background image
Operation Guide 4334
1
MO0607-EB
Warning!
· The measurement functions built into this watch are not intended for use in taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonably accurate representations only.
· CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
About This Manual
· Button operations are indicated using the letters shown
in the illustration.
· For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
· Depending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
· Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
(Light)
General Guide
· Press C to change from mode to mode.
· In any mode, press L to illuminate the display.
Recall Mode
World Time Mode
Stopwatch Modes
Countdown Timer
Mode
Alarm Mode
Press C.
Hand Setting Mode
TimeKeeping Mode
This watch has two
stopwatch modes. See
"Stopwatches" for more
information.
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
This watch features separate digital and analog
timekeeping. The procedures for setting the digital time
and analog time are different.
· See "Thermometer" for details about the thermometer.
Setting the Digital Time and Date
This watch is preset with UTC differential values that
represent each time zone around the globe. Before setting
the digital time, be sure to first set the UTC differential for
your Home Time, which is the location where you normally
will be using the watch.
· Note that World Time mode times are all displayed
based on the time and date settings you configure in the
Timekeeping Mode.
PM indicator
Hour : Minutes
Seconds
Month ­ Day
Thermometer
Day of week
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
· Be sure to configure the correct UTC differential for
your Home Time before configuring any other
Timekeeping Mode settings.
· See the "UTC Differential/City Code List" for
information about the UTC differential settings that are
supported.
2. Press C to move the flashing in the sequence shown
below to select other settings.
l l
ll
lll
lll
ll
l l l
l
Seconds
Hour
UTC
Differential
Minutes
Year
DST
Day
Month
Seconds
Temperature
Unit
12/24-Hour
Format
Temperature Sensor
Calibration
Screen:
To do this:
Reset the seconds to
00
Toggle between Daylight Saving
Time (ON) and Standard Time (OF)
Specify the UTC differential
Change the hour or minutes
Toggle between 12-hour (
12H) and
24-hour (
24H) timekeeping
Do this:
Press D.
Press D.
Use D (+) and B (­).
Use D (+) and B (­).
Press D.
Use D (+) and B (­).
Change the year
Change the month or day
3. When the setting you want to change is flashing, use D and B to change it as
described below.
· The UTC differential setting range is ­12.0 to +14.0, in 0.5-hour units.
· For information about settings other than the time and date, see the following.
Temperature Sensor Calibration: "Thermometer"
Temperature Unit: "Thermometer"
4. Press A to exit the setting screen.
· The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
· The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
· When DST is turned on, the UTC differential setting range is ­11.0 to +15.0, in 0.5-
hour units.
· Any time the seconds setting is changed, the analog hands are adjusted accordingly.
· See "Daylight Saving Time (DST) Setting" below for details about the DST setting.
Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1.In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C once and the DST setting screen appears.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A to exit the setting screen.
· The DST indicator appears on the Timekeeping, Alarm,
and Hand Setting Mode screens to indicate that
Daylight Saving Time is turned on.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
l l
ll
lll
lll
ll
l
l l
l
ll
ll
ll
l
l
l l
l l
DST indicator
On/Off status
To adjust the analog time
1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D to adjust the analog setting.
· Press D once to advance the hands 20 seconds.
· Hold down D to advance the hands at high speed.
· To lock high speed hands movement, hold down D to start it and then press B
to lock. The hands will continue to advance for one 12-hour cycle or until you
press any button to stop it.
High-speed hand movement also will stop automatically after the time advances
12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper)
starts to sound.
4. Press A to exit the setting screen.
· The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
· To return to the Timekeeping Mode, press C.
l l ll
lll
ll
ll
ll
l l
l l l
Stopwatches
Your watch has two stopwatch modes: a Single Stopwatch
Mode and a Dual Stopwatch Mode. Both stopwatch
modes measure times in 1/100-second units for the first
hour, and in 1-second units after that. In both stopwatch
modes, timing is possible up to 99 hours, 59 minutes,
59.99 seconds.
The Single Stopwatch Mode (ST1) displays the total
elapsed time and lap times for a single vehicle or runner.
The Dual Stopwatch Mode (ST2) can be used to measure
elapsed time for two vehicles or runners at the same time,
including separate lap times and the time differential
between vehicles or runners.
The data produced by either stopwatch mode is stored
automatically in watch memory, for later recall when you
need it.
· When the elapsed time being kept by either of the stopwatches exceeds 99 hours,
59 minutes, 59.99 seconds, the displayed time returns to all zeros and time
measurement continues from there. Elapsed time measurement continues until you
reset it to all zeros.
· All of the operations in this section are performed in the stopwatch modes, which
you enter by pressing C.


background image
Operation Guide 4334
2
To select the Single Stopwatch Mode or Dual Stopwatch Mode
In the Stopwatch Mode, press A to toggle the Single Stopwatch Mode and the Dual
Stopwatch Mode.
· You cannot toggle between the Single Stopwatch Mode and Dual Stopwatch Mode
while an elapsed time operation is in progress.
After pressing A to reset the elapsed time to all zeros, press A again to toggle
between stopwatch modes.
· The indicator "ST1" indicates the Single Stopwatch Mode, while "ST2" indicates
the Dual Stopwatch Mode.
Remaining free records
Single Stopwatch
Mode Screen
Dual Stopwatch
Mode Screen
Press A.
L
L
· Both the Single Stopwatch Mode screen and the Dual Stopwatch Mode screen show
the number of free memory records available for storing data. The watch's memory
can hold up to 50 records total, including both Single Stopwatch Mode and Dual
Stopwatch Mode records.
Using the Single Stopwatch Mode
The Single Stopwatch Mode displays the total elapsed time and lap times for a single
vehicle or runner.
Stopwatch mode indicator
To perform a Single Stopwatch Mode operation
1. While the Single Stopwatch Mode screen is displayed,
press D to start elapsed time measurement.
2. To display a lap time, press D while elapsed time
measurement is in progress.
· After about 10 seconds, the upper display will change
automatically to timing of the next lap, with the total
elapsed time shown in the lower display.
· Each press of D during elapsed time measurement
stores the applicable lap number, lap time, and total
elapsed time in memory.
· Lap numbers are displayed in the range of 01 to 99.
After lap 99, pressing D does not display a lap time
(elapsed time continues without stopping).
· During the first hour, the stopwatch displays elapsed time in minutes, seconds,
and 1/100 second. After the first hour, the display changes to shows hours,
minutes, and seconds.
· Use the Recall Mode to view data in memory.
3. To stop elapsed time measurement and reset, press A.
l ll
lll
ll
l l
l ll
lll
ll
l l
l ll
lll
ll
l l
l ll
lll
ll
l l
Total elapsed time
Lap number
Lap time
Using the Dual Stopwatch Mode
The Dual Stopwatch Mode can be used to measure elapsed time for two vehicles or
runners at the same time, including separate lap times and the time differential
between vehicles or runners.
To perform a Dual Stopwatch Mode operation
The table below shows how to time two vehicles or
runners (Measurement A and Measurement B).
· The lower display shows Measurement A, while the
upper display shows Measurement B.
· In the Dual Stopwatch Mode, you can start timing from
either Measurement A or Measurement B.
Measurement B
Measurement A
· The lap number for the current displayed lap time (A or
B) appears in the center left of the display, and the
applicable lap time appears in the upper or lower display.
The other display (upper or lower) shows elapsed time
measurement.
· After about 10 seconds, the display will change
automatically to timing of the next lap.
· Each press of D or B during elapsed time
measurement stores the applicable lap number and lap
time in memory.
l ll
lll
ll
l l
l ll
lll
ll
l l
l ll
lll
ll
l l
l ll
lll
ll
l l
Measurement B Lap Time
Lap number
Measurement A Lap Time
Lap time screen
Start first
elapsed
time.
Press D.
Press B.
Display
lap time
screen.
Press D.
Press B.
Start other
elapsed
time.
Press B.
Press D.
Measurement A
Measurement B
Display lap
time of other
elapsed time.
Press B.
Press D.
Reset
elapsed
time to all
zeros.
Press A.
· Lap numbers are displayed in the range of 01 to 99.
After lap 99, pressing D does not display a lap time
(elapsed time continues without stopping).
· After starting Measurement A or Measurement B
elapsed time measurement and then starting the other
time's elapsed time measurement displaying a lap time
for one of the times will display the other time's lap time
and the difference between Measurement A and
Measurement B. After about 5 seconds, the display will
change automatically to timing of the next lap.
· After you press one of the buttons to display one of the
lap times (without the lap time differential displayed),
pressing the other button displays the other lap time and
the differential between the two laps for about five
seconds.
· The "±" indicator on the lap time differential screen
indicates both times are for the same lap.
· "-'--"--" is shown for the lap time differential if it is greater
than 10 minutes.
l ll
lll
ll
l l
l ll
lll
ll
l l
Measurement B
Lap Time
Measurement A and
Measurement B
differential
· Pressing A stops elapsed time measurement and reset.
· During the first hour, the stopwatch displays elapsed time in minutes, seconds, and
1/100 second. After the first hour, the display changes to shows hours, minutes, and
seconds.
· Use the Recall Mode to view data in memory.
Recalling Stopwatch Data
You can use the Recall Mode to recall and delete
stopwatch data stored in memory.
· Your watch automatically creates logs for storage of
stopwatch data in memory. For information about using
logs, see "Managing Memory Data".
To recall stopwatch log data
1. Enter the Recall Mode.
· The title screen of the newest log appears first when
you enter the Recall Mode.
2. Use the A button to scroll through log title screens
until the one for the log you want to view is on the
display.
· Logs are numbered from 01 (oldest) to 50.
3. Press D (+) or B (­) to view the log data.
Log number
Log title screen
Log creation
date
Stopwatch mode in
which the recalled
log data was
measured
Press B.
Press D.L
L
Best lap indicator
Lap number of
best lap
Best lap
L
L
Lap time
Lap number
L
L
L
L
L
L
*
Total elapsed time
Recalled log data measured in the Single Stopwatch Mode (ST1)
Press B.
Press D.L
L
L
L
L
L
Recalled log data measured in the Dual Stopwatch Mode (ST2)
L
L
Lap time
Lap number
Lap time
Best lap indicator
Best lap
(Measurement A)
*
Best lap
(Measurement B)
L
L
L
One second
later
Lap number of best lap
(Measurement B)
Lap number of best lap
(Measurement A)
* The best lap time is for the best time in the newest log only. The Best Lap Time
screen is the one that has the best lap indicator.
To delete stopwatch data
1. In the Recall Mode, use A to scroll through log title screens until the one for the log
you want to delete is on the display.
· Displaying lap time data (not the log title screen), deleting the data also will delete
the log that contains the data.
2. Hold down B and D until the watch beeps and "
CLR" stops flashing on the
display.
· This will delete all of the data in the currently selected log.
· Deleting the newest log also will delete the best lap time data.
Countdown Timer
You can set the countdown timer within a range of one
minute to 100 hours. An alarm sounds when the
countdown reaches zero.
· You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
· All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Second
Hours
Minutes
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
· When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is reset automatically to its starting value after the alarm stops.
· When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds when the countdown reaches zero.
· The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
· To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
· If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" to
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
l l
l
l
lll
ll
l
l
l l
l l
Auto-repeat on indicator
On/Off status


background image
Operation Guide 4334
3
3. Perform the following operations, depending on which setting is currently selected
on the display.
· While the start time setting is flashing, use D (+) and B (­) to change it.
· Set 0:00 to specify 100 hours.
· While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press
D to toggle auto-repeat on (0N) and off (0F).
4. Press A to exit the setting screen.
· The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
· Frequent use of auto-repeat and the alarm can run down battery power.
Alarm
When the alarm is turned on, the alarm sounds when the
alarm time is reached. You also can turn on an Hourly
Time Signal, which will cause the watch to beep twice
every hour on the hour.
· All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Hourly time signal
on indicator
Alarm on indicator
Alarm time
(Hour : Minutes)
AM indicator
To set the alarm time
1. In the Alarm Mode, hold down A until the hour setting
of the alarm time starts to flash, which indicates the
setting screen.
· This operation turns on the alarm automatically.
2. Press C to move the flashing between the hour and
minute settings.
3. While a setting is flashing, use D (+) and B (­) to
change it.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for 10 seconds, regardless of the mode the watch
is in.
· To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
lll
llll
ll
lll
To turn the daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press D to cycle through the settings shown below.
· The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
Light figures on a dark background
Dark figures on a light background
World Time
The World Time Mode digitally displays the current time in
50 cities (30 time zones) around the world.
· The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check the UTC differential of
your Home Time and the current setting of the
Timekeeping Mode time.
· Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the "UTC Differential/City Code List" for
information about the UTC differential settings that are
supported.
· All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
City code
Current time in
selected city
Date and day of the week
in the selected city
To view the time in another city
While in the World Time Mode, press D to scroll eastward through the city codes
(time zones) or B to scroll westward.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D and B to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
· The DST indicator is shown on the World Time screen
while Daylight Saving Time is turned on.
· Note that changing the Daylight Saving Time for any city
code causes the setting to be applied to all city codes.
DST indicator
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch's auto light switch turns on illumination
automatically when you angle the watch towards your face.
· The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
· See "Illumination Precautions" for other important
information about using illumination.
To turn on illumination manually
In any mode, press L to illuminate the display for about
1.5 seconds.
· The above operation turns on illumination regardless of
the current auto light switch setting.
Auto light switch
on indicator
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode, except for the Hand Setting Mode setting
screen.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
· Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
Warning!
····· Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
····· When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for about three seconds to toggle the auto
light switch on (
displayed) and off (
not displayed).
· The auto light switch on indicator (
) is on the display in all modes while the auto
light switch is turned on.
· In order to protect against running down the battery, the auto light switch will turn off
automatically about six hours after you turn it on. Repeat the above procedure to
turn the auto light switch back on if you want.
· Illumination is always disabled (regardless of the current auto light switch setting)
while an alarm is sounding.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Stopwatch Modes
The following describes how to perform data storage and measurement in the
stopwatch modes.
Managing Memory Data
Pressing the D button in the Single Stopwatch Mode or the D or B button in the
Dual Stopwatch Mode to start a new elapsed time measurement operation creates a
new log in memory.
A new log is created each time you start a new elapsed time measurement operation.
A log contains a log title screen, and records of all the lap times that are recorded
during elapsed time measurement.
· The capacity of the watch's memory is 50 records.
· If you are adding records to the only log in memory and watch memory becomes
full, adding another record causes the oldest record in the log to be deleted
automatically to make room for the new record.
· If you are adding records to a log when there are multiple logs in memory and watch
memory becomes full, adding another record causes the oldest log in memory and
all of its records to be deleted automatically to make room for new records.
How stopwatch data is stored
The following table shows how stopwatch data is stored when you perform stopwatch
button operations.
Single Stopwatch Mode data
Stopwatch
Button Operation
From all-zeros,
press D to start.
Press D to
display lap time.
Press A to stop
elapsed time
measurrement
and reset.
Data Storage Description
Creates a new log (ST1). Stores the date the button was
pressed, and the log number.
Creates a new record with each button operation. Stores the lap
time and total elapsed time at the point the button is pressed.
Resets the elapsed time to all zeros without recording data.
Stopwatch
Button Operation
From all-zeros,
press D or B to
start.
Press D or B to
display lap time.
Press A to stop
elapsed time
measurement
and reset.
Data Storage Description
Creates a new log (ST2). Stores the date the button was
pressed, and the log number.
Creates a new record with each button operation. Stores the lap
time the point the button is pressed.
Resets the elapsed time to all zeros without recording data.
Dual Stopwatch Mode data


background image
Operation Guide 4334
4
Thermometer
· A reading is taken during each even-numbered minute.
· You can select either Celsius (°C) or Fahrenheit (°F) units for the thermometer
screen. See "To specify the temperature display unit" for more information.
· The thermometer screen displays temperature values in 0.1°C units (or 0.2°F units).
· The display range of the thermometer screen is ­10.0°C to 60.0°C (or 14.0°F to
140.0
°F).
· You can calibrate temperature sensor if you feel that the displayed temperature
values are not correct. See "Temperature Sensor Calibration" for more information.
Important!
· Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. To achieve more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It takes
approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
Temperature Sensor Calibration
The temperature sensor built into the watch is calibrated at the factory and normally
requires no further adjustment. If you notice serious errors in the temperature readings
produced by the watch, you can calibrate the sensor to correct the errors.
Important!
Calibrating the temperature sensor can incorrectly result in incorrect readings. read
The following carefully before doing anything.
· Compare the readings produced by the watch with those of another reliable and
accurate thermometer.
· If adjustment is required, remove the watch from your wrist and wait for 20 or 30
minutes to give the temperature of the watch time to stabilize.
To calibrate the temperature sensor
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C nine times to display the temperature sensor
calibration screen.
3. Use D (+) and B (­) to change the calibration value.
· You can change the value in 0.1ºC (0.2ºF) steps, in a
range of ±10ºC (±18ºF). The calibration value shows
``
--.-'' when the setting is outside the allowable range.
· To return the calibration value to its default (no calibration, indicated by ``- -''),
press D and B at the same time.
· Temperature sensor calibration will not be possible if the current reading is
outside the allowable display range (­10.0
°C/14.0°F to 60.0°C/140.0°F) and the
calibration value shows ``- -''.
· Setting a sensor calibration value does not affect temperature values that are
already stored in memory.
4. After configuring the setting you want, press A to exit the setting screen.
llll
lll
lll
l l
Calibration value
To specify the temperature display unit
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C 10 times to display the temperature unit
setting screen.
3. Use D to switch between Celsius (
°C) and Fahrenheit
(
°F).
· The initial factory default and the initial default after
battery replacement is Celsius (
°C).
4. After configuring the setting you want, press A to exit the setting screen.
· The temperature display unit setting you select also is applied to temperature values
that are already stored in memory.
Auto Return Feature
· If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch saves any settings you have made up to
that point and exits the setting screen automatically.
l ll
llll
lll
ll
ll l
Temperature unit
· The watch will change to the Timekeeping Mode automatically if you do not perform
any operation in the Recall Mode, Alarm Mode, or Hand Setting Mode for two or
three minutes.
Button Operation Tone
In any mode (except when a setting screen is on the display), hold down C for about
three seconds to toggle the button operation tone on and off. The button operation
tone off indicator (
) is displayed while the tone is turned off.
· Even if the button operation tone is turned off, the daily alarm and countdown timer
alarm continue to sound when required.
Data and Setting Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
· Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
00 without changing the minutes.
· With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
· With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
· The year can be set in the range of 2000 to 2099.
· The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch's batteries replaced.
· The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
· UTC is the abbreviation for Coordinated Universal Time, which is the world-wide
scientific standard of timekeeping. It is based upon carefully maintained atomic
(cesium) clocks that keep time accurately to within microseconds. Leap seconds are
added or subtracted as necessary to keep UTC in sync with the Earth's rotation.
World Time
· The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
· All World Time Mode times are calculated from the current time in the Timekeeping
Mode using UTC time differential values.
Illumination Precautions
· The electro-luminescent panel that provides illumination loses power after very long
use.
· Illumination may be hard to see when viewed under direct sunlight.
· The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
· Illumination turns off automatically whenever an alarm sounds.
· Frequent use of illumination runs down the batteries.
Auto light switch precautions
· Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
More than 15 degrees
too high
· Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
· Illumination turns off in about one second, even if you
keep the watch pointed towards your face.
· Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
· Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
· You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Pago Pago
Honolulu
Anchorage
Vancouver
San Francisco
Los Angeles
Denver
Mexico City
Chicago
Miami
New York
Caracas
St. Johns
Rio De Janeiro
Praia
Lisbon
London
City
City
UTC
Other major cities in same time zone
Code
Differential
UTC Differential/City Code List
PPG
HNL
ANC
YVR
SFO
LAX
DEN
MEX
CHI
MIA
NYC
CCS
YYT
RIO
RAI
LIS
LON
­11.0
­10.0
­09.0
­08.0
­07.0
­06.0
­05.0
­04.0
­03.5
­03.0
­01.0
+00.0
Papeete
Nome
Las Vegas, Seattle/Tacoma, Dawson City
Edmonton, El Paso
Huston, Dallas/Fort Worth, New Orleans, Winnipeg
Montreal, Detroit, Boston,
Panama City, Havana, Lima, Bogota
La Paz, Santiago, Port Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
Dublin, Casablanca, Dakar, Abidjan
Barcelona
Paris
Milan
Rome
Berlin
Athens
Johannesburg
Istanbul
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Male
Delhi
+01.0
+02.0
+03.0
+03.5
+04.0
+04.5
+05.0
+05.5
Amsterdam, Algiers, Hamburg, Frankfurt, Vienna, Madrid,
Stockholm
Helsinki, Beirut, Damascus, Cape Town
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi
Shiraz
Abu Dhabi, Muscat
Mumbai, Kolkata
BCN
PAR
MIL
ROM
BER
ATH
JNB
IST
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
MLE
DEL
Dhaka
Yangon
Bangkok
Jakarta
Singapore
Hong Kong
Beijing
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
Nuku'Alofa
+06.0
+06.5
+07.0
+08.0
+09.0
+09.5
+10.0
+11.0
+12.0
+13.0
Colombo
Phnom Penh, Hanoi, Vientiane
Kuala Lumpur, Taipei, Manila, Perth, Ulaanbaatar
Pyongyang
Darwin
Melbourne, Rabaul
Port Vila
Christchurch, Nadi, Nauru Island
DAC
RGN
BKK
JKT*
SIN*
HKG
BJS
SEL
TYO
ADL
GUM
SYD
NOU
WLG
TBU
· Based on data as of June 2005.
* The sequence of these city codes is SIN
JKT.