background image
SERVICE MANUAL
COPYRIGHT © 2004 Victor Company of Japan, Limited.
No.YA092B
2004/8
REAR PROJECTION TELEVISION
52096
2003
02
HD-52Z575,
HD-52Z585,
HD-61Z575,
HD-61Z585
TABLEOFCONTENTS
1
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
4
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
BASIC CHASSIS
RP2
REVISED


background image
1-2 (No.YA092B)
SPECIFICATION
Design & specifications are subject to change without notice.
Items
Contents
HD-52Z575
HD-52Z585
HD-61Z575
HD-61Z585
Dimensions (W x H x D)
126.4cm x 91.4cm x 41.2cm
(49-7/8" x 36 x 16-1/4")
145.6cm x 104.2cm x 47cm
(57-3/8" x 41 x 18-1/2")
Mass
37.8kg (84lbs)
44.3kg (98lbs)
TV RF System
CCIR (M)
Color System
NTSC
Sound System
BTSC (Multi Channel Sound)
Teletext System
Closed Caption (T1-T4 / CC1-CC4)
TV Receiving
Channels and
Frequency
VHF Low
VHF High
UHF
54MHz~88MHz (02ch~06ch)
174MHz~216MHz (07ch~13ch)
470MHz~806MHz (14ch~69ch)
CATV 54MHz~804MHz
Low Band : 02~06 by 02~06
High Band : 07~13 by 07~13
Mid Band : A~I by 14~22
Super Band : J~W by 23~36
Hyper Band : W+1~W+28 by 37~64
Ultra Band : W+29~W+84 by 65~94, 100~125
Sub Mid Band : A-8, A-4~A-1 by 01, 96~99
TV / CATV Total Channel
180 Channels
Intermediate
Frequency
Video IF
Sound IF
45.75MHz
41.25MHz (4.5MHz)
Color Sub Carrier
3.58MHz
Power Input
AC120V, 60Hz
Power Consumption
195W (Max)
Projection Source
110W High-pressure mercury lamp
Projection Device
D-ILA device (Reflection active matrix type LCD) x 3(R / G /B)
Resolution
Total=H:1312 x V:800 [ Effective =H:1280 x V:720 ]
Screen
Transparent screen (unitized fresnel lens / lenticular lens), aspect ratio 16:9
Screen Size
52" (132cm) Measured diagonally
H:115.1cm(45-3/8") x V:64.8cm(25-5/8")
61" (155cm) Measured diagonally
H:135cm(53-1/4") x V:76cm(30")
Speaker
10cm round x 2 (Oblique corn)
Audio Power Output
10W+10W
Antenna Terminal (VHF/UHF)
75
unbalanced, coaxial, F-type connector x 1
External Input
[INPUT-1/2/3/4]
Video
Audio
1V(p-p), 75
, negative sync (RCA pin jack x 4)
500mV(rms) (-4dBs), high impedance (RCA pin jack x 8)
S-Video
[INPUT-1/3/4]
Mini-DIN 4pin connector x 3
Y: 1V(p-p), positive, 75
, negative sync
C: 0.286V(p-p) (burst signal)
Component Video
[INPUT-1/2]
720p/1080i
480p/480i
RCA pin jack x 6
Y: 1V(p-p), (Sync signal : ±0.35V, 3-value sync.), 75
Pb/Pr : ±0.35V, 75
Y: 1V(p-p), positive (negative sync), 75
Pb/Pr : 0.7V(p-p), 75
Digital Input
Video
Audio
HDMI connector x 1
(This Digital-in terminal is not compatible with picture signals of personal computer.)
HDMI connector
Digital : HDMI connector
Analog : 500mV(rms) (-4dBs), high impedance (RCA pin jack x 2)
Audio Output (VARI/FIX)
VARI : More than 0 to 1000mV(rms) (+2.2dBs)
FIX : 500mV(rms) (-4dBs), low impedance (1kHz when modulated 100%)
(RCA pin jack x 2)
Sub woofer Output
More than 0 to 1000mV(rms) (+2.2dBs) (RCA pin jack x1)
Center channel Input
500mV(rms) (-4dBs), high impedance (RCA pin jack x1)
AV Compulink lll
3.5mm mini jack x 1
Remote Control Unit
RM-C15G (AA/R6/UM-3 battery x 2)


background image
(No.YA092B)1-3
SECTION 1
PRECAUTIONS
1.1 SAFETY PRECAUTIONS
(1) The design of this product contains special hardware, many circuits
and components specially for safety purposes. For continued
protection, no changes should be made to the original design unless
authorized in writing by the manufacturer. Replacement parts must
be identical to those used in the original circuits. Service should be
performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should not be
made. Any design alterations or additions will void the manufacturer's
warranty and will further relieve the manufacturer of responsibility for
personal injury or property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have special
safety-related characteristics. These characteristics are often not
evident from visual inspection nor can the protection afforded by them
necessarily be obtained by using replacement components rated for
higher voltage, wattage, etc. Replacement parts that have these
special safety characteristics are identified in the parts list of Service
manual. Electrical components having such features are
identified by shading on the schematics and by ( ) on the parts
list in Service manual. The use of a substitute replacement which
does not have the same safety characteristics as the recommended
replacement part shown in the parts list of Service manual may cause
shock, fire, or other hazards.
(4) Use isolation transformer when hot chassis.
The chassis and any sub-chassis contained in some products are
connected to one side of the AC power line. An isolation transformer
of adequate capacity should be inserted between the product and the
AC power supply point while performing any service on some
products when the HOT chassis is exposed.
(5) Don't short between the LIVE side ground and ISOLATED
(NEUTRAL) side ground or EARTH side ground when repairing.
Some model's power circuit is partly different in the GND. The
difference of the GND is shown by the LIVE : ( ) side GND, the
ISOLATED(NEUTRAL) : ( ) side GND and EARTH : ( ) side GND.
Don't short between the LIVE side GND and ISOLATED(NEUTRAL)
side GND or EARTH side GND and never measure with a measuring
apparatus
(oscilloscope
etc.)
the
LIVE
side
GND
and
ISOLATED(NEUTRAL) side GND or EARTH side GND at the same
time.
If above note will not be kept, a fuse or any parts will be broken.
(6) The high voltage applied to the picture tube must conform with that
specified in Service manual. Excessive high voltage can cause an
increase in X-Ray emission, arcing and possible component damage,
therefore operation under excessive high voltage conditions should
be kept to a minimum, or should be prevented. If severe arcing
occurs, remove the AC power immediately and determine the cause
by visual inspection (incorrect installation, cracked or melted high
voltage harness, poor soldering, etc.). To maintain the proper
minimum level of soft X-Ray emission, components in the high
voltage circuitry including the picture tube must be the exact
replacements or alternatives approved by the manufacturer of the
complete product.
(7) If any repair has been made to the chassis, it is recommended that
the B1 setting should be checked or adjusted (See ADJUSTMENT
OF B1 POWER SUPPLY).
(8) Do not check high voltage by drawing an arc. Use a high voltage
meter or a high voltage probe with a VTVM. Discharge the picture
tube before attempting meter connection, by connecting a clip lead to
the ground frame and connecting the other end of the lead through a
10k
2W resistor to the anode button.
(9) When service is required, observe the original lead dress. Extra
precaution should be given to assure correct lead dress in the high
voltage circuit area. Where a short circuit has occurred, those
components that indicate evidence of overheating should be
replaced. Always use the manufacturer's replacement components.
(10) Isolation Check
(Safety for Electrical Shock Hazard) After re-assembling the
product, always perform an isolation check on the exposed metal
parts of the cabinet (antenna terminals, video/audio input and output
terminals, Control knobs, metal cabinet, screwheads, earphone jack,
control shafts, etc.) to be sure the product is safe to operate without
danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal
parts exposed to the user, particularly any exposed metal part
having a return path to the chassis should withstand a voltage
of 1100V AC (r.m.s.) for a period of one second.
(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance
rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated
200V or more, for a period of one second.)
This method of test requires test equipment not generally
found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use a
line isolation transformer during this check.). Using a "Leakage
Current Tester", measure the leakage current from each
exposed metal part of the cabinet, particularly any exposed
metal part having a return path to the chassis, to a known good
earth ground (water pipe, etc.). Any leakage current must not
exceed 0.5mA AC (r.m.s.). However, in tropical area, this must
not exceed 0.2mA AC (r.m.s).
· Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not use
a line isolation transformer during this check.). Use an AC
voltmeter having 1000
per volt or more sensitivity in the
following manner. Connect a 1500
10W resistor paralleled
by a 0.15µF AC-type capacitor between an exposed metal
part and a known good earth ground (water pipe, etc.).
Measure the AC voltage across the resistor with the AC
voltmeter. Move the resistor connection to each exposed
metal part, particularly any exposed metal part having a
return path to the chassis, and measure the AC voltage
across the resistor. Now, reverse the plug in the AC outlet
and repeat each measurement. Any voltage measured
must not exceed 0.75V AC (r.m.s.). This corresponds to
0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.3V AC
(r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
(11) High voltage hold down circuit check.
After repair of the high voltage hold down circuit, this circuit shall be
checked to operate correctly.
See item "How to check the high voltage hold down circuit".
AC VOLTMETER
(HAVING 1000 /V,
OR MORE SENSITIVITY)
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
1500 10W
0.15 F AC-TYPE
GOOD EARTH GROUND
PWB
White line side
WHT
PW
POWER CORD
REPLACEMENT WARNING.
Connecting the white line side of power
cord to "WHT" character side.
A
V
This mark shows a fast
operating fuse, the
letters indicated below
show the rating.


background image
1-4 (No.YA092B)
1.2 INSTALLATION
1.2.1 HEAT DISSIPATION
If the heat dissipation vent behind this unit is blocked, cooling
efficiency may deteriorate and temperature inside the unit will
rise. The temperature sensor that protects the unit will be
activated when internal temperature exceeds the predetermined
level and power will be turned off automatically.
Therefore, please make sure pay attention not to block the heat
dissipation vent as well as the ventilation outlet behind the unit
and ensure that there is room for ventilation around it.
Do not put foreign objects near the ventilation holes as
this can result in fire or electrical hazards.
Do not block the ventilation holes as this may cause the
internal temperature to rise and possibly result fire.
1.2.2 INSTALLATION REQUIREMENTS
Ensure that the minimal distance is maintained, as specified
below, between the unit with and the surrounding walls, as well
as the floor etc.
Install the unit on stable flooring.
Take precautionary measures to prevent the unit from tipping in
order to protect against accidents and earthquakes.
CAUTION FOR INSTALLATION
· Do not tilt the TV towards the left or right, or toward the back.
· Install the TV in a corner on the floor so as to keep cords out
of the way.
· The TV will generate a slight amount of heat during operation.
Ensure that sufficient space is available around the TV to
allow satisfactory cooling.
OFF ON
Intake hole
Exhaust hole
VENTILATION POSITION
200mm
200mm
150mm
50mm
150mm


background image
(No.YA092B)1-5
1.3 LAMP UNIT HANDLING CAUTION
1.3.1 PRECAUTION FOR LAMP UNIT
Thelampemitshighintensitywhite,ultravioletandinfrared
light. Do not look directly at the light during service.
Also, do not touch the lamp directly as it presents a burn
hazard.
Handle with extra care. This lamp emits high heat and
contains high-pressure during use.
Do not give any impact as this may cause the broken lamp.
1.3.2 HOW TO CONFIRM LAMP OPERATING TIME
(1) Set to 0 minutes using the [SLEEP TIMER] key.
(2) Press the [VIDEO STATUS] key and [DISPLAY] key
simultaneously, then enter the SERVICE MODE.
(3) When the Main Menu is displayed, press [4] key to enter
the setting display for designing.
(4) Press [CH+] / [CH-] key to select the addresses (items).
NOTE :
· Confirmation of the information can be done by selecting
addresses (items) below.
Display position is in the far right side in the 2nd row from
the top, as displayed below.
1.3.3 LAMP OPERATING TIME
· MAXIMUM COUNT TIME : 65535 hours
1.3.4 LAMP UNIT REPLACEMENT
(1) The lamp replacement message will appear when need to
change the lamp. After replace the lamp, need to reset the
timer which is built into TV.
(2) Life of the lamp unit is about 5000 hours over. Lamp use
time can be check at the lamp message MENU.
(3) If Fig.1 message appears when turn the TV on, need to
replace the lamp.
(4) Use the lamp timer reset only after replacing the lamp.
NOTE :
· This message will appear every time turn on the TV, when
the lamp needs to be replaced. Press the [OK] key to make
the message disappear, or replace the lamp.
1.3.5 HOW TO REPLACE THE LAMP UNIT
Refer to the [USERS GUIDE] for a detailed operating
description.
(1) Turn off the TV power with power key.
(2) Disconnect the power cord from the AC outlet.
(3) Loosen 1 screw from the rear side, then take out the the left
speaker panel.
(4) Loosen 1 screw then take out the lamp cover.
(5) Loosen 2 screws then take out the lamp unit.
(6) Install the new lamp unit.
(7) Re-install the lamp cover.
(8) Re-install the left speaker panel.
(9) Re-install the screw to the rear panel.
NOTE :
· After installing the new lamp unit, do not forget to reset the
lamp timer.
1.3.6 HOW TO RESET THE LAMP TIMER
Refer to the [USERS GUIDE] for a detailed operating
description.
(1) Press the [MENU] key to select CLOCK / TIMERS.
(2) Select the <LAMP TIMER RESET> with [
] / [ ] keys.
(3) Enter the <LAMP TIMER RESET> mode the message will
appears.
(4) Press the [OK] key while the above message appears on
the screen.
(5) Turn off the power, then turn on the power.
(6) The lamp timer has now been reset, as before the 1.3.2
HOW TO CONFIRMATION LAMP OPERATING TIME.
1.3.7 PRECAUTION FOR REPLACEMENT
Do not replace the LAMP UNIT immediately after the
projector has been used.
The temperature of the LAMP UNIT is still high and could
cause a burn.
Allow a cooling period of 1 hour or more before performing
replacement.
Before starting LAMP UNIT replacement work, turn off the
MAIN POWER switch, and disconnect the AC power cord
plug from the wall outlet.
If touched, the lamp glass surface may rupture and burns
may result. Do not touch the glass portion or metal portion.
Handle only plastic handle.
The replaced old lamp can be discarded in the same manner
as a fluorescent lamp. Check local ordinances and dispose
of the used lamp as prescribed.
LAMP UNIT : TS-CL110UAA
D
00
001 00 0000 0001
Operating time in decimal number notation
< D070 > Lamp operating time high byte
< D071 > Lamp operating time low byte
Operating time in hexadecimal number notation
Operating time in binary number notation
LAMP NEEDS TO BE REPLACED.
REFER TO OWNER'S MANUAL FOR
REPLACEMENT INSTRUCTIONS.
AFTER REPLACING THE LAMP,
PLEASE RESET TIMER IN THE TV
MENU.
PRESS OK, IF YOU DO NOT WAN
TO SEE THIS MESSAGE AGAIN.
Fig.1 LAMP REPLACEMENT MESSAGE