background image
2017-1
Module No.2017
TIMEKEEPING MODE
The settings you make in the Timekeeping Mode are very important, because they
affect the Moon Data, Tide Graph, and Sunrise/Sunset functions.
There are three setting screens in the Timekeeping Mode: the Time and Date Setting
Screen, DST, GMT Differential, Point Name Setting Screen, and Longitude/Latitude,
Lunar Tide Interval Setting Screen.
· For normal timekeeping, you need to set the time, and date, and turn daylight
saving time (summer time) on or off.
· To use the Moon Data, Tide Graph, and Sunrise/Sunset functions, you must set the
GMT differential, your current longitude and latitude, and the lunar tide interval on
your point.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
To set the time and date
· Use this screen to set the current time and date, to
reset the seconds to 00, and to toggle between 12-hour
and 24-hour timekeeping.
1. In the Timekeeping Mode, check if the DST indicator is
displayed, and change the DST setting in accordance
with the timekeeping in your area.
· Turn on DST if daylight saving time (summer time) is
currently in effect in your area. If daylight saving time is
not currently in effect in your area, be sure to turn DST
off.
· See "To turn DST on and off" for details about turning
DST on and off.
2. In the Timekeeping Mode, hold down A
A
A
A
A until the
seconds digits start to flash. This is the Time and Date
Setting Screen.
3. Press C
C
C
C
C to move the selection around the display in the following sequence.
4. While the seconds digits are selected (flashing), press D
D
D
D
D to reset the seconds to
00. If you press D
D
D
D
D while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
5. While any other digits (besides seconds), are selected (flashing), press D
D
D
D
D to in-
crease the number or B
B
B
B
B to decrease it. Holding down either button changes the
current number at high speed.
· While the 12/24-hour setting is selected, press D
D
D
D
D to switch between the two
formats.
· The day of the week is automatically set in accordance with the date.
· The date can be set with the range of January 1,1995 to December 31, 2039.
6. After you are finished making the settings you want, press A
A
A
A
A to advance to the
DST, GMT Differential, Point Name Setting Screen. To return to the normal Time-
keeping Mode screen, press A
A
A
A
A three times.
DST, GMT Differential, Point Name Setting Screen
Use this screen to switch DST (daylight saving time or
summer time) on and off, to specify the GMT differential
from your current location and to input new point names.
To turn DST on and off
While ON or OFF and the small DST mark are flashing on the display, press D
D
D
D
D to
toggle DST on and off.
Important!
· Be sure to use this procedure to turn daylight saving time (summer time) on and off.
Never manually change the timekeeping setting to adjust for daylight saving time.
Doing so will produce incorrect Moon Data, Tide Graph, and Sunrise/Sunset data.
Use C
C
C
C
C to move the flashing to the GMT differential value.
To set the GMT differential
Notes
· The GMT differential is the difference in time between the time zone where you are
currently located and Greenwich Mean Time (GMT).
· See "TIME ZONE CHART" at the back of this manual for information about deter-
mining the GMT differential in your area.
1. Press D
D
D
D
D to increase the value or B
B
B
B
B to decrease it. Holding down either button
changes the setting at high speed.
2. Use C
C
C
C
C to move the flashing to the first character of the point name.
MULTI-TIME MODE
To view point data
1. In the Timekeeping Mode, press B
B
B
B
B to enter the Multi-time Mode. The first point
that appears is the one you selected as your home time point.
2. Press B
B
B
B
B to scroll through the data for the 10 points. The watch beeps and returns
to the Timekeeping Mode after the tenth point.
· Pressing C
C
C
C
C at any time in the Multi-time Mode immediately returns to the Time-
keeping Mode.
· You can use the procedure under "DST, GMT Differential, Point Name Setting
Screen" and "Longitude/Latitude, Lunar Tide Interval Setting Screen" to change
the name and other data of a point.
This watch comes pre-programmed with data for 10 dolphin or whale watching points
around the world. The data for each point includes an 8-character point name, GMT
differential, longitude and latitude, and lunar tide interval. Setting the current time
and date for any of the points causes the time and date settings for all other points to
be adjusted accordingly. In the case of DST, however, you must make a separate
setting for each point. You can use the following procedure to select any one of the
ten points as your home time point.
· See the "PRESET LOCATION CHART" at the back of this manual for details on
the locations whose data is preset in watch memory when you purchase it.
To select a point for your home time
· While the point you want to use for your home time is displayed in the Multi-time
Mode, hold down D
D
D
D
D for about two seconds.
Multi-time Mode
Point name
Home time
Local time
GENERAL GUIDE
· If the digital display of your watch is continually changing, see "About Auto Display" for information on how to stop it.
· Press C
C
C
C
C to change from mode to mode. After you perform an operation in Countdown Alarm Mode or Stopwatch Mode, pressing C
C
C
C
C returns to the Timekeeping Mode.
· In the Timekeeping Mode, press D
D
D
D
D to illuminate the display for about two seconds.
Timekeeping Mode
Moon Data Mode
Sunrise/Sunset Mode
Countdown Alarm Mode
Stopwatch Mode
Alarm Mode
Day of week
Tide graph
Moon graph
Month - Day
Seconds
Hour
PM indicator
Point name
DST ON/OFF
GMT differential
Seconds
Hour
Minutes
12/24-Hour
Format
Day
Year
Month
Latitude
Longitude
Lunar tide interval
DST
ON/OFF
GMT
differential
1st
character
2nd
character
8th
character
Point name
To change a point name
1. Press D
D
D
D
D to scroll forward through the characters at the current flashing location, or
B
B
B
B
B to scroll backwards. Holding down either button changes the current characters
at high speed.
2. When the character you want is displayed, press C
C
C
C
C to advance to the next
character.
3. Repeat steps 1 and 2 for all eight characters of the point name.
· After you are finished making the settings you want, press A
A
A
A
A to advance to the
Longitude/Latitude, Lunar Tide Interval Setting Screen.
Longitude/Latitude, Lunar Tide Interval Setting Screen
Use this screen to specify the longitude, latitude, and
lunar tide interval of your current location.
To set the longitude and latitude of your current location
While the Longitude/Latitude is flashing on the display, use D
D
D
D
D to change the
longitude value and B
B
B
B
B to change the latitude value.
· After you are finished making the settings you want, press C
C
C
C
C to advance to the
Lunar Tide Interval Setting Screen.
To set the lunar tide interval at your current location
1. Press D
D
D
D
D to increase the hour value or B
B
B
B
B to decrease it. Holding down either button
changes the setting at high speed.
2. Press C
C
C
C
C to move to the minutes digits.
3. Press D
D
D
D
D to increase the minutes value or B
B
B
B
B to decrease it.
4. After you are finished making the settings you want, press A
A
A
A
A to return to the
normal Timekeeping Mode Screen.
About the lunar tide interval
The lunar tide interval is the period from the moon's upper transit (moon up) to high
tide. If you know the lunar tide interval, tide changes can be determined using the
moon age. This watch calculates tide changes according to the current time and the
location setting, and displays them graphically.
To calculate the lunar tide interval
1. Look up the high tide time for the flood tide of the location whose tide changes you
want to know.
2. Use this watch to look up the moon up time that occurs immediately before this
time.
3. Subtracting the moon up time from the high tide time produces the lunar tide inter-
val.
Longitude/Latitude
Luner tide interval
Minutes
Hour
Lunar tide interval
Minutes


background image
2017-2
BACKLIGHT
The backlight uses an EL (electro-luminescent) panel that
cause the entire display to glow for easy reading in the
dark. The watch's auto light switch automatically turns on
the backlight when you angle the watch towards your face.
· The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
Note
· The electro-luminescent panel loses illuminating power
after very long use.
· The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
· The watch will emit an audible sound whenever the display is illuminated. This is
caused by vibration of the EL panel when it is lit. It does not indicate malfunction of
the watch.
· The backlight automatically turns off whenever an alarm sounds.
To manually turn on the backlight
· In the Timekeeping Mode, press D
D
D
D
D to illuminate the display for about two seconds.
· The above operation turns on the backlight regardless of the current auto light switch
setting.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on whenever you posi-
tion your wrist as described below. Note that the auto light switch of this watch will
operate only when available light is below a certain level. It does not turn on the
backlight under bright light.
· Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life.
· The backlight turns off in about two seconds, even if you keep the watch pointed
towards your face.
· The backlight may not light if the face of the watch is more than 15 degrees off the
parallel as shown below. Make sure that the back of your hand is parallel to the
ground.
· Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If the backlight does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
· Under certain conditions the backlight may not light until about one second or less
after turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
Warning!
· Never try to read your watch when mountain climbing or hiking in areas that
are dark or in areas with poor footing. Doing so is dangerous and can result
in serious personal injury.
· Never try to read your watch when running where there is danger of acci-
dents, especially in locations where there might be vehicular or pedestrian
traffic. Doing so is dangerous and can result in serious personal injury.
· Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result
in a traffic accident and serious personal injury.
· When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal inju-
ry.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D
D
D
D
D for one second to turn the auto light switch
on (AUTO
displayed) and off (AUTO
not displayed).
· Frequent use of the auto light switch greatly reduces the charge of the storage
battery. If you use the auto light switch often, be sure to leave the watch where it is
exposed to sunlight during the day time so it can recharge the storage battery. 10
minutes exposure to sunlight provides enough of a charge for about 10 to 20 auto
light switch operations.
· The AUTO
indicator is on the display in all modes while the auto light switch is
turned on.
MOON DATA MODE
Be sure to set the current time and your current location before trying to use the
Moon Data Mode.
The Moon Data Mode display shows the current moon age, as well as moon up and
moon down times. Moon age is indicated both by a value and one of the following
graphics.
· The moon up time indicates when the moon will
reach its highest point relative to your current lo-
cation (upper transit), while the moon down time
indicates when it will reach its lowest point (low-
er transit). Note that moon up and moon down
times are accurate up to
±30 minutes.
To display the moon up and moon down time for a specific date
· The moon data for your home time point appears first
when you enter the Moon Data Mode.
· Press D
D
D
D
D (forward) or B
B
B
B
B (back) within about two
seconds after entering the Moon Data Mode to scroll to
another point. Holding down either button scrolls at high
speed. It takes about 40* seconds before moon data
appears after you display the name of a point.
· If you do not perform any button operation, about two
seconds after you enter the Moon Data Mode the
display changes automatically to show the moon data
for today's date. Pressing D
D
D
D
D advances to the next date,
while B
B
B
B
B goes back to the previous date. Holding down
either button scrolls the date at high speed. It takes about
40* seconds before moon data appears after you dis-
play a date.
* While the countdown alarm is operating, it takes about
three and a half minutes to calculate.
· Note that once you enter the moon data display, you
cannot change to another point. To change to another
point, press A
A
A
A
A twice to return to the point name
display, make the changes you want, and then re-enter
the moon data display.
· Moon data is displayed in 5-minute units.
· For days around the full moon (moon age 15) or new
moon (moon age 29.5), there are days where there is
no moon up or moon down. In such cases, the xx:xx
is shown for the moon up or moon down time.
Moon
Moon
Location
Earth
Moon-UP
Moon-Down
TIDE GRAPH MODE
1. Press A
A
A
A
A while in the Moon Data Mode to enter the Tide
Graph Mode. The display shows the tide graph for 6:00
am on the date that was selected in the Moon Data
Mode.
2. Use D
D
D
D
D (forward) and B
B
B
B
B (back) to scroll the time in 1-
hour increments. Holding down either button changes
the time at high speed.
· Note that once you enter the Tide Graph Mode, you
cannot change to another point or date. To change to
another point or date, press A
A
A
A
A to return to the Moon
Data Mode, make the changes you want, and then
re-enter the Tide Graph Mode.
SUNRISE/SUNSET MODE
· The today's sunrise and sunset data for your home time
point appears first when you enter the Sunrise/Sunset
Mode.
· Press D
D
D
D
D (forward) or B
B
B
B
B (back) within about two
seconds after entering the Sunrise/Sunset Mode to scroll
to another point. Holding down either button scrolls at
high speed. It takes about 40* seconds before sunrise/
sunset data appears after you display the name of a
point.
· If you do not perform any button operation, about two
seconds after you enter the Sunrise/Sunset Mode the
display changes automatically to show the sunrise/
sunset data for today's date. Pressing D
D
D
D
D advances to
the next date, while B
B
B
B
B goes back to the previous date.
Holding down either button scrolls the date at high speed.
It takes about 40* seconds before sunrise/sunset data
appears after you display a date.
* While the countdown alarm is operating, it takes about
three and a half minutes to calculate.
· Note that once you enter the Sunrise/Sunset data display, you cannot change to
another point. To change to another point, press A
A
A
A
A to return to the point name
display, make the changes you want, and then re-enter the Sunrise/Sunset data
display.
· Sunrise/sunset data is displayed in 5-minute units.
Auto light switch
on indicator
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes the backlight to light.
Parallel to ground
More than
40
°
Parallel to ground
More than 15 degrees
too high
More than 15 degrees
too low
New Moon Crescent
Moon
Half Moon
First Quarter
Full Moon
Half Moon
Last Quarter
Point name
Hour
Minutes
Moon age
Moon down
time
Moon up time
Year
Month
Day
High
Ebb
Tide graph
Day of week
Month - Day
Time
Low Flood
Point name
Hour
Minutes
Sunset time
Sunrise time


background image
2017-3
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 1 second to 24 hours. When the
countdown reaches zero, an alarm sounds for 10 seconds or until you press any
button.
To set the countdown start time and to switch auto repeat timing on and off
1. Hold down A
A
A
A
A while in the Countdown Alarm Mode. The
minutes digits flash on the display because they are
selected.
2. Press C
C
C
C
C to change the selection in the following
sequence.
3. While the hour, minutes, or seconds digits are flashing, press D
D
D
D
D to increase the
value or B
B
B
B
B to decrease it. Holding down either button changes the value at high
speed.
4. While the auto repeat indicator is flashing, press D
D
D
D
D toggle auto repeat on and off.
The auto repeat indicator is on the display only while you are setting the count-
down start time.
· To set the starting value of the countdown time to 24 hours, set 0:00' 00".
5. After you set the countdown start time and auto repeat timing on and off, press A
A
A
A
A
to return to the Countdown Alarm Mode.
To use the countdown alarm
1. Press D
D
D
D
D while in the Countdown Alarm Mode to start the countdown alarm.
2. Press D
D
D
D
D again to stop the countdown alarm.
· You can resume countdown alarm operation by pressing D
D
D
D
D.
3. Press D
D
D
D
D to stop the countdown alarm, and then press B
B
B
B
B to reset the countdown
time to its starting value.
· When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button. Count-
down timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.
To turn the progress beeper on and off
1. While the Countdown Alarm Mode screen shows its starting value or while a count-
down operation is in progress, press B
B
B
B
B to toggle the progress beeper on and off.
· When the end of the countdown is reached while auto repeat is on, the alarm sounds,
but the countdown restarts from the beginning without stopping. You can stop the
countdown by pressing D
D
D
D
D and manually reset to the start time by pressing B
B
B
B
B.
· If you set a starting time of 10 seconds or less and have Auto Repeat turned on, the
countdown alarm tone (which normally sounds for 10 seconds) sounds for only one
second.
· When the progress beeper is turned on, the watch beeps as the countdown time
passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1-second marks.
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes 59.99 seconds.
· Pressing A
A
A
A
A in the Stopwatch Mode while an elapsed
time operation is in progress or while an elapsed time
(other than all zeros) is stopped on the display causes
the upper right display to alternate between the current
time and stopwatch time.
Elapsed time measurement
Start
Stop
Re-start
Stop
Clear
Start
Split
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split time measurement
Split time and 1st-2nd place times
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
Countdown Start
In addition to the normal instant start at the press of a button, the stopwatch can also
be set up to start timing automatically after five seconds have elapsed.
· While the stopwatch is stopped and cleared to all zeros, press A
A
A
A
A to toggle count-
down start on and off. Turning on countdown start displays 5" in the lower part of
the display. 00' 00" 00 is displayed when countdown start is turned off. The upper
part of the display always shows the current time.
ALARM MODE
You can set five independent alarms with the hour,
minutes, month and day. Use the Alarm Mode to turn the
alarm and the Hourly Time Signal on and off.
· When an alarm is turned on, an alarm tone sounds for
20 seconds when the preset time reached.
· When the Hourly Time Signal is turned on, the watch
beeps every hour on the hour.
Alarm types
The types of alarm you get depends on the information
you set.
· To set a daily alarm
Set the hour and minutes for the alarm time. Set "x" for
the month and "xx" for the day. This type of setting
causes the alarm to sound everyday at the time you set.
· To set a date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
· To set a 1-month alarm
Set the month, hour and minutes for the alarm time. Set "xx" for the day. This type
setting causes the alarm to sound every day at the time you set, only during the
month you set.
· To set a month alarm
Set the day, hour and minutes for the alarm time. Set "x" for the month. This type of
the setting causes the alarm to sound every month at the time you set, on the day you
set.
To set the alarm time
1. Press D
D
D
D
D while in the Alarm Mode to select Alarm 1 through Alarm 5 and Hourly
Time Signal.
2. After you select an alarm, hold down A
A
A
A
A until the hour digits start to flash on the
display. The hour digits flash because they are
selected. At this time the alarm is
automatically switched on.
3. Press C
C
C
C
C to change the selection in the following sequence.
4. Press D
D
D
D
D to increase the number or B
B
B
B
B to decrease it. Holding down either button
changes the current number at high speed.
· The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
5. After you set the alarm time, press A
A
A
A
A to return to the Alarm Mode.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
· Press any button to stop the alarm after it starts to sound.
To switch an alarm on and off
1. In the Alarm Mode, press D
D
D
D
D to select an alarm.
2. When an alarm you want to is selected, press B
B
B
B
B to
switch it on and off.
· The individual alarm indicators let you see at a glance
the on/off status of each alarm. The meaning of these
indicators depends on the mode you are in.
· The general alarm indicator is displayed in all modes.
To switch the Hourly Time Signal on and off
1. In the Alarm Mode, press D
D
D
D
D to select the Hourly Time
Signal.
2. When Hourly Time Signal is selected, press B
B
B
B
B to switch
it on and off.
· If Hourly Time Signal is on, the Hourly Time Signal On
indicator is shown on the display when you change to
another mode.
To test the alarm
Hold down D
D
D
D
D while in the Alarm Mode to sound the alarm.
Alarm 1
Alarm 3
Alarm 2
Hourly Time Signal
Alarm 4
Alarm 5
Mode indicator Hour
1/10 second
Seconds
Minutes
Minutes
Auto repeat on/off
Seconds
Hour
Press B
B
B
B
B
Auto repeat OFF
Auto repeat ON
OFF
ON
Mode indicator
Hours
1/100
second
Minutes
Seconds
Countdown start on
General alarm on indicator
Hour
Minutes
Day
Month
Alarm number
Individual
alarm on
indicator
Mode
indicator
Hour
Minutes
Month
Day
Alarm number
Individual alarm
on indicator
General alarm on indicator
AL-1
AL-2
AL-3
Individual alarm
on indicator
AL-4
AL-5
Hourly time signal on
indicator
BATTERY
This watch is equipped with a solar cell and a storage
battery (secondary battery) that is charged by the electri-
cal power produced by the solar cell.
· The area outside of the LCD digital areas is a solar cell
panel that picks up available light to charge the storage
battery.
· A sleep Mode is provided to conserve battery power.
Battery power
indicator


background image
2017-4
[Sleep Mode]
Important!
· Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause storage battery pow-
er to run down. Be sure that the watch is normally exposed to light whenever possi-
ble.
· This watch employs a solar cell that converts light into electricity that charges a
built-in storage battery. Normally, the storage battery should not need replacement,
but after very long use over a number of years, the storage battery may lose its
ability to achieve a full charge. Should you notice problems with getting the storage
battery to a full charge, contact your dealer or CASIO distributor about having the
storage battery replaced.
· The storage battery should be replaced with a CASIO-specified, ML-2020 battery
only. Other storage batteries can cause damage to the watch.
· Be sure to put the watch into its Sleep Mode and keep in an area normally exposed
to light when storing it for long periods. This helps to keep the storage battery from
going dead.
Battery Power Indicator
The battery power indicator on the display shows you the current status of the stor-
age battery's power.
· At Level 4, the display is disabled but timekeeping and other functions continue to
operate internally. Pressing any button causes the Timekeeping Mode screen to
appear for two or three minutes.
· At Level 5, all functions are disabled. Functions are enabled once again after the
storage battery is charged, but anything previously stored in memory is lost. Be-
cause of this, you must set the current time and alarms, and re-input point data
after the storage battery is charged.
· Leaving the watch under strong direct sunlight to charge can cause the battery
indicator to show a battery capacity reading that is higher than the actual level.
Check the level after leaving the watch in an area out of the sun for a few minutes.
Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its storage battery.
Warning!
Leaving the watch in sunlight to charge its storage battery can cause it to be-
come quite hot. Take care when handling the watch to avoid burn injury.
Avoid charging the battery in the high temperature conditions described be-
low.
· On the dashboard of a car parked in direct sunlight.
· Too close to an incandescent lamp.
· Under direct sunlight or in any other area exposed to intense heat for long periods.
Charging Guide
Required charge time when the backlight is used for two seconds and the alarm
sounds for 20 seconds per day:
· Approximately 8 hours of 500 lux (indoor fluorescent lighting) per day
· Approximately 1 hour 20 minutes of 3,000 lux (direct fluorescent lighting) per day
· Approximately 50 minutes of 36,000 lux (afternoon outdoor sunlight) per week (7
minutes per day)
Required charge time when the backlight is used for 30 seconds and the alarm sounds
for 20 seconds per day:
· Approximately 4 hours of 3,000 lux (direct fluorescent lighting) per day
· Approximately 2 hours 20 minutes of 36,000 lux (afternoon outdoor sunlight) per
week (20 minutes per day)
Using the Sleep Mode
In any mode (except while figures are flashing on the dis-
play for input), hold down C
C
C
C
C for about two seconds.
· This enters the Sleep Mode, which clears the display.
Time keeping and other functions continue to be per-
formed internally.
· Alarms, the Hourly Time Signal, and the backlight are
disabled while the watch is in the Sleep Mode.
· Pressing any button (except A
A
A
A
A) exits the Sleep Mode
and enters the Timekeeping Mode.
About Auto Display
Auto Display is a demonstration feature that continually changes the contents of the
digital display. Note that you cannot use any of the watch's other functions while Auto
Display is operating.
To turn off Auto Display
Hold down A
A
A
A
A for about two seconds until the watch beeps.
To turn on Auto Display
1. In any mode (except while figures are flashing on the display for input), hold down
C
C
C
C
C for about two seconds to enter the Sleep Mode.
2. Hold down A
A
A
A
A for about two seconds until the watch beeps. This indicates that Auto
Display is on.
· You cannot turn on Auto Display while a setting screen (indicated by flashing digits)
is on the display.
· Leaving the watch in a dark area can cause Auto Display operation to stop. Normal
operation should resume when the watch is again exposed to light.
· Auto Display cannot be turned on while the storage battery is at Level 4 or Level 5.
Auto Display also turns off automatically whenever the storage battery drops to
Level 4 or Level 5.
Point name
Longitude
Latitude
OGASAWARA
142
° E27° N
9
6:30
MORETON
153
° E27° S
10
10:00
MAUI
157
° W21° N
­10
4:00
VANCOUVER
126
° W50° N
­8
1:00
BAJA CA
110
° W24° N
­7
8:50
BAHAMAS
79
° W27° N
­5
7:40
CANARY IS
17
° W28° N
0
0:00
CORSICA
9
° E43° N
1
9:00
ZANZIBAR
39
° E6° S
3
3:30
BALI
115
° E9° S
8
10:50
GMT
differential
Lunar Tide
Interval
PRESET LOCATION CHART
OGASAWARA
CORSICA
s MAUI
BAHAMAS
s
MORETON
VANCOUVER
CANARY IS
s
s
s
s
s ZANZIBAR
s
s
s
BAJA CA
BALI
OGASAWARA Area around Chichijima Island, which is one of the Ogasawara Is-
lands located about 1,000 kilometers south of Tokyo.
MORETON
Area around Moreton Island, located just off Brisbane, Australia.
MAUI
Area around Maui, located northwest of Hawaii Island.
VANCOUVER Area around Johnstone Strait, Vancouver, Canada.
BAJA CA
Area around the central part of the Baja Peninsula, located south
of California in Mexico.
BAHAMAS
Area around the Little Bahama Bank, located north of the Grand
Bahama Island.
CANARY IS
Area around Gomera Island, which is part of the Canary Islands
(Spain).
CORSICA
Ligurian Sea, located north of Corsica (France).
ZANZIBAR
Area off of Zanzibar, Tanzania.
BALI
Area around Bali, Indonesia.
Level
Indicator
Functional Status
1
All functions enabled.
2
All functions enabled.
3
Alarms, Hourly Time Signal, backlight disabled.
4
5
Alarms, Hourly Time Signal, backlight, display
disabled; timekeeping enabled.
Alarms, Hourly Time Signal, backlight, display,
timekeeping disabled.


background image
2017-5
North America
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
1. PAGO PAGO
­11 171°W
14°N
2. HONOLULU
­10 158°W
21°N
3. ANCHORAGE
­9
150°W
61°N
4. NOME
­9
165°W
65°N
5. LOS ANGELES
­8
118°W
34°N
6. SAN FRANCISCO ­8
122°W
38°N
7. LAS VEGAS
­8
115°W
36°N
8. VANCOUVER
­8
123°W
49°N
9. SEATTLE
­8
122°W
48°N
10. DENVER
­7
105°W
40°N
11. EL PASO
­7
106°W
32°N
12. EDMONTON
­7
114°W
54°N
13. CHICAGO
­6
88°W
42°N
14. HOUSTON
­6
95°W
30°N
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE
LATITUDE
15. DALLAS/FORT WORTH ­6
97°W
33°N
16. NEW ORLEANS
­6
90°W
30°N
17. WINNIPEG
­6
97°W
50°N
18. MEXICO CITY
­6
99°W
19°N
19. NEW YORK
­5
74°W
41°N
20. MONTREAL
­5
74°W
45°N
21. DETROIT
­5
83°W
42°N
22. MIAMI
­5
80°W
26°N
23. BOSTON
­5
71°W
42°N
Add 1 hour to the difference time if DST
(Daylight Saving Time) is used. (EX. if difference
of standard time is +2, that of DST is +3.)
180
°
165
°
150
°
135
°
120
°
105
°
90
°
75
°
180
°
165
°
0
°
15
°
60
°
45
°
60
°
45
°
30
°
15
°
.
. .
.
.
.
.
.
.
.
..
.
.
.
.
.
..
. .
.
1
2
3
4
12
8
9
6
5
7
.
10
11 15
14
18
22
16
21
13
19
23
20
17
TIME ZONE CHART
Central and South America
0
°
15
°
30
°
105
°
90
°
75
°
60
°
45
°
45
°
1
2
3
4
5
7
10
6
11
1
12
9
8
.
.
. .
.
.
.
.
.
.
..
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
1. PANAMA CITY
­5
80°W
9°N
2. LIMA
­5
77°W
12°S
3. BOGOTA
­5
74°W
5°N
4. CARACAS
­4
67°W
10°N
5. LA PAZ
­4
68°W
17°S
6. SANTIAGO
­4
71°W
33°S
7. PORT OF SPAIN
­4
61°W
11°N
8. RIO DE JANEIRO ­3
43°W
23°S
9. SAO PAULO
­3
47°W
24°S
10. BRASILIA
­3
48°W
16°S
11. BUENOS AIRES
­3
58°W
35°S
12. MONTEVIDEO
­3
56°W
35°S
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE
LATITUDE
Add 1 hour to the difference time if DST
(Daylight Saving Time) is used. (EX. if difference
of standard time is +2, that of DST is +3.)
Europe
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
1. AZORES
­1
25°W
38°N
2. LONDON
+0
0°E
51°N
3. DUBLIN
+0
6°W
53°N
4. CASABLANCA
+0
8°W
34°N
5. LISBON
+0
9°W
39°N
6. PARIS
+1
2°E
49°N
7. MILAN
+1
9°E
45°N
8. ROME
+1
12°E
42°N
9. MADRID
+1
4°W
40°N
10. AMSTERDAM
+1
5°E
52°N
11. HAMBURG
+1
10°E
54°N
12. FRANKFURT
+1
9°E
50°N
13. VIENNA
+1
16°E
48°N
14. STOCKHOLM
+1
18°E
59°N
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
15. ATHENS
+2
24°E
38°N
16. HELSINKI
+2
25°E
60°N
17. ISTANBUL
+2
29°E
41°N
Add 1 hour to the difference time if DST
(Daylight Saving Time) is used. (EX. if difference
of standard time is +2, that of DST is +3.)
.
.
.
. .
. . .
. .
.
.
.
.
.
.
17
15
13
8
7
6
9
5
4
12
11
16
14
10
2
3
.
1
15
°
0
°
15
°
30
°
45
°
45
°
60
°
Africa and Middle East
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
1. BEIRUT
+2
35°E
34°N
2. DAMASCUS
+2
36°E
33°N
3. CAPE TOWN
+2
18°E
34°S
4. KUWAIT
+3
48°E
29°N
5. RIYADH
+3
47°E
25°N
6. JEDDAH
+3
39°E
21°N
7. ADEN
+3
45°E
13°N
8. ADDIS ABABA
+3
39°E
9°N
9. NAIROBI
+3
37°E
1°S
10. DUBAI
+4
55°E
25°N
11. ABU DHABI
+4
54°E
24°N
12. MUSCAT
+4
58°E
23°N
13. KARACHI
+5
67°E
25°N
14. PRAIA
­1
23°W
15°N
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
15. DAKAR
+0
17°W
15°N
16. ABIDJAN
+0
4°W
5°N
Add 1 hour to the difference time if DST
(Daylight Saving Time) is used. (EX. if difference
of standard time is +2, that of DST is +3.)
30
°
75
°
60
°
45
°
30
°
15
°
0
°
15
°
30
°
15
°
0
°
15
°
9
8
7
6
5
4
1
3
2
1
15
14
13
12
1
11
10
16
.
.
.
.
.
.
.
.. . .
. .
.
..
Asia and South Pacific
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE LATITUDE
1. DHAKA
+6
90°E
24°N
2. BANGKOK
+7
100°E
14°N
3. JAKARTA
+7
107°E
6°S
4. PHNOM PENH
+7
105°E
12°N
5. HANOI
+7
106°E
21°N
6. VIENTIANE
+7
103°E
18°N
7. HONG KONG
+8
114°E
22°N
8. SINGAPORE
+8
104°E
1°N
9. KUALA LUMPUR +8
102°E
3°N
10. BEIJING
+8
116°E
40°N
11. TAIPEI
+8
122°E
25°N
12. MANILA
+8
121°E
15°N
13. PERTH
+8
116°E
32°N
14. ULANBATOR
+8
107°E
48°N
15. TOKYO
+9
140°E
36°N
NO.
CITY
THE DIFFERENCE
FROM GMT FOR
STANDARD TIME
LONGITUDE
LATITUDE
16. SEOUL
+9
127°E
38°N
17. PYONGYANG
+9
126°E
39°N
18. SYDNEY
+10 151°E
34°S
19. MELBOURNE
+10 145°E
38°S
20. GUAM
+10 145°E
13°N
21. NOUMEA
+11 166°E
22°S
22. PORT VILA
+11 168°E
18°S
23. WELLINGTON
+12 175°E
41°S
24. CHRISTCHURCH +12 173°E
43°S
25. NADI
+12 178°E
18°S
26. NAURU ISLAND
+12 166°E
1°S
27. PAPEETE
­10 150°W
18°S
Add 1 hour to the difference time if DST
(Daylight Saving Time) is used. (EX. if difference
of standard time is +2, that of DST is +3.)
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
11
2
4
9
8
6
14
5 7
10
17
16
15
3
12
20
26
22
25
21
27
23
24
45
°
30
°
15
°
0
°
15
°
30
°
45
°
150
°
165
°
180
°
165
°
150
°
135
°
120
°
105
°
90
°
75
°
60
°
.
.
.13
19
18