background image
AV32L2EU
/
AV28L2EU
/
AV32X10EU
/
AV28X10EU
LCT0887-001A-U
0103-T-CR-JMUK
© 2001 VICTOR COMPANY OF JAPAN, LIMITED
VICTOR COMPANY OF JAPAN, LIMITED
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
CASTELLANO
ITALIANO
PORTUGUÊS
AV32X10EU
AV28X10EU
COLOUR TELEVISION
INSTRUCTIONS
FARBFERNSEHGERÄT
BEDIENUNGSANLEITUNG
TELEVISEUR COULEUR
MANUEL D'INSTRUCTIONS
KLEURENTELEVISIE
GEBRUIKSAANWIJZING
TELEVISOR A COLOR
MANUAL DE INSTRUCCIONES
TELEVISORE A COLORI
ISTRUZIONI
TELEVISOR A CORES
INSTRUÇÕES
AV28L2EU
AV32L2EU
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
CASTELLANO
ITALIANO
PORTUGUÊS
AV32/28L2EU/ LCT0887-001A-U/ English
LCT0887-001A-U_Cover.fm Page 1 Wednesday, March 7, 2001 1:08 PM


background image
ENGL
ISH
4444
AV32/28L2EU/ LCT0887-001A-U/ English
15 cm
10 cm
10 cm
15 cm
Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly be-
fore you begin.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE
USE OF THIS UNIT.
1. Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit.
2. Avoid damaging the AC plug and power cord.
3. Avoid improper installation and never position the unit where good ventilation is unattainable.
When installing this television, distance recom-
mendations must be maintained between the
floor and wall, as well as installation in a tightly
enclosed area or piece of furniture. Adhere to
the minimum distance guidelines shown for
safe operation.
4. Do not allow objects or liquid into the cabinet openings.
5. In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.
6. The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never
use any cleaner or detergent on it.
7. The main power button on the TV does not fully isolate the TV from the AC supply. If you are
not going to use this TV for a long period of time, be sure to disconnect the AC plug from the
AC socket.
CONTENTS
PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
T-V LINK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL BUTTONS AND FUNCTIONS . . . . . . . . 9
MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PICTURE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PICTURE FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SOUND SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ADDITIONAL MENU OPERATIONS . . . . . . . . . . . . . . . . . . . . 28
ADDITIONAL PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . 31
CH/CC NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TV BUTTONS AND PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
AV28L2EU_Eng.book Page 1 Wednesday, March 7, 2001 4:37 PM


background image
5
AV32/28L2EU/ LCT0887-001A-U/ English
35(3$5$7,21
35(3$5$7,21
35(3$5$7,21
35(3$5$7,21
s
s
s
s
&RQQHFWLQJ#WKH#$HULDO#DQG#9&5
&RQQHFWLQJ#WKH#$HULDO#DQG#9&5
&RQQHFWLQJ#WKH#$HULDO#DQG#9&5
&RQQHFWLQJ#WKH#$HULDO#DQG#9&5
If connecting a VCR, follow
A B C .
If not connecting a VCR, follow
1.
To operate T-V LINK functions, a T-V LINK compatible VCR
must be connected to the EXT-2 terminal on the TV. For de-
tails about T-V LINK functions, see "T-V LINK FUNCTIONS"
on page 5.
Note:
· For further details, refer to the manuals provided with the
devices to be connected.
· The connecting cables are not provided.
· A video can be viewed from the VCR without performing
C. For details, refer to your VCR instruction manual.
· To connect additional external devices, please see "AD-
DITIONAL PREPARATION" on page 31.
· To connect speakers and amplifier, please see "Con-
necting Speakers/Amplifier" on page 32.
· When a decoder is connected to a T-V LINK compatible
VCR, set the DECODER (EXT-2) function to ON. For de-
tails, see "Using the DECODER (EXT-2) function" on
page 29. Otherwise, you will not be able to view scram-
bled channels.
s
s
s
s
&RQQHFWLQJ#WKH#SRZHU#FRUG#WR#WKH#$&#RXWOHW
&RQQHFWLQJ#WKH#SRZHU#FRUG#WR#WKH#$&#RXWOHW
&RQQHFWLQJ#WKH#SRZHU#FRUG#WR#WKH#$&#RXWOHW
&RQQHFWLQJ#WKH#SRZHU#FRUG#WR#WKH#$&#RXWOHW
Caution:
· Operate only from the power source specified
(AC 220 ­ 240 V, 50 Hz) on the unit.
s
s
s
s
3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO
3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO
3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO
3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO
Use two AAA/R03 dry cell batteries.
Insert the batteries from the
ó end, making sure the ô and ó
polarities are correct.
To open the battery compartment, slide the door downwards and
lift off. Replace the door by sliding it upwards until it is secure.
Note:
· Follow the warnings printed on the batteries.
· Battery life is about six months to one year, depending on
your frequency of use.
· If the remote control does not work properly, replace the
batteries.
· The batteries we supply are only for setting up and test-
ing your TV, please replace them as soon as necessary.
· Always use good quality batteries.
EXT-
1
EXT-
2
S
EXT-
3
S
R
AUDIO OUT
L
75-ohm
Coaxial
Cable
21-pin SCART
Cable
Back of the TV
75-ohm
Coaxial
Cable
Aerial
AV IN/OUT
Terminal
To Aerial
Output
To Aerial
Input
VCR
AV28L2EU_Eng.book Page 2 Wednesday, March 7, 2001 4:37 PM


background image
6
PREPARATION
ENGL
ISH
AV32/28L2EU/ LCT0887-001A-U/ English
s
s
s
s
,QLWLDO#6HWWLQJV
,QLWLDO#6HWWLQJV
,QLWLDO#6HWWLQJV
,QLWLDO#6HWWLQJV
When the TV is first turned on, it enters the initial setting
mode, and the JVC logo is displayed. Follow the instructions
on the on-screen display to make the initial settings.
1 Press the Main power button on the TV.
The Power lamp lights red (for power on), then green (for
TV on) and the JVC logo is displayed.
Note:
· If the power lamp stays red and does not change to
green:
Your TV is in the standby mode. Press the
ü
(Standby) button on the remote control to turn your
TV on.
· The JVC logo does not appear when your TV has
been turned on once.
In this case, use the "LANGUAGE" and "AUTO PRO-
GRAM" functions to make the initial settings. For de-
tails, see "INSTALL" on page 23.
2 Press the
á button.
The LANGUAGE menu appears.
3 Press the
ì and ë buttons to
choose ENGLISH. Then press the
á button.
English is set for the on-screen display description. The
COUNTRY menu appears as a sub-menu of the AUTO
PROGRAM function.
There are two COUNTRY menus. Pressing the yellow
button changes the COUNTRY menu as follows:
4 Press the
ì and ë buttons to
choose the country where you are
now located.
D0001-EN
D0002(E)-EN
BACK
LANGUAGE
TV
OK
BACK
MORE
START
TV
OK
BACK
MORE
START
TV
OK
D0003-EN
1
2
3
4
5
6
7
8
9
0
P
AV
TV
OK
MENU
P
TV
< AV32L2EU/AV28L2EU >
< AV32X10EU/AV28X10EU >
Main power
button
Power lamp
Blue button
Yellow button
Main power
button
Power lamp
AV28L2EU_Eng.book Page 3 Wednesday, March 7, 2001 4:37 PM


background image
PREPARATION
7
AV32/28L2EU/ LCT0887-001A-U/ English
5 Press the blue button to start the
AUTO PROGRAM function.
The AUTO PROGRAM menu appears and received TV
channels are automatically registered in the Programme
numbers (PR).
If "ACI START/ACI SKIP" appears in the AUTO PRO-
GRAM menu:
You can use the ACI (Automatic Channel Installation)
function to decode the ACI data and complete the regis-
tration of all the TV channels in a short period of time.
For details of the ACI function and how to use it, refer to
"Using the ACI function" on page 28.
If you don't want to use the ACI function, press the
ë
button to choose ACI SKIP and then press
ýýýýá .
To cancel the AUTO PROGRAM function:
Press the
button.
6 After the TV channels have been
registered in the Programme num-
bers (PR), the EDIT menu appears.
You can proceed to edit the Programme numbers (PR)
using the EDIT/MANUAL function. For details, see "ED-
IT/MANUAL" on page 24.
When not using the EDIT/MANUAL function:
If you do not need to use the EDIT/MANUAL function, go
to the next step.
7 Press the
á button to display the
T-V LINK menu.
8 Operate the T-V LINK menu accord-
ing to the type of a VCR connected
to the EXT-2 terminal.
When a T-V LINK compatible VCR is not con-
nected:
Press the
button to exit the T-V LINK menu.
The T-V LINK menu disappears.
When a T-V LINK compatible VCR is connected:
Follow the operating procedure "Downloading the data
to VCR" on page 28 to transmit the Programme number
(PR) data.
9 Now, the initial settings are com-
plete, and you can watch the TV.
Note:
· When your TV can detect the TV channel name from
the TV channel broadcast signal, it automatically
registers the TV channel name (ID) to the Pro-
gramme number (PR) in which the TV channel has
been registered.
· If a TV channel you want to view is not set to a Pro-
gramme number (PR), manually set it using the
MANUAL function. For details, see "EDIT/MANUAL"
on page 24.
· The TV channel is not registered in Programme
number PR 0 (AV). When you want to register a TV
channel to PR 0 (AV), manually set it using the MAN-
UAL function. For details, see "EDIT/MANUAL" on
page 24.
BACK
TV
OK
EDIT
CH / CC
PR
ID
AV
01
02
03
04
05
06
07
08
09
CH
CH
BBC1
CH
CH
CH
CH
CC
CC
CC
21
23
22
26
25
24
01
02
03
ID
INSERT
DELETE
MANUAL
CH 10
AUTO PROGRAM
20%
D0004-EN
MOVE
BACK
TV
OK
D0005-EN
BACK
DOWNLOAD
TV
VCR
T-V LINK
TV
OK
EXIT
AV28L2EU_Eng.book Page 4 Wednesday, March 7, 2001 4:37 PM