background image
SERVICE MANUAL
No. 86666
January 2002
SPECIFICATIONS (The specifications shown pertain specifically to the model GR-DV3000EG/EK)
DIGITAL VIDEO CAMERA
Printed in Japan
This service manual is printed on 100% recycled paper.
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
GR-DV3000A/EA/ED/EG/EK/SH
No.
86666
GR-DV3000A/EA/ED/EG/EK/SH
VICTOR COMPANY OF JAPAN, LIMITED
VIDEO DIVISION
S40894
Connectors
AV
Video output
: 1 V (p-p), 75
, analogue
Video input
: 0.5 V (p-p) ­ 2.0 V (p-p), 75
, analogue
Audio output
: 300 mV (rms), 1 k
, analogue, stereo
Audio input
: 300 mV (rms), 50 k
, analogue, stereo
DV
Input/output
: 4-pin, IEEE 1394 compliant
PHONE
Headphone output
: ø3.5 mm, stereo
PRINTER
: For an optional video printer equipped with a PRINT DATA
connector
AC Power Adapter/Charger AA-V40EG or AA-V40EK
Power requirement
: AC 110 V to 240 V`, 50 Hz/60 Hz
Power consumption
: 23 W
Output
Charge
: DC 7.2 V
, 1.2 A
VTR
: DC 6.3 V
, 1.8 A
Dimensions (W x H x D)
: 68 mm x 38 mm x 110 mm
Weight
AA-V40EG
: Approx. 260 g
AA-V40EK
: Approx. 340 g
Jack Box CU-V504U
General
Dimensions (W x H x D)
: 37.5 mm x 18.5 mm x 55 mm
Weight
: Approx. 30 g
Connectors
USB
: TYPE B
S-VIDEO
Output
: Y: 1 V (p-p), 75
, analogue
C: 0.29 V (p-p), 75
, analogue
Input
: Y: 0.8 V (p-p) ­ 1.2 V (p-p), 75
, analogue
C: 0.2 V (p-p) ­ 0.4 V (p-p), 75
, analogue
EDIT
: ø3.5 mm, 2-pole
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and
specifications subject to change without notice.
Camcorder
General
Power supply
: DC 6.3 V
(Using AC Power Adapter/Charger)
DC 7.2 V
(Using battery pack)
Power consumption
LCD monitor off, viewfinder on : Approx. 4.3 W
LCD monitor on, viewfinder off : Approx. 5.4 W
Dimensions (W x H x D)
: 76 mm x 90 mm x 194 mm
(with the LCD monitor closed and the viewfinder pushed back in,
without the lens hood)
Weight
: Approx. 660 g (without cassette, memory card and battery)
Approx. 740 g (incl. cassette, memory card and battery)
Operating temperature
: 0°C to 40°C
Operating humidity
: 35% to 80%
Storage temperature
: ­20°C to 50°C
Pickup
: 1/3.6" CCD
Lens
: F 1.2, f = 4.5 mm to 45 mm, 10:1 power zoom lens
Filter diameter
: ø52 mm
LCD monitor
: 3.5" diagonally measured, LCD panel/TFT active matrix system
Viewfinder
: Electronic viewfinder with 0.44" colour LCD
Speaker
: Monaural
Digital Video Camera
Format
: DV format (SD mode)
Signal format
: PAL standard
Recording/Playback format
: Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
: SP: 80 min.
(using 80 min. cassette)
LP: 120 min.
Digital Still Camera Function
Storage media
: SD Memory Card/MultiMediaCard
Compression system
: Still image
: JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
: Still image
: 4 modes (1600 x 1200 pixels, 1280 x 960 pixels,
1024 x 768 pixels, 640 x 480 pixels)
Moving image : 2 modes (240 x 176 pixels, 160 x 120 pixels)
Picture quality
: 2 modes (FINE/STANDARD)
Approximate number of storable images
(with the provided memory card [8 MB])
FINE
: 32 (640 x 480 pixels), 14 (1024 x 768 pixels),
9 (1280 x 960 pixels), 6 (1600 x 1200 pixels)
STANDARD
: 110 (640 x 480 pixels), 46 (1024 x 768 pixels),
30 (1280 x 960 pixels), 20 (1600 x 1200 pixels)
For other memory cards,
pg. 17.


background image
Important Safety Precautions
INSTRUCTIONS
1. DISASSEMBLY
1.1 BEFORE ASSEMBLY AND DISASSEMBLY ......................... 1-1
1.1.1 Precautions ..................................................................... 1-1
1.1.2 Assembly and disassembly ............................................ 1-1
1.1.3 Destination of connectors ............................................... 1-1
1.1.4 Disconnection of Connectors (Wires) ............................. 1-1
1.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY,
ASSEMBLY AND ADJUSTMENT ......................................... 1-2
1.2.1 Tools required for adjustments ........................................ 1-2
1.3 DISASSEMBLY/ASSEMBLY OF CABINET PARTS AND
BOARD ASSEMBLY ............................................................. 1-2
1.3.1 Disassembly flow chart ................................................... 1-2
1.3.2 Disassembly method ...................................................... 1-3
1.4 DISASSEMBLY OF THE 4 OP BLOCK AND
CCD BOARD ASSEMBLIES ................................................. 1-8
1.4.1 Precautions ..................................................................... 1-8
1.4.2 How to remove ................................................................ 1-8
1.4.3 How to install .................................................................. 1-8
1.4.4 Replacement of Service Repair Parts ............................ 1-8
1.5 7 E.VF(COLOR) ................................................................... 1-9
1.5.1 Disassembly/Assembly of the 7 E.VF(COLOR) ............. 1-9
1.6 DISASSEMBLY/ASSEMBLY OF THE @ MONITOR ASSEMBLY 1-10
1.6.1 @ Monitor Assembly and Hinge Assembly ................... 1-10
1.7 MANUAL EJECTION OF THE CASSETTE TAPE ............... 1-11
1.8 EMERGENCY DISPLAY ..................................................... 1-12
1.9 SERVICE NOTE .................................................................. 1-13
2. MECHANISM ADJUSTMENT
2.1 PRELIMINARY REMARKS ON ADJUSTMENT AND REPAIR .. 2-1
2.1.1 Precautions ..................................................................... 2-1
2.1.2 Notes on procedure for disassemby/assembly ............... 2-1
2.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY,
ASSEMBLY AND ADJUSTMENT ......................................... 2-2
2.2.1 Tools required for adjustments ........................................ 2-2
2.3 DISASSEMBLY/ASSEMBLY OF MECHANISM ASSEMBLY 2-3
2.3.1 General statement .......................................................... 2-3
2.3.2 Explanation of mechanism mode ................................... 2-3
2.3.3 Mechanism timing chart .................................................. 2-4
2.4 DISASSEMBLING PROCEDURE TABLE ............................. 2-5
2.4.1 Disassembly/assembly ................................................... 2-7
2.4.2 List of procedures for disassembly ............................... 2-13
2.5 CHECKUP AND ADJUSTMENT OF MECHANISM PHASE .. 2-14
2.6 MECHANISM ADJUSTMENTS .......................................... 2-15
2.6.1 Adjustment of the slide guide plate ............................... 2-15
2.6.2 Adjustment of the Tension Arm and Pad Arm Assemblies 2-16
2.6.3 Adjustment of the Slide Lever 2 .................................... 2-16
2.7 SERVICE NOTE .................................................................. 2-17
2.8 JIG CONNECTOR CABLE CONNECTION ........................ 2-19
2.8.1 Tape pattern check ....................................................... 2-20
3. ELECTRICAL ADJUSTMENT
3.1 PRECAUTION ....................................................................... 3-1
3.2 SETUP .................................................................................. 3-2
3.3 MONITOR ADJUSTMENT .................................................... 3-3
3.3.1 PLL (MONI) .................................................................... 3-3
3.4 ELECTRONIC VIEWFINDER (E.VF) ADJUSTMENT ........... 3-3
3.4.1 PLL (VF) ......................................................................... 3-3
TABLE OF CONTENTS
Section
Title
Page
Section
Title
Page
4. CHARTS AND DIAGRAMS
NOTES OF SCHEMATIC DIAGRAM .......................................... 4-1
CIRCUIT BOARD NOTES ........................................................... 4-2
4.1 BOARD INTERCONNECTIONS ........................................... 4-3
4.2 MAIN IF SCHEMATIC DIAGRAM ............................................... 4-5
4.3 SYSCON-CPU SCHEMATIC DIAGRAM .................................... 4-7
4.4 MSD-CPU SCHEMATIC DIAGRAM ............................................ 4-9
4.5 AUDIO AD/DA SCHEMATIC DIAGRAM ................................... 4-11
4.6 MAIN AUDIO SCHEMATIC DIAGRAM ..................................... 4-13
4.7 DVMAIN SCHEMATIC DIAGRAM ............................................ 4-15
4.8 VIDEO I/O SCHEMATIC DIAGRAM ......................................... 4-17
4.9 CDS/AD SCHEMATIC DIAGRAM ............................................. 4-19
4.10 DSP SCHEMATIC DIAGRAM ................................................ 4-21
4.11 OP DRIVE SCHEMATIC DIAGRAM ...................................... 4-23
4.12 TG/VDR SCHEMATIC DIAGRAM .......................................... 4-25
4.13 DSC SCHEMATIC DIAGRAM ................................................ 4-27
4.14 DSC IF AND SD SCHEMATIC DIAGRAMS ........................... 4-29
4.15 USB SCHEMATIC DIAGRAM ................................................ 4-31
4.16 MDA SCHEMATIC DIAGRAM ................................................ 4-33
4.17 PRE/REC SCHEMATIC DIAGRAM ........................................ 4-35
4.18 JUNCTION SCHEMATIC DIAGRAM ..................................... 4-37
4.19 REG SCHEMATIC DIAGRAM ................................................ 4-39
4.20 MONITOR SCHEMATIC DIAGRAM ....................................... 4-41
4.21 JACK SCHEMATIC DIAGRAM .............................................. 4-43
4.22 EJECT, DECK OPE. AND CCD SCHEMATIC DIAGRAMS .. 4-45
4.23 FE SW, FRONT, ZOOM UNIT, POWER OPE. UNIT, FOCUS UNIT
AND SW FPC UNIT SCHEMATIC DIAGRAMS ................................ 4-47
4.24 VF BL SCHEMATIC DIAGRAM .............................................. 4-49
4.25 MAIN CIRCUIT BOARD [GR-DV3000EG] ............................. 4-51
4.26 MAIN CIRCUIT BOARD [GR-DV3000EK/A/EA/ED/SH] ......... 4-57
4.27 DSC CIRCUIT BOARD ........................................................... 4-63
4.28 PRE/MDA CIRCUIT BOARD .................................................. 4-65
4.29 JUNCTION AND JACK CIRCUIT BOARDS ........................... 4-67
4.30 REG CIRCUIT BOARD [GR-DV3000EG] ............................... 4-69
4.31 REG CIRCUIT BOARD [GR-DV3000EK/A/EA/ED/SH] .......... 4-71
4.32 MONITOR CIRCUIT BOARD ................................................. 4-73
4.33 EJECT AND DECK OPE. CIRCUIT BOARDS ....................... 4-75
4.34 CCD CIRCUIT BOARD .......................................................... 4-77
4.35 FE SW AND FRONT CIRCUIT BOARDS .............................. 4-78
4.36 VF BL CIRCUIT BOARD ........................................................ 4-79
4.37 VOLTAGE CHARTS ............................................................... 4-80
4.38 POWER SYSTEM BLOCK DIAGRAM ................................... 4-85
4.39 VIDEO SYSTEM BLOCK DIAGRAM ...................................... 4-87
4.40 REGULATOR SYSTEM BLOCK DIAGRAM .......................... 4-91
5. PARTS LIST
5.1 PACKING AND ACCESSORY ASSEMBLY <M1> ............... 5-1
5.2 FINAL ASSEMBLY <M2> ..................................................... 5-3
5.3 MECHANISM ASSEMBLY <M3> ......................................... 5-6
5.4 ELECTRONIC VIEWFINDER ASSEMBLY <M4> ................ 5-8
5.5 MONITOR ASSEMBLY <M5> .............................................. 5-9
5.6 ELECTRICAL PARTS LIST ................................................. 5-10
MAIN BOARD ASSEMBLY <01> ............................................. 5-10
DSC BOARD ASSEMBLY <02> .............................................. 5-17
PRE/MDA BOARD ASSEMBLY <03> ..................................... 5-18
JUNCTION BOARD ASSEMBLY <04> ................................... 5-19
REG BOARD ASSEMBLY <05> .............................................. 5-19
MONITOR BOARD ASSEMBLY <06> ..................................... 5-20
JACK BOARD ASSEMBLY <07> ............................................. 5-22
EJECT BOARD ASSEMBLY <08> .......................................... 5-22
DECK OPE. BOARD ASSEMBLY <09> .................................. 5-22
CCD BOARD ASSEMBLY <10> .............................................. 5-23
FE SW BOARD ASSEMBLY <11> .......................................... 5-23
FRONT BOARD ASSEMBLY <12> ......................................... 5-23
VF BL BOARD ASSEMBLY <13> ............................................ 5-23
GR-DV3000EG
GR-DV3000EK
GR-DV3000EA
GR-DV3000A
GR-DV3000SH
GR-DV3000ED
AC ADAPTER CHARGER
AA-V40EG
AA-V40EK
AA-V40EA
AA-V40A
AA-V40SH
AA-V40ED
PERI-RCA ADAPTER
USED
USED
NOT USED
NOT USED
NOT USED
NOT USED
CONVERSION PLUG
NOT USED
NOT USED
NOT USED
USED
NOT USED
NOT USED
The following table lists the differing points between Models GR-DV3000EG, GR-DV3000EK, GR-DV3000EA, GR-DV3000A,
GR-DV3000SH and GR-DV3000ED in this serise.


background image
Important Safety Precautions
Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the
countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions
when a set is being serviced.
Fig.1
1. Locations requiring special caution are denoted by labels and in-
scriptions on the cabinet, chassis and certain parts of the product.
When performing service, be sure to read and comply with these
and other cautionary notices appearing in the operation and serv-
ice manuals.
2. Parts identified by the
! symbol and shaded (
) parts are
critical for safety.
Replace only with specified part numbers.
Note: Parts in this category also include those specified to com-
ply with X-ray emission standards for products using
cathode ray tubes and those specified for compliance
with various regulations regarding spurious radiation
emission.
3. Fuse replacement caution notice.
Caution for continued protection against fire hazard.
Replace only with same type and rated fuse(s) as specified.
4. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
5. Use specified insulating materials for hazardous live parts. Note
especially:
1) Insulation Tape
3) Spacers
5) Barrier
2) PVC tubing
4) Insulation sheets for transistors
6. When replacing AC primary side components (transformers, power
cords, noise blocking capacitors, etc.) wrap ends of wires securely
about the terminals before soldering.
Power cord
Fig.2
10. Also check areas surrounding repaired locations.
11. Products using cathode ray tubes (CRTs)
In regard to such products, the cathode ray tubes themselves, the
high voltage circuits, and related circuits are specified for compli-
ance with recognized codes pertaining to X-ray emission.
Consequently, when servicing these products, replace the cath-
ode ray tubes and other parts with only the specified parts. Under
no circumstances attempt to modify these circuits.
Unauthorized modification can increase the high voltage value and
cause X-ray emission from the cathode ray tube.
12. Crimp type wire connector
In such cases as when replacing the power transformer in sets
where the connections between the power cord and power trans-
former primary lead wires are performed using crimp type connec-
tors, if replacing the connectors is unavoidable, in order to prevent
safety hazards, perform carefully and precisely according to the
following steps.
1) Connector part number : E03830-001
2) Required tool : Connector crimping tool of the proper type which
will not damage insulated parts.
3) Replacement procedure
(1) Remove the old connector by cutting the wires at a point
close to the connector.
Important : Do not reuse a connector (discard it).
Fig.7
cut close to connector
Fig.3
(2) Strip about 15 mm of the insulation from the ends of the
wires. If the wires are stranded, twist the strands to avoid
frayed conductors.
15 mm
Fig.4
(3) Align the lengths of the wires to be connected. Insert the
wires fully into the connector.
Connector
Metal sleeve
Fig.5
(4) As shown in Fig.6, use the crimping tool to crimp the metal
sleeve at the center position. Be sure to crimp fully to the
complete closure of the tool.
I
·Precautions during Servicing
7. Observe that wires do not contact heat producing parts (heatsinks,
oxide metal film resistors, fusible resistors, etc.)
8. Check that replaced wires do not contact sharp edged or pointed
parts.
9. When a power cord has been replaced, check that 10-15 kg of
force in any direction will not loosen it.
1.2
5
2.0
5.5
Crimping tool
Fig.6
(5) Check the four points noted in Fig.7.
Not easily pulled free
Crimped at approx. center
of metal sleeve
Conductors extended
Wire insulation recessed
more than 4 mm
S40888-01


background image
·Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned
to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety
standards.
1. Insulation resistance test
Confirm the specified insulation resistance or greater between power cord plug prongs and exter-
nally exposed parts of the set (RF terminals, antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.). See table 1 below.
2. Dielectric strength test
Confirm specified dielectric strength or greater between power cord plug prongs and exposed acces-
sible parts of the set (RF terminals, antenna terminals, video and audio input and output terminals,
microphone jacks, earphone jacks, etc.). See table 1 below.
3. Clearance distance
When replacing primary circuit components, confirm specified clearance distance (d), (d') be-
tween soldered terminals, and between terminals and surrounding metallic parts. See table 1
below.
4. Leakage current test
Confirm specified or lower leakage current between earth ground/power cord plug prongs and
externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and
output terminals, microphone jacks, earphone jacks, etc.).
Measuring Method : (Power ON)
Insert load Z between earth ground/power cord plug prongs and externally exposed accessible
parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 and following
table 2.
5. Grounding (Class 1 model only)
Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in, Video out,
Audio in, Audio out or Fixing screw etc.).
Measuring Method:
Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.
Fig. 10
Fig. 9
Fig. 8
Table 1 Specifications for each region
Table 2 Leakage current specifications for each region
Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.
II
S40888-01
ab
c
V
A
Externally
exposed
accessible part
Z


background image
1-1
(1)
(2)
(3)
(4)
(5)
SECTION 1
DISASSEMBLY
1.1.4 Disconnection of Connectors (Wires)
Connector
Pull both ends of the connector in the arrow direction, re-
move the lock and disconnect the flat wire.
1.1 BEFORE ASSEMBLY AND DISASSEMBLY
1.1.1 Precautions
1. Be sure to remove the power supply unit prior to mount-
ing and soldering of parts.
2. When removing a component part that needs to discon-
nect the connector and to remove the screw for remov-
ing itself, first disconnect the connecting wire from the
connector and then remove the screw beforehand.
3. When connecting and disconnecting the connectors, be
careful not to damage the wire.
4. Carefully remove and handle the part to which some
spacer or shield is attached for reinforcement or insula-
tion.
5. When replacing chip parts (especially IC parts), desolder
completely first (to prevent peeling of the pattern).
6. Tighten screws properly during the procedures.
Unless specified otherwise, tighten screws at a torque
of 0.078N·m(0.8kgf·cm).
1.1.2 Assembly and disassembly
(1) Indicate the disassembly steps. When assembling, per-
form in the reverse order of these steps. This number
corresponds to the number in the disassembly diagram.
(2) Indicates the name of disassembly/assembly parts.
(3) Indicates the number in the disassembly diagram.
(4) Indicates parts and points such as screws, washers,
springs which must be removed during disassembly/
assembly.
Symbol
Name, Point
S
Screw
L
Lock, Pawl, Hook
SD
Soldering
(Others) Connector, Cover, Bracket, etc.
(Example)
· 2 (S1)
: Remove the two screws (S1) for removing
the part 1.
· CN 1a
: Disconnect the connector 1a.
·SD1
: Unsolder at the point SD1.
(5) Precautions on disassembly/assembly.
1.1.3 Destination of connectors
Note:
Three kinds of double-arrows in connection tables re-
spectively show kinds of connector/wires.
: Wire
: Flat wire
: Board to Board connector
[Example]
Note:
Remove the parts marked in
.
Fig. 1-1-1 Connector 1
Connector
Flat wire
Fig. 1-1-2 Connector 2
Connector
Flat wire
Extend the locks in the direction of the arrow for unlocking
and then pull out the wire. After removing the wire, immedi-
ately restore the locks to their original positions because
the locks are apt to come off the connector.
B-B connector
Pull the board by both the sides in the direction of the ar-
row for disconnecting the B-B connector.
Fig. 1-1-3 Connector 3
Connector
Connector
Fig. 1-1-4 Connector 4
Connector
STEP
No.
PART
Fig.No.
POINT
NOTE
CONN.
No.
Pin No.
CONNECTOR
1a
JUNCTION
CN1102
ZOOM OPE
­
8
1
ZOOM OPE UNIT Fig.1-3-1 3(S1),(L1a),5(L1b),CN1a-
2
FRONT COVER
Fig.1-3-2a CN2a,CN2b,2(S2a),(S2b),
NOTE2a
ASSY
(S2c),(S2d),2(S2e),CN2c
NOTE2b
NOTE2c
NOTE2d