background image


background image
Designedfortheperformingartist,
Crate's CA125D Acoustic Amplifier
gives you more of what you want.
More power. More clarity. More control. And,
more freedom. Imagine: microphone quality
sound, without feedback. And without being
"chained" to a mic stand!
More power:
twin 50-watt RMS power
amplifiers drive a pair of specially designed
high fidelity 8" low frequency transducers for
plenty of volume and low end punch.
More clarity:
a separate 25-watt RMS
power amp drives a highly efficient Piezo
tweeter for clean crisp highs and natural
midrange blend. A tweeter level control on
the rear panel allows you to adjust the high
frequency output to suit your taste.
More control:
three independent channels,
each with its own gain and reverb/effects
controls. The main Instrument channel fea-
tures an "Active/Piezo" switch to properly
match the pickups of your instrument, plus a
three-band rotary EQ with variable contour ­
for total control of the critical midrange fre-
quencies. An easy-to-use feedback elimination
circuit with frequency select and cut controls
lets you kill feedback without sacrificing
sound quality. Plus a footswitchable chorus
with depth and rate controls.
The Vocal/Aux channel offers both low
and high impedance inputs for both kinds of
microphones, with phantom power on the
Low-Z input. The third "Aux" channel allows
the use of a rhythm machine, background
tape, or another mic or instrument.
Still more:
The master section features
reverb and effects return controls, a five-band
graphic EQ, and the master level control. A
footswitch jack on the rear panel provides
control for reverb and chorus. Level-control-
lable XLR and 1/4" balanced line outs allow
you to patch into house sound boards or
recording consoles, plus an effects loop line-
in/line-out setup allows connection of exter-
nal effects.
Enough already?
Not for us. The CA125D
features Crate's Digital Signal Processing (DSP)
for a variety of digital reverbs, effects and
delays specifically designed for acoustic
instruments.
The CA125D was designed, evaluated,
tweaked and redesigned by musicians and
music loving engineers. Highly sophisticated
computer driven assembly machines and
highly skilled assemblers use only the finest
components to produce each amp. Every cabi-
net is hand-built and hand-covered by trained
craftsmen. The final assembled product is
tested ­ and played ­ by skilled musician/
technicians. It is only after the amplifier has
passed this barrage of picky people that it
gets packed up and shipped out.
The CA125D Acoustic Amplifier. Designed
to be its best, so you can sound your best!
About the Crate Acoustic
CA125D:


background image
Crate Acoustic amplifiers are
Made With Pride in the U.S.A.
To get this amplifier to sound its best,
read this owner's guide prior to its use.
To keep this amplifier looking its best,
avoid abrasive cleansers. Wipe the cab-
inet clean using a slightly dampened
cloth. Never use brass cleaners on the
hardware since they could damage
their protective coatings.
Crate continually develops new products, as well as improves
existing ones. For this reason, the specifications and information
in this manual are subject to change without notice.
THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED TO PROVIDE SAFE AND
RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE UNIT AND PREVENT
ACCIDENTAL DAMAGES OR INJURY, PLEASE FOLLOW THESE PRECAUTIONARY
GUIDELINES:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN CHASSIS; DO
NOT DEFEAT OR REMOVE THE GROUND PIN OF THE POWER CORD; CONNECT ONLY
TO A PROPERLY GROUNDED AC POWER OUTLET.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION: OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE
LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE
PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR
PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
"ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES."
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
"UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN"
EXPLANATION OF
GRAPHICAL SYMBOLS:
"DANGEROUS VOLTAGE"
"VOLTAJE PELIGROSO"
"DANGER HAUTE TENSION"
"GEFAHLICHE SPANNUNG"
=
=
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
VORSICHT
ELEKTRISCHE SCHLAGGEFAHR
NICHT OFFENEN
ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS
ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE
PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN
TECHNICIEN QUALIFIE.
VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT
DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM
BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM
WARTUNGSPERSONAL ZU UBERLASSEN.
Output Power Rating:
125 watts RMS total system power
Woofer Amp:
2 x 50 watts RMS @1% THD
Tweeter Amp:
25 watts RMS @1% THD
Inst. Channel: Low:
+/-15dB @ 80Hz
Mid:
+/-15dB @ 400­1.2kHz (Contour)
High:
+/-15dB @ 10kHz
Input Impedance:
25k ohm (Active), 2.2M ohm (Piezo)
Input Sensitivity:
22mV RMS (Active), 9mV RMS (Piezo)
Sens. to Eff Send/Line out:
70mV
Max Input Signal:
6v RMS (17v peak to peak)
Feedback Elimination:
Freq: variable from 80Hz to 4kHz
Cut: variable from -0 to -30dB
Voc. Ch: Input Impedance:
3k ohm (Lo-Z), 20k ohm (Hi-Z)
Input Sensitivity:
3mV RMS (Lo-Z), 15mV RMS (Hi-Z)
Sens. to Eff Send/Line out:
9mV (Lo-Z), 50mV (Hi-Z)
Max Input Signal:
10v RMS (28v peak to peak)
Aux. Ch: Input Impedance:
20k ohm
Input Sensitivity:
15mV RMS
Sens. to Eff Send/Line out:
50mV
Max Input Signal:
10v RMS (28v peak to peak)
Master EQ's:
+/-12dB @ 80Hz, 330Hz, 1kHz
4kHz, 10kHz
Effects Loop:
Line Out 1v RMS,
Line In 1v RMS
Eff Return to Line Out Sens:
50mV
Eff Return In. Impedance:
11k ohm
Eff Send Out. Impedance:
2.2k ohm
Line Out Out. Impedance:
220 ohm (Lo-Z), 2.2k ohm (Hi-Z)
Internal Woofers:
2 x 8" w/polypropylene cones,
rubber surrounds, 30oz magnet,
1" voice coil, 8 ohms, 50w RMS,
95dB 1w 1m
Internal Tweeter:
High efficiency Piezo,
110dB 1w 1m
Internal Crossover:
Active electronic type
Power Requirements:
120VAC, 60Hz, 160VA;
100/115VAC, 50/60Hz, 160VA;
230VAC, 50/60Hz, 160VA
Size and Weight:
16-3/4"H x 21"W x 10-1/2"D, 42 lbs.
Technical
Specifications:
For further information on
the CA125D, please open


background image
On the
Front Panel:
0
10
0
10
0
10
0
10
0
10
0
10
0
10
0
10
0
10
500Hz
1.2kHz
0
­15
+15
0
­15
+15
0
­15
+15
0
10
Depth
Chorus
Instrument
Rate
Gain
Input
Low
Mid
Contour
High
Freq
Cut
Rev/Eff
Send
0
­30dB
­15dB
Hi Z
Low Z
Gain
Vocal / Mic
Rev/Eff
Send
Off
On
Active
Peak
Piezo
100Hz
330Hz
1kHz
4kHz
10kHz
+12dB
­12dB
0
+12dB
­12dB
0
Graphic Eq
Power
Master
0
10
Level
500Hz
175
1.2k
80Hz
4kHz
Gain
Hi Z
Aux
Rev/Eff
Send
SPR
LAR
SAR
DLY
Multi
Mode
Rev Ret
Effects
Eff Ret
Crate Acoustic CA125D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
17
19
20
21
23
24
25
26
27
22
The Instrument channel:
1:
Input.
The signal output from your acoustic instrument may be connected here
by means of a shielded instrument cable.
2:
Active/Piezo switch.
Use this switch to select the type of pickup on your instru-
ment. For active electronic pickups, set the switch to "active" (switch out). For
passive/magnetic pickups, set it to "piezo" (switch depressed).
3:
Gain.
This serves as the input level control for the instrument channel of the
amplifier. For the best signal to noise ratio set this control so the Peak LED (#4)
flashes when playing your instrument fairly hard.
4:
Peak LED.
This LED flashes when the signal level into the preamp approaches
clipping. Adjust the Gain control (#3) until a strong signal from your instrument
causes this LED to flash.
5:
Low.
This serves as the instrument channel's primary bass control. Adjust this
control to get the best sounding bass response for your instrument. Excessive
boost of the low control can cause an unnatural howling and should be avoided.
6:
Mid.
This serves as the instrument channel's primary midrange control. Adjust
this control to get the best projection and midrange tones for your instrument.
The center point of the mid control is chosen by the setting of the contour control
(#7).
7:
Contour.
Use this control to set the center point of the mid control (#6). Set this
control at the frequency which gives you the most natural-sounding midrange
tones.
8:
High.
This serves as the instrument channel's primary treble control. Adjust this
control so your high notes and harmonic overtones are lively but not overpow-
ering.
9:
Freq.
Use this control along with the Cut control (#10) to eliminate instrument
feedback. For information on the proper use of this control, please read the sec-
tion entitled "To Eliminate Instrument Feedback."
10: Cut.
Use this control along with the Freq control (#9) to eliminate instrument
feedback. For information on the proper use of this control, please read the sec-
tion entitled "To Eliminate Instrument Feedback."
11: Rev/Eff send.
Use this control to adjust the amount of internal reverb and/or
external effect (if used) for the instrument channel.
12: Chorus On/Off switch.
This switch, when depressed, applies the internal cho-
rus effect to the instrument channel.
13: Chorus Depth.
Use this control to adjust the magnitude of the chorus effect.
Rotating this control clockwise increases the intensity of the effect.
14: Chorus Rate.
Use this control to adjust the rate of the chorus effect. Rotating this
control clockwise increases the rate at which the effect occurs.
The Vocal/Aux channel:
15: Low-Z input.
The signal output from a low impedance microphone may be con-
nected here by means of a shielded, balanced microphone cable terminated with
an XLR connector. The Low-Z jack has 15 volts phantom power applied to pins
2 and 3. (Mics not requiring phantom power will not be affected.)
16: Hi-Z input.
The signal output from a high impedance microphone or a line level
signal may be connected here by means of a shielded signal cable terminated
with a 1/4" tip/sleeve connector.
17: Gain.
This serves as the input level control for the vocal/aux channel of the
amplifier. Adjust this control for the best mix with the signals from the other
channels.
18: Rev/eff send.
Use this control to adjust the amount of internal reverb and/or
external effect (if used) for the vocal/aux channel.
The Aux channel:
19: Hi-Z input.
The signal output from a high impedance microphone or a line level
signal may be connected here by means of a shielded signal cable terminated
with a 1/4" tip/sleeve connector.
20: Gain.
This serves as the input level control for the aux channel of the amplifier.
Adjust this control for the best mix with the signals from the other channels.
21: Rev/eff send.
Use this control to adjust the amount of internal reverb and/or
external effect (if used) for the aux channel..
The Effects Section:
22: DSP Mode.
Use this control to select the type of digital signal processing applied
to the output signal. For a listing of the effects, please see the section entitled "The
DSP Section."
23: Rev Ret.
Use this control to adjust the amount of the internal reverb ­ the further
you turn to the right the deeper the effect.
24: Eff Ret.
Use this control to adjust the amount of effect applied from an external
signal processor (if used).
The Master Section:
25: Graphic EQ.
Use these sliders to control the output frequencies indicated below
each control. The center position of each control is flat (no boost or cut). Use the
graphic EQ to adjust the output of the CA125 to best suit your tastes and to com-
pensate for room acoustics.
26: Level.
Use this control to set the overall output level of the amplifier.
27: Power Switch.
Use this switch to apply power to the amplifier: the amp is on
when the top of the switch is depressed, off when the bottom of the switch is
depressed. This switch will illuminate when the amplifier is on.
To Eliminate Instrument Feedback:
One of the most common problems encountered when amplifying acoustic
instruments, especially in small environments, is feedback. Acoustic instruments typ-
ically have inherent qualities which cause resonant feedback at specific frequencies.
Instrument tone controls and sound board equalizers are helpful in getting rid of the
problem, but they typically operate around relatively wide frequency bands. This
almost always means the musician must sacrifice sound quality in his quest to do
away with feedback. But since Crate's feedback elimination circuit isolates only the
offending frequency, instrument feedback from the CA125D can be eliminated with-
out affecting the overall sound.
Chances are, you may not have a problem with feedback at all. In that case, leave
the CA125D's Freq and Cut controls fully counter-clockwise. However, if you do
encounter feedback while playing, set the Cut control to -30dB (fully clockwise) and
adjust the Freq control until the feedback is gone. Reduce the Cut to the 12 o'clock posi-
tion and readjust the Freq control as needed. Continue reducing the Cut control and
readjusting the Freq control until there is no more feedback with the Cut control as far
counter-clockwise as possible. This approach effectively eliminates instrument feed-
back without sacrificing the quality of your sound.


background image
On the
Rear Panel:
Return
Send
Low Z
Bal.
Gnd
Lift
High Z
Bal.
Reverb/
Chorus
Line Outputs
Tweeter
Effects
Loop
Foot
Switch
Level
0
10
Level
-50dB
0dB
-6dB
35
34
32
31
30
29
28
33
28: Footswitch.
Connect the supplied two-button footswitch here for remote on/off
control of the internal reverb and chorus. (When connected, the footswitch over-
rides the front panel chorus on/off switch.)
Note:
This is a STEREO jack: tip controls the chorus, ring controls the reverb, sleeve
is ground. Use only a footswitch equipped with a stereo 1/4" plug.
29: Effects Loop Send.
When using an external signal processor, connect this jack to the
input of the effect by means of a shielded signal cable.
30: Effects Loop Return.
When using an external signal processor, connect this jack to
the output of the effect by means of a shielded signal cable.
31: High Z Bal.
Use this jack to connect a high impedance, line level signal to a house
sound board, a recording console or an external power amplifier by means of an
1/4" stereo plug-terminated cable. (Ring is signal +, tip is signal -, and sleeve is
ground.)
32: Low Z Bal.
Use this jack to connect a low impedance, line level signal to a house
sound board, a recording console or an external power amplifier by means of an
XLR-terminated cable. (Pin 1 is ground, pin 2 is signal +, and pin 3 is signal -.)
33: Ground Lift.
This switch, when depressed, electronically disconnects the low Z bal-
anced output jack's chassis ground connection. If you experience excessive noise
when using the low Z balanced output jack, depress this switch.
34: Line Out Level.
Use this control to adjust the output level of the line out signal. (This
control works independently from the amplifier's master level control.)
35: Tweeter Level.
Use this control to adust the signal output level from the CA125D's
internal tweeter. Rotating this control counter-clockwise reduces the tweeter's
output level.
Not Shown:
Power cord.
Connect the end of this cord to a suitable source of line voltage. Refer
to the voltage information on the back of the amplifier for its voltage and current
requirements.
Note:
This is a grounded plug. To avoid the possibility of electric shock, DO NOT
defeat the ground connection in any way!
CA125D Block Diagram:
effects
line out
master
instrument
channel
input
aux channel
active
piezo
freq cut
filter
gain
low mid cntr
peak
high
rev/
effect
send
vocal/aux
channel
low-z
input
hi-z
input
phantom
power
tones
80 330 1k
Hz
4k 10k
level
graphic EQ
rev/
effect
send
hi-z
input
gain
gain
effect
return
effect
return
master
level
50w
25w
high pass
hi-freq
driver
low-freq
driver
low-freq
driver
reverb
return
effects
send
low-z
bal.
gnd
lift
hi-z
bal.
level
line out
rev/
effect
send
50w
depth rate
chorus
on
off
low pass
foot
switch
DSP
mode
The DSP
Section:
The CA125D features Crate's On-Board Digital Signal Processing
(DSP) technology that was designed specifically for use with acoustic
instruments and vocals. This provides a large selection of digital
reverbs, effects and delays. Select the type of effect desired by rotating
the Mode control (#22). This control is divided into five sections: Small
Area Reverbs (SAR), Large Area Reverbs (LAR), Special Reverbs (SPR),
Delays (DLY) and Multiple Effects (Multi).
The following chart provides a list of the DSP settings along with a brief
description of each effect.
SAR:
Small Room
8' x 8' empty room w/hardwood floor
Small Rehearsal Hall
20' x 40' hall, wood floors, hard walls
LAR:
Large Hall
50' x 100' hall, about 50 persons
Concert Hall
5000-seat hall, full crowd
SPR:
Plate Reverb
Simulates studio steel plate reverb
Spring Reverb
Simulates multi-spring reverb tank
DLY:
Slapback, short
125ms delay + reverb
Slapback, Med-short
240ms delay + reverb
Slapback, Medium
350ms delay + reverb
Slapback, Long
557ms delay - 630' travel time
Multi: Short Med. Surface
280ms delay w/21.8% regen + reverb
Medium Hard Surface
335ms delay w/26.5% regen + reverb
Chor-Delay
400ms delay with modulation
Chor-Verb
Hall reverb w/modulated pre-delay
Slap-Verb
Medium hall w/200ms pre-delay
Instrument Doubler
Simulates second track slightly out-of-sync
SPR
LAR
SAR
DLY
Multi
Mode