background image
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
CASTELLANO
ITALIANO
PORTUGUÊS
AV28CT1EP / LCT1136-001A-U
VICTOR COMPANY OF JAPAN, LIMITED
$9&7(3
AV28CT1EP
COLOUR TELEVISION
INSTRUCTIONS
FARBFERNSEHGERÄT
BEDIENUNGSANLEITUNG
TELEVISEUR COULEUR
MANUEL D'INSTRUCTIONS
KLEURENTELEVISIE
GEBRUIKSAANWIJZING
TELEVISOR A COLOR
MANUAL DE INSTRUCCIONES
TELEVISORE A COLORI
ISTRUZIONI
TELEVISOR A CORES
INSTRUÇÕES
LCT1136-001A-U
0112-T-CR-JMUK
©2001 VICTOR COMPANY OF JAPAN, LIMITED
LCT1136-001A-U_All Cover.fm Page 1 Tuesday, December 18, 2001 1:25 PM


background image
ENG
L
ISH
1
11
1
AV28CT1EP / LCT1136-001A-U / English
15 cm
10 cm
10 cm
15 cm
Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly be-
fore you begin.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE
USE OF THIS UNIT.
1. Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit.
2. Avoid damaging the AC plug and power cord.
3. Avoid improper installation and never position the unit where good ventilation is unattainable.
When installing this television, distance recom-
mendations must be maintained between the
floor and wall, as well as instalment in a tightly
enclosed area or piece of furniture. Adhere to
the minimum distance guidelines shown for
safe operation.
4. Do not allow objects or liquid into the cabinet openings.
5. In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.
6. The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never
use any cleaner or detergent on it.
When you do not use this TV set for a long period of time, be sure to disconnect the power plug
from the AC socket.
CONTENTS
PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
T-V LINK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL BUTTONS AND FUNCTIONS . . . . . . . . 9
MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PICTURE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PICTURE FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SOUND SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ADDITIONAL MENU OPERATIONS . . . . . . . . . . . . . . . . . . . . 28
ADDITIONAL PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . 30
CH/CC NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
TV BUTTONS AND PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
AV28CT1EP_EN.book Page 1 Tuesday, December 18, 2001 1:20 PM


background image
2
AV28CT1EP / LCT1136-001A-U / English
PREPARATION
PREPARATION
PREPARATION
PREPARATION
I
I
I
I Connecting the Aerial and VCR
Connecting the Aerial and VCR
Connecting the Aerial and VCR
Connecting the Aerial and VCR
If connecting a VCR, follow A
B C D.
If not connecting a VCR, follow 1
2.
*1: To operate T-V LINK functions, a T-V LINK compatible
VCR must be connected to the EXT-2 terminal on the TV.
For details about T-V LINK functions, see "T-V LINK
FUNCTIONS" on page 5.
Note:
· For further details, refer to the manuals provided with the
devices to be connected.
· The connecting cables are not provided.
· A video can be viewed from the VCR without performing
C. For details, refer to your VCR instruction manual.
· To connect additional external devices, please see "AD-
DITIONAL PREPARATION" on page 30.
· When a decoder is connected to a T-V LINK compatible
VCR, set the DECODER (EXT-2) function to ON. For de-
tails, see "Using the DECODER (EXT-2) function" on
page 28. Otherwise, you will not be able to view scram-
bled channels.
I
I
I
I Putting Batteries into the Remote Control
Putting Batteries into the Remote Control
Putting Batteries into the Remote Control
Putting Batteries into the Remote Control
Use two AAA/R03 dry cell batteries.
Insert the batteries from the - end, making sure the + and -
polarities are correct.
To open the battery compartment, slide the door downwards
and lift off. Replace the door by sliding it upwards until it is se-
cure.
Note:
· Follow the warnings printed on the batteries.
· Battery life is about six months to one year, depending on
your frequency of use.
· If the remote control does not work properly, replace the
batteries.
· The batteries we supply are only for setting up and test-
ing your TV, please replace them as soon as necessary.
· Always use good quality batteries.
EXT-
1
EXT-
2
EXT-
3
VCR
*1
EXT-
2
S
EXT-
1
EXT-
3
S
VHF/UHF
Aerial
75-ohm Coaxial
Cable
AC Outlet
(AC 220 - 240 V,
50 Hz)
21-pin SCART Cable
75-ohm
Coaxial
Cable
AV IN/OUT
Terminal
To Aerial
Output
To Aerial
Input
AV28CT1EP_EN.book Page 2 Tuesday, December 18, 2001 1:20 PM


background image
3
PREPARATION
ENG
L
ISH
AV28CT1EP / LCT1136-001A-U / English
I
I
I
I Initial Settings
Initial Settings
Initial Settings
Initial Settings
When the TV is first turned on, it enters the initial setting
mode, and the JVC logo is displayed. Follow the instructions
on the on-screen display to make the initial settings.
1 Press the Main power button on the TV.
The Power lamp lights red (for power on), then green (for
TV on) and the JVC logo is displayed.
Note:
· If the power lamp stays red and does not change to
green:
Your TV is in the standby mode. Press the
#
(Standby) button on the remote control to turn your
TV on.
· The JVC logo does not appear when your TV has
been turned on once.
In this case, use the "LANGUAGE" and "AUTO PRO-
GRAM" functions to make the initial settings. For de-
tails, see "INSTALL" on page 23.
2 Press the a
a
a
a button.
The LANGUAGE menu appears.
3 Press the 6
6
6
6 buttons to choose
ENGLISH. Then press the
a
a
a
a but-
ton.
English is set for the on-screen display description. The
COUNTRY menu appears as a sub-menu of the AUTO
PROGRAM function.
4 Press the 5
5
5
5 and 6
6
6
6 buttons to
choose the country where you are
now located.
1
2
3
4
5
6
7
8
9
0
P
AV
TV
OK
MENU
P
FREEZE
SUB-P
F.T/L
TV
Main power button
Power lamp
Blue button
AV28CT1EP_EN.book Page 3 Tuesday, December 18, 2001 1:20 PM


background image
PREPARATION
4
AV28CT1EP / LCT1136-001A-U / English
5 Press the blue button to start the
AUTO PROGRAM function.
The AUTO PROGRAM menu appears and received TV
channels are automatically registered in the Programme
numbers (PR).
To cancel the AUTO PROGRAM function:
Press the
b button.
6 After the TV channels have been
registered in the Programme num-
bers (PR), the EDIT menu appears.
You can proceed to edit the Programme numbers (PR)
using the EDIT/MANUAL function. For details, see "ED-
IT/MANUAL" on page 24.
When not using the EDIT/MANUAL function:
If you do not need to use the EDIT/MANUAL function, go
to the next step.
7 Press the a
a
a
a button to display the
T-V LINK menu.
8 Operate the T-V LINK menu accord-
ing to the type of a VCR connected
to the EXT-2 terminal.
When a T-V LINK compatible VCR is not con-
nected:
Press the b button to exit the T-V LINK menu.
The T-V LINK menu disappears.
When a T-V LINK compatible VCR is connected:
Follow the operating procedure "Downloading the data
to VCR" on page 28 to transmit the Programme number
(PR) data.
9 Now, the initial settings are com-
plete, and you can watch the TV.
Note:
· When your TV can detect the TV channel name from
the TV channel broadcast signal, it automatically
registers the TV channel name (ID) to the Pro-
gramme number (PR) in which the TV channel has
been registered.
· If a TV channel you want to view is not set to a Pro-
gramme number (PR), manually set it using the
MANUAL function. For details, see "EDIT/MANUAL"
on page 24.
· The TV channel is not registered in Programme
number PR 0 (AV). When you want to register a TV
channel to PR 0 (AV), manually set it using the MAN-
UAL function. For details, see "EDIT/MANUAL" on
page 24.
AV28CT1EP_EN.book Page 4 Tuesday, December 18, 2001 1:20 PM