background image
Owner's Manual
GT65/212
Three-channel Guitar Amplifiers


background image
TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Suggested Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . .7
Technical Specifications . . . . . . . . . . . . . . . . .back cover
GT65/212 Guitar Amplifier
IMPORTANT SAFETY INSTRUCTIONS
· READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
· DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNIT REQUIRES 3" (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR
FLOW PROVISIONS IN THE CABINET.
· DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
· CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
· ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
· PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
· UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
· ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR
SAFE OPERATION AND TO AVOID INJURY.
· WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE..
· SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
· OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PRO-
TECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS-
TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
"ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES."
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
"VOLTAJE PELIGROSO"
"DANGER HAUTE TENSION"
=
=
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.


background image
3
GT65/212 Guitar Amplifier
Congratulations!
You are now the proud owner of the Crate GT65/212
three-channel guitar amplifier. This rugged amplifier combines
outstanding features with serious clean and distorted sounds.
Front panel RCA input jacks allow you to play along with your
favorite CD or tape. The rear panel Insert Jack allows you to
connect your effects for greater flexibility. Channel switching
and reverb may be controlled by means of a footswitch.
Like all Crate products, your GT amplifier is designed by
musicians, and built using only the best components.
Extensive testing confirms that this amplifier is the absolute
best it can be.
In order to get the most out of your new amplifier, we
strongly urge you to read the information contained in this
manual before you begin playing.
And thank you for choosing Crate.
Declaration Of Conformity
#30, Effective 01-01-2001
Manufacturer's Name:
SLM Electronics
Production Facility:
11880 Borman Drive, St. Louis, MO 63146, USA
Production Facility:
700 Hwy 202 W, Yellville, AR 72687, USA
Shipping Facility:
1400 Ferguson Ave., St. Louis, MO 63133, USA
Office Facility:
1400 Ferguson Ave., St. Louis, MO 63133, USA
Product Type:
Audio Amplifier
Complies with Standards:
LVD:
92/31/EEC, 93/68/EEC, & 73/23/EWG
Safety:
EN60065
EMC:
EN55013, EN55020, EN55022, EN61000-3-2,
& EN61000-3-3
Supplementary information provided by:
SLM Electronics - R & D Engineering
1901 Congressional Drive, St Louis, MO 63146, USA
Tel.: 314-569-0141, Fax: 314-569-0175


background image
The Front Panel:
4
1
3
4
5
8
9
10
11
12
6
7
2
1: INPUT: Use this jack to connect your guitar to the amplifier by means of a shielded instrument cable.
SOLO/RHYTHM CHANNELS: High gain channels giving you sounds with serious overdrive.
2: SOLO LED: This LED illuminates when the Solo channel is selected.
3: GAIN: Use this control to adjust the amount of distortion produced by the Solo channel.
4: SHAPE: Use this control to "dial in" the tone for the Solo channel. Rotating the control counterclockwise
enhances the mid frequencies, while rotating the control clockwise enhances the low and high frequencies.
5: LEVEL: Use this control to adjust the output level of the Solo channel.
6: SOLO/RHYTHM SELECT: Use this switch to select the Solo or Rhythm channel. When this switch is
depressed, the Solo channel is selected. With the switch in the out position, the Rhythm channel is select-
ed. This switch is active only when the Solo-Rhythm/Clean Select switch (#13) is depressed.
7: RHYTHM LED: This LED illuminates when the Rhythm channel is selected.
8: GAIN: Use this control to adjust the amount of distortion produced by the Rhythm channel.
9: LOW: Use this control to adjust the low frequency level of the Solo/Rhythm channel.
10: MID: Use this control to adjust the midrange frequency level of the Solo/Rhythm channel.
11: HIGH: Use this control to adjust the high frequency level of the Solo/Rhythm channel.
12: LEVEL: Use this control to adjust the output level of the Rhythm channel.
13: SOLO-RHYTHM/CLEAN SELECT: Use this switch to select the Clean channel or the Solo and
Rhythm channels. With the switch in the out position, the Clean channel is selected. When the switch is
depressed, either the Solo or Rhythm channel is selected, depending on the setting of the Solo/ Rhythm
Select switch (#6).
CLEAN CHANNEL: A normal gain channel designed to give you crystal clean sounds.
14: CLEAN LED: This LED illuminates when the Clean channel is selected.
15: VOL: Use this control to adjust the output level of the Clean channel.
16: LOW: Use this control to adjust the low frequency level of the Clean channel.
17: MID: Use this control to adjust the midrange frequency level of the Clean channel.
18: HIGH: Use this control to adjust the high frequency level of the Clean channel.
19: REVERB: Use this control to adjust the amount of reverb effect: in its fully counterclockwise position
the signal will be "dry" (without any effect). As you rotate the control clockwise the amount of reverb increas-
es.
20: CD INPUT: Use these RCA jacks to connect the output from a CD player or tape deck to the amplifier.
The signal at these jacks is combined into a mono signal which is sent to the internal power amp circuit.
Use the CD or tape player's output level control to adjust the signal for the proper mix with your guitar.
GT65/212 Guitar Amplifier


background image
15
16
17
18
19
20
21
13 14
21: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the
switch depressed). The switch illuminates when the power is on.
GT65/212 Guitar Amplifier
100VAC: T2.5A
250V
120VAC: T2A
250V
230/240VAC: T1.25A
250V
CAUTION: TO REDUCE THE RISK OF FIRE,
REPLAC E FUSE WITH SAME TYPE AND RATING.
ATTENTION: UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE.
CLEAN/
SOLO/
RHYTHM
REVERB
FOOTSWITCH
EXTENSION
SPEAKER
INSERT
22
23
24
25
26
The Rear Panel:
22: FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or
other problems. If the fuse opens, replace it ONLY with the same size and type. If fuses continue to
fail, check the AC source ­ if the source is okay, contact your Crate dealer for service information.
23: EXTENSION SPEAKER: Use this jack to connect the amplifier to an external speaker cabinet.
This jack is wired in series with the internal speaker(s) which remain active when an extension
speaker is connected.
24: REVERB FOOTSWITCH: Use this jack to connect the 1/4" mono plug on the footswitch cable to
the three-button footswitch (supplied). This allows you to remotely turn the reverb on and off.
25: CLEAN/SOLO/RHYTHM FOOTSWITCH: Use this jack to connect the 1/4" stereo plug on the
footswitch cable to the three-button footswitch (supplied). This allows you to remotely switch between
the Clean and Distortion channels and between the Solo and Rhythm channels.
26: INSERT: Use this jack to connect an external
effects device to the amplifier. Use Crate's
STP201, STP202, or STP203 stereo-to-mono Y-
cord or an adapter such as Crate's YPP117 and
two 1/4" mono signal cables to connect to the
effect as shown to the immediate right.
27: AC LINE CORD (not shown): This grounded
power cord is to be plugged into a grounded power
outlet, wired to current electrical codes and compati-
ble with the voltage, power, and frequency require-
ments stated on the rear panel. Do not attempt to
defeat the safety ground connection.
TIP
RING
SLEEVE
RETURN
SEND
GROUND
Stereo-to-mono Y-cord:
to Insert
jack
to Insert
jack
(STP201, 3'
STP202, 6'
STP203, 9')
(YPP117)
(1/4"-TO-1/4"
MONO CABLES)
to
effect
"OUT"
jack
to
effect
"IN"
jack
TIP
RING
SLEEVE
Y-adapter and 2 cables:
RING
RING
TIP
TIP
to
effect
"OUT"
jack
to
effect
"IN"
jack
External Effect
External Effect
5