this booklet for future reference.
EMC Supplement (Europe only)
This equipment is in conformity with the provisions and protection requirements of the corresponding
European Directives. This equipment is designed for professional video appliances and can be used
in the following environments:
Controlled EMC environment (for example purpose built broadcasting or recording studio), and
the rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)


background image
INSTALLATION
The same installation procedure applies to all Input Cards.
If the Input Card is installed correctly, your Multi-Format Monitor will automatically
recognise it.
Refer to the user manual provided with your Multi-Format Monitor for details on adjustment
or setting of input signals via the Input Card.
PREPARATION
· Wear gloves to protect your hands from metal parts on the Input Card's board.
· You will need a 6-mm Phillips screwdriver.
· Turn off the Multi-Format Monitor's main power and unplug the power cable from the AC outlet.
CAUTIONS
· Do not touch the terminal connected to the monitor or board pattern. (Doing so may produce static
electricity that will damage the Input Card.)
· Do not remove slot covers from the monitor's slots if they are not in use.
· Do not force the Input Card into the monitor's slot.
INSTALLATION PROCEDURE
1. Unscrew the screws and remove
the slot cover from the slot (on the
rear side of the monitor) in which
you are going to install the card.
2. Inser t the Input Car d's board
(green-coloured) into the slot,
fitting the board into the guide
rails on the top and bottom of the
slot.
3. Push the Input Card in so that its
fr ont panel touches the monitor' s
rear panel. (Insert the Input Card
holding the knobs at the top and
bottom.)
4. Secure the Input Card by replacing
the screws removed in Procedure
1.
Make sure the Input Card is correctly
installed by checking "SLOT CONDITION"
in the Main Menu of the Multi-Format
Monitor. (Also refer to the Multi-Format
Monitor's instruction manual.)
Slot cover
Fit the board to
the guide rails.
Knob
Rear side of the multi-format
monitor
Knob
Input card (the
illustration shown is
of the IF-C01PNG)
Guide rails
2


background image
ENGLISH
IF-C01SDG: SDI INPUT CARD
Type
: SDI input card for multi-format monitor
Inputs/Outputs
: Digital input (SDI 1/SDI 2): 2 lines, BNC connector x 2
(0.8 V (p-p), 75
)
Digital output (SWITCHED OUT): 1 line, BNC connector x 1
(0.8 V (p-p), 75
)
Audio signal: 2 lines (monaural), RCA pin x 4 (0.5 V (rms),
high impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.
Format
: D1 serial component digital, 525/625 auto switching (compliant to
SMPTE259M)
Required slots
:1
Power
consumption
: 7 V DC, 0.65 A
Weight
: 0.5 k
g
Dimensions
(W x H x D)
: 43 mm x 154.5 mm x 191.9 mm
IF-C01PNG: VIDEO INPUT CARD
Type
: Video input card for multi-format monitor
Inputs/Outputs
: VIDEO 1/VIDEO 2: 2 lines, BNC connector x 4 (1 V (p-p), 75
)
Synchronised signal (EXT.SYNC): 1 line, BNC connector x 2
(1.0 V ­ 4.0 V (p-p), 75
)
* The input (IN) and output (OUT) terminals are bridge-connected.
Auto termination.
Y/C signal: 1 line, input only, mini-DIN 4-pin connector x 1 (Y/C
input has a priority to a VIDEO 2 input) (Y: 1 V (p-p),
75
/C: 0.286 V (NTSC (3.58 MHz))/0.3 V (PAL
(4.43 MHz)), 75
)
Audio signal: 2 lines (monaural), RCA pin x 4 (0.5 V (rms), high
impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.
Required slots
:1
Power
consumption
: 14 V DC, 0.25 A
7 V DC, 0.15 A
Weight
: 0.5 k
g
Dimensions
(W x H x D)
: 43 mm x 154.5 mm x 191.9 mm
SPECIFICATIONS
IF-C01COMG: COMPONENT/RGB INPUT CARD
Type
: Component/RGB input card for multi-format monitor
Inputs/Outputs
: Component (Y, PB/B-Y, PR/R-Y) or RGB: 1 line, BNC connector x 6
(Y: 1 V (p-p), 75
/PB, B-Y, PR, R-Y, R, G, B: 0.7 V (p-p), 75 )
Synchronised signal (HD/CS, VD) : 1 line, BNC connector x 4
(1.0 V ­ 4.0 V (p-p), 75
)
* The input (IN) and output (OUT) terminals are bridge-connected.
Auto termination.
Audio signal: 1 line (monaural), RCA pin x 2 (0.5 V (rms), high
impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.
Required slots
:1
Power
consumption
: 14 V DC, 0.02 A
Weight
: 0.5 k
g
Dimensions
(W x H x D)
: 43 mm x 154.5 mm x 191.9 mm
B/PB/B-Y
G/Y
OUT
IN
OUT
IN
R/PR/B-Y
OUT
IN
VD
OUT
IN
HD/CS
OUT
IN
OUT
IN
AUDIO
OUT
IN
VIDEO1
OUT
IN
AUDIO2
AUDIO1
OUT
IN
VIDEO2
OUT
Y/C IN
IN
OUT
IN
EXT.SYNC
AUDIO2
AUDIO1
OUT
IN
SWITCHED
OUT
SDI 1
SDI 2
IN
IN
3