CASIO DW8800AJ-2BZT - Owner's Manual Immediate Download

-- 3 --

2. OPERATION CHART

2-1. QW-1444

· If the contents of the upper part of the display seem to be continually

changing, see "AUTO DISPLAY FUNCTION" for information on how to

stop it.

· Press M to change from mode to mode.

· Press L to illuminate the display for about two seconds. While Morse code

data is on the display in the Morse Code Mode, pressing L does not

illuminate the display.

Timekeeping Mode

Stopwatch Mode

· When the text in the text area of the display contains more than five

characters, it automatically scrolls. Text scrolling in the text area stops

moving whenever an alarm is sounding.

· In any mode other than Stopwatch Mode, the watch automatically returns to

the Timekeeping Mode if you do not perform any button operation for two or

three minutes.

Alarm Mode

Mission Code Mode

Morse Code Mode

Vital Statistics/ID Mode

Contact Code Mode

w Light

Mode

Text area

TIMEKEEPING MODE

In addition to normal timekeeping, the Timekeeping

Mode is also used to set the current time and

date. You can also adjust the seconds count to

"00" at any time by pressing two buttons.

To adjust the seconds count to "00"

In the Timekeeping Mode, press B and C

simultaneously to adjust the seconds count to

00.

· If you press B and C at the same time while

the seconds count is in the range of 30 to 59, the

seconds are reset to 00 and 1 is added to the

minutes. If the seconds count is in the range of

00 to 29, the minutes count is unchanged.

To set the time and date

1. Hold down A while in the Timekeeping Mode until the seconds digits start

to flash on the display. The seconds flash because they are

selected.

· While the seconds digits are selected (flashing), press C to reset the

seconds to 00.

2. Press M to change the selection in the following sequence.

3. While any other digits (besides seconds) are selected (flashing), press C

to increase the number or B to decrease it. Holding down either button

changes the current selection at high speed.

· While any digits are selected, press L to switch between the 12-hour and

24-hour formats.

· When the 12-hour format is selected, the 12H indicator appears in place

of the day of the week in the text area of the display. With the 12-hour

format, the P indicator appears on the display to indicate "p.m." times.

There is no indicator for "a.m." times.

Selecting the 24-hour format causes the 24H indicator to appear in place

of the day of the week in the text area, and the 24 indicator to appear on the

display.

4. After you set the time and date, press A to return to the Timekeeping

Mode.

· The day of the week is automatically set in accordance with the date.

· The date can be set within the range of January 1, 1995 to December 31,

2039.

· If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping

Mode automatically.

About the backlight

Press L to illuminate the display for about two seconds. While Morse code

data is on the display in the Morse Code Mode, pressing L does not

illuminate the display.

Notes

· The backlight of the watch employs an electro-luminescent (EL) light, which

loses illuminating power after very long use.

· The backlight remains lit for about two seconds from the point you press

L , even if it already lit when you press L . If you keep L depressed for

one or two minutes, the backlight will automatically turn off.

· The illumination provided by the backlight may be hard to see when viewed

under direct sunlight.

Seconds

Hour

Minutes

Year

Month

Date

Text area

Month Date

PM indicator

Hour : Minutes

Seconds

Year

Day of week

· The backlight automatically stops illuminating whenever an alarm sounds.

· The watch will emit an audible sound whenever the display is illuminated.

This is caused by a transistor that vibrates when the EL panel lights up. It

does not indicate malfunction of the watch.

CONTACT CODE MODE

The Contact Code Mode lets you store up to

100* sets of contact data (such as telephone

numbers). Stored data is sorted automatically

into alphabetic sequence based on the text

area text.

* The Contact Code Mode shares memory with

the Mission Code Mode. This means that the

maximum number of Contact Code Mode

entries you can store is reduced by one each

time you store a Mission Code Mode data

item.

· Whenever you enter the Contact Code Mode,

the text CONTACT CODE scrolls across

the text area of the display once. Next, contact

code data appears on the display. You can

interrupt scrolling of the initial text and

immediately display contact code data at any

time by pressing A , B , or C .

· See the "CHARACTER LIST" at the back of this manual for details on how

the watch sorts data.

· The data item that appears on the display when you enter the Contact Code

Mode is the same one that was displayed the last time you exited the

Contact Code Mode.

Text area

Mode indicator

Remaining

memory

To input new contact code data

1. In the Contact Code Mode, press B and C at

the same time to display the new data display.

· If there is no contact code data stored in memory

yet, the new data display appears as soon as

you enter the Contact Code Mode.

· If the message FULL appears in the text area

of the display, it means that memory is full. To

store more data, you will first have to delete

some of the data stored in memory.

2. Hold down A until the flashing cursor appears in the text area of the

display.

3. Input a name in the text area and a contact number in the number area.

· You can input up to eight characters in the text area, and 12 digits in the

number area.

· You can input only hyphens, numbers and spaces in the number area (you

cannot input text).

Use B and C to input characters, and M to move the cursor around the

display. For details, see "INPUTTING TEXT".

4. After inputting your data, press A to store it and return to the Contact

Code Mode.

· When you press A to store data, the message SORT appears on the

display for a few seconds. After the sort operation is complete, the normal

Contact Code Mode display (without the cursor) appears.

Cursor

Text area

Number area

[New Data Display]

GENERAL GUIDE

-- 4 --

To recall contact code data

In the Contact Code Mode, press C to scroll forward through stored data

items or B to scroll in reverse.

· Holding down either button scrolls through the data at high speed.

· The new data display appears whenever scrolling reaches the beginning or

the end of data currently stored in memory.

To edit contact code data items

1. In the Contact Code Mode, scroll through the data items and display the

one you want to edit.

2. Hold down A until the flashing cursor appears in the text area of the

display.

3. Use M to move the cursor to the character you want to change.

4. Change the character.

· See "INPUTTING TEXT" for details.

5. After making the changes that you want, press A to store them and return

to the Contact Code Mode.

To delete contact code data

1. In the Contact Code Mode, scroll through the data items and display the

one you want to delete.

2. Hold down A until the flashing cursor appears in the text area of the

display.

3. Press B and C at the same time to delete the contact code data item.

· At this time the cursor appears in the text area, ready for input.

4. Press A and then L to return to the Contact Code Mode.

Remaining

memory

MISSION CODE MODE

Mission Code Mode lets you store up to 100*

mission code data items (mission time, date,

and text). Whenever a mission time is reached,

an alarm sounds and the text you input for the

mission scrolls across the text area of the

display.

* The Mission Code Mode shares memory with

the Contact Code Mode. This means that the

maximum number of Mission Code Mode

entries you can store is reduced by one each

time you store a Contact Code Mode data

item.

· Whenever you enter the Mission Code Mode,

the text MISSION CODE scrolls across

the text area of the display once. Next, mission

code data appears on the display. You can

interrupt scrolling of the initial text and

immediately display mission code data at any

time by pressing A , B , or C .

Notes

· A Mission Code Alarm sounds whenever a mission time you set is reached.

It continues for about 20 seconds or until you interrupt it by pressing any

button.

· The mission code text scrolls across the text area of the display only if the

watch is in the Timekeeping Mode when the mission code time is reached.

The text continues to scroll for about 25 seconds, or until you stop it by

pressing any button after you press a button to interrupt the alarm.

· Mission Code Mode data items are automatically sorted into chronological

order.

· Entering the Mission Code Mode causes data for the next scheduled

mission to appear on the display.

To input new mission code data

1. In the Mission Code Mode, press B or C until

the new data display appears.

· If there is no mission code data stored in memory

yet, the new data display appears as soon as

you enter the Mission Code Mode.

· If the message FULL appears in the text area

of the display, it means that memory is full. To

store more data, you will first have to delete

some of the data stored in memory.

2. Hold down A until the month setting starts to flash in the number area of

the display. The month setting flashes because it is

selected.

· The initial mission time setting is always midnight, which is indicated as

12:00 with the 12-hour timekeeping format and 0:00 in the 24-hour format.

You can select the timekeeping format in the Timekeeping Mode.

3. Press M to change the flashing selection in the following sequence.

* 11 spaces are provided for the text. This means that if you input only five

characters for the text, so you have to press M 6 times to reach the month

setting.

Text area

Mode indicator

Text

Month Date

Text area

Number area

[New Data Display]

Month

Date

Minutes

Hour

Text *

Hour : Minutes

4. While the month, date, hour or minutes is flashing, press C to increase

the selected setting or B to decrease it. Holding down either button

changes the current selection at high speed.

Important!

· Correct storage of mission code data is impossible if you do not input a

month and date.

· The date you can specify must be within one year from the current date.

This means that if the current date (in the Timekeeping Mode) is June 30,

1996, you will be able to specify any date up to June 29, 1997 for a mission

date.

· When setting the time using the 12-hour format, take care to set the time

correctly as morning (no indicator) or afternoon (P).

5. Input text in the text area of the display.

· You can input up to 11 characters for the text.

Use B and C to input characters, and M to move the cursor around the

display. For details, see "INPUTTING TEXT".

6. After inputting your data, press A to store it and return to the Mission

Code Mode.

· Mission code data remains in memory until you delete it. Be sure to delete

old mission code data whenever you no longer need it. See "To delete

mission code data".

To recall mission code data

In the Mission Code Mode, press C to scroll forward through stored data

items or B to scroll in reverse.

· Holding down either button scrolls through the data at high speed.

· The new data display appears whenever scrolling reaches the beginning or

the end of data currently stored in memory.

To edit mission code data items

1. In the Mission Code Mode, scroll through the data items and display the

one you want to edit.

2. Hold down A until the month setting starts to flash in the number area.

3. Use M to move the flashing to the part of the mission code data item you

want to change.

4. Use B and C to change the data.

· See "To input new mission code data" for details on inputting data.

5. After making the changes that you want, press A to store them and return

to the Mission Code Mode.

To delete mission code data

1. In the Mission Code Mode, scroll through the data items and display the

one you want to delete.

2. Hold down A until the month setting starts to flash in the number area.

3. Press B and C at the same time to delete the mission code data item.

· The message CLEAR appears for a short while. Next, the month setting

starts to flash on the display, ready for input of new data.

4. Press A and then L to return to the Mission Code Mode.

Text area

Mode indicator

Morse code data

MORSE CODE MODE

The Morse Code Mode lets you store up to 16

characters as text or Morse code data. Stored

data can be converted between plain text and

its Morse code equivalent with the touch of a

button.

· Whenever you enter the Morse Code Mode,

the text MORSE CODE scrolls across the

text area of the display once. Next, Morse

code data appears on the display. You can

interrupt scrolling of the initial text and

immediately display Morse code data at any

time by pressing A , B , or C .

· When displaying Morse code data in the text

area of the display, the watch first displays

the

indicator for about two or three seconds,

followed by the Morse code data.

Using Morse Code

Morse code is a system of representing letters of the alphabet and numbers

using short and long elements called "dots" (

) and "dashes" (

). This

watch shows Morse code in the text area of the display using "

" and "

symbols, with the codes for each letter separated by spaces.

-- 5 --

Notes

· This watch displays up to five code elements (dots, dashes) per character.

This means the six-element Morse codes (representing punctuation marks)

are not included.

· You can set up the watch to emit beeps or to silently blink its backlight in

accordance with the dots and dashes of Morse code data as it scrolls

across the text area of the display.

Morse Code Data Example:

In the following example, imagine you want to sound a Morse code message

that tells your friend to meet you at the park at 3 o'clock. One way you could

do this would be to sound a message like the following.

Park, 3 =

· See the "MORSE CODE TABLE" at the back of this manual for a complete

list of Morse code equivalents for Japanese phonetic characters (

katakana),

alphabetical characters, and numbers.

To input text

1. In the Morse Code Mode, use C to select text

input.

· Each press of C changes the input mode and

indicator in the following sequence.

2. Hold down A until the flashing cursor appears in the text area of the

display.

3. Input the text you want in the text area.

· You can input up to 16 characters in the text area.

· You can input Japanese phonetic characters (katakana), alphabetical

characters, and numbers in the text area. You cannot input punctuation

marks.

Use B and C to input characters, and M to move the cursor around the

display. For details, see "INPUTTING TEXT".

4. After inputting the text, press A to store it and return to the Morse Code

Mode.

Conversion between Text and Morse Code

In the Morse Code Mode, press C to convert the data in the text area of the

display between text and its Morse code equivalent. See step 1 under "To

input text" for details on converting data.

· If the text data consists of more than five characters, the text scrolls on the

display from right to left. Morse code data always scrolls across the text

area of the display, regardless of how long it is.

· When displaying Morse code data in the text area of the display, the watch

first displays the

indicator for about two or three seconds, followed by

the Morse code data. See "Selecting Audible or Visible Morse Code" for

details about the

indicator.

· Pressing B while Morse code data is scrolling in the text area stops the

scrolling. Press B again to resume scrolling.

· Characters for which there is no Japanese phonetic characters (katakana),

alphabetical characters, and numbers equivalent for Morse code you input

are replaced by " " in the text area of the display when you press C to

convert from Morse code to text. Characters replaced by "

" are converted

to "

" when you change to the Morse code input display.

· Pressing A or L while Morse code data is scrolling in the text area

restarts the scrolling operation from the beginning of the Morse code data.

Selecting Audible or Visible Morse Code

You can set up the watch to emit beeps or to silently blink its backlight in

accordance with the dots and dashes of Morse code data as it scrolls across

the text area of the display.

Cursor

Text area

A-Z indicator

MORSE

JPN

MORSE

Morse code

input

Japanese

input

Alphabet

input

To check the current Morse code output setting

1. In the Morse Code Mode, press C to display

Morse code.

· Remember that the

indicator initially appears

in the text area for about two or three seconds

after you press C to display Morse code data.

2. Before the

indicator is replaced by the Morse

code data, press B to change the Morse code

output setting in the following sequence.

3. After you make the setting you want, wait about two or three seconds and

the watch will automatically switch to the Morse code data display.

· As the Morse code data scrolls across the text area of the display, it will

perform the output operation in accordance with the setting you make

above.

· The Morse code output operation is performed for one scroll operation only.

· If an Alarm Mode alarm time or Mission Code Mode alarm time is reached

while a tone or backlight Morse code output operation is being performed,

the Morse code output operation is terminated and the applicable alarm

operation is performed.

indicator

Off

Backlight

Tone

To edit text

Note that you can edit text you input in the Morse Code Mode only. You

cannot edit Morse code data. After editing the text data you can convert the

new data to Morse code.

1. In the Morse Code Mode, press C to display the existing text data in the

text area of the display.

2. Hold down A until the flashing cursor appears in the text area.

3. Use M to move the cursor to the character you want to change.

4. Change the character.

· See "INPUTTING TEXT" for details on text input.

5. After making the changes that you want, press A to store them and return

to the Morse Code Mode.

To delete Morse Code Mode data

You can use the following procedure to delete either Morse code data or text

data. When you do, the corresponding Morse code or text data is also

deleted.

1. While in the Morse Code Mode, hold down A .

· If text is in the text area, hold down A until the cursor appears. In the case

of Morse code data, hold down A until the data starts to flash.

2. Press B and C at the same time to delete the data in the text area.

· When deleting Morse code data, pressing any button except A deletes the

code data.

· At this time, either _ (if you deleted text data) or

(if you deleted Morse

code data) appears in the text area of the display, ready for new input.

3. Input new data or press A to return to the Morse Code Mode.

To input new Morse code data

1. In the Morse Code Mode, use C to select

Morse code input.

· The MORSE indicator appears on the display

during Morse code input.

2. Hold down A until

appears in the text area

of the display.

3. Input the Morse code that you want in the text

area.

· Press B to input dots ( ) and C to input dashes ( ). Press M to input

spaces between each character, and L to backspace and delete the dot or

dash to the left.

· Be sure to input a space between each set of dots and dashes, and make

up a character. This watch is designed to allow up to five dots and dashes

per character, so further input becomes impossible after you input the fifth

dot or dash in a series that does not include a space.

4. After inputting your Morse code data, press A to store it and return to the

Morse Code Mode.

· Morse code data always scrolls across the text area of the display, regardless

of how long it is.

Text area

MORSE indicator

VITAL STATISTICS/ID MODE

The Vital Statistics/ID Mode provides a handy

place to store data about your vital statistics

(name, blood type, date of birth) and personal

identification (ID) data (credit card number,

license number, passport number, and two

undefined items).

· Whenever you enter the Vital Statistics/ID

Mode, the text VITAL

STATS./ID

scrolls across the text area of the display

once. Next, the name screen appears on the

display. You can interrupt scrolling of the initial

text and immediately display the name screen

at any time by pressing A , B , or C .

· The name screen always appears first

whenever you enter the Vital Statistics/ID

Mode.

Important!

· Once you input your vital statistics, take care that the watch is not borrowed

by another person. Otherwise, emergency medical personnel may assume

that the data in the Vital Statistics/ID Mode applies to the person who is

currently wearing the watch.

· Note that storing important personal identification data in the watch's

memory runs the risk of it being misused should you lend the watch to

someone or should the watch become lost or stolen. Because of this, the

manufacturer strongly recommends that you input such important information

in coded form that cannot be deciphered by others.

· Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or

any third party for any losses or damages suffered through the misuse of

data stored in the memory of this watch.

Mode indicator

Text area

Number area

-- 6 --

To input the date of your birth

1. In the Vital Statistics/ID Mode, display the

BIRTH screen.

2. Hold down A until the year digits start to flash

on the display. The year digits flash because

they are

selected.

3. Press M to change the selection in the following

sequence.

4. Press C to increase the selected digits and B to decrease them. Holding

down either button changes the selected digits at high speed.

· The year can be set in the range of 1900 to 2039.

5. After inputting your data, press A to store it and return to the normal

BIRTH screen (no flashing digits).

Personal identification data

· This watch has three built-in titles for personal identification data: CREDIT

(for a credit card number), LICENCE (for a license number), and

PASSPORT (for a passport number). You can use these built-in title as

they are, or append eight more characters to a built-in title to indicate a

credit card company name, for example.

· In addition to the three built-in titles, you can also input your own titles up to

eight characters long for the two undefined items.

· You can input number up to 12 digits long for each personal identification

data item.

Month Date

Year

Month

Date

To input your blood type

1. In the Vital Statistics/ID Mode, display the

BLOOD screen.

2. Hold down A until the Rh factor setting flash in

the text area of the display.

3. Use B and C to scroll through the available

Rh factor settings in the following sequence.

4. Press M to advance to the blood type.

5. Use B and C to scroll through the available blood type settings in the

following sequence.

6. After inputting your data, press A to store it and return to the normal

BLOOD screen (no flashing characters).

· Select --- if you do not want to specify an Rh factor and -- if you do not

want to select a blood type in the above sequence. When neither an Rh

factor nor blood type is specified, the blood data screen shows ----- on

the watch's display.

---

Blood type ABO

Rh factor

Press C

Press B

Press C

Press B

To input personal identification data

1. In the Vital Statistics/ID Mode, display the

personal identification data screen where you

want to input data.

· See "To recall Vital Statistics/ID data" for details

on how to switch between data screens.

2. Hold down A until the flashing cursor appears

in the text area of the display.

3. Input a text in the text area if you want.

· In the case of a built-in title, you can append up to eight characters to the

preset title. For the undefined data items, you can input titles up to 8

characters long.

· To use a built-in title as it is without appending text, press M eight times to

move the cursor to the number area.

Use B and C to input characters, and M to move the cursor around the

display. For details, see "INPUTTING TEXT".

4. After you input your text, use M move the cursor to the number area and

input number data.

· You can input up to 12 digits in the number area.

· You can input only hyphens, numbers and spaces in the number area (you

cannot input text).

5. After inputting your data, press A to store it and return to the screen you

started out from in step 1 of this procedure.

To edit Vital Statistics/ID Mode data

1. In the Vital Statistics/ID Mode, scroll through the data items and display

the one you want to edit.

2. Hold down A until the data on the display starts to flash.

3. Use M to move the flashing to the part of the data item you want to

change.

4. Use B and C to change the displayed data.

· For details on inputting data, see the sections of this manual that describes

input for each screen.

5. After making the changes that you want, press A to store them and return

to the screen you started out from in step 1 of this procedure.

To delete Vital Statistics/ID Mode data items

1. In the Vital Statistics/ID Mode, scroll through the data items and display

the one you want to delete.

2. Hold down A until the data on the display starts to flash.

3. Press B and C at the same time to delete the data item.

4. Press A to return to the screen you started out from in step 1 of this

procedure.

Number area

Cursor

Text area

ALARM MODE

When the Daily Alarm is switched on, the alarm

sounds for 20 seconds at the preset time each

day. Press any button to stop the alarm after it

starts to sound.

When the Hourly Time Signal is switched on, the

watch beeps every hour on the hour.

To set the alarm time

1. Hold down A while in the Alarm Mode until the

hour digits start to flash on the display. The

hour digits flash because they are

selected.

· This operation will switch the Daily Alarm on

automatically.

2. Press M to change the selection in the following

sequence.

3. Press C to increase the selected digits or B to decrease them. Holding

down either button changes the selection at high speed.

· The format (12-hour and 24-hour) of the alarm time matches the format you

select for normal timekeeping.

· When setting the alarm time using the 12-hour format, take care to set the

time correctly as morning (no indicator) or afternoon (P).

4. After you set the alarm time, press A to return to the Alarm Mode.

To switch the Daily Alarm and Hourly Time Signal on

and off

Press C while in the Alarm Mode to change the status of the Daily Alarm and

Hourly Time Signal in the following sequence.

Alarm on indicator

Hour

Minutes

[Alarm ON indicator/Hourly Time Signal ON indicator]

Both ON

Mode indicator

Hour

Minutes

Hourly time signal

on indicator

Both OFF

Daily Alarm

Only

Hourly Time

Signal only

To recall Vital Statistics/ID data

In the Vital Statistics/ID Mode, press B or C to change the data on the

display in the following sequence.

· The titles of the each data item appear in the text area of the display. In the

case of the undefined items, you can specify titles that appear in the text

area whenever you later display that item.

NAME

(Name)

BLOOD

(Blood type)

CREDI

(Credit card

number)

BIRTH

(Date of birth)

(Undefined)

LICEN

(License

number)

PASSP

(Passport

number)

Press C

Press B

To input your name

1. In the Vital Statistics/ID Mode, display the

NAME screen.

2. Hold down A until the flashing cursor appears

in the text area of the display.

3. Input your name into the text area.

· You can input up to 16 characters for your name.

Use B and C to input characters, and M to

move the cursor around the display. For de-

tails, see "INPUTTING TEXT".

· You can clear the characters currently input for the name by pressing B

and C at the same time.

4. After inputting your data, press A to store it and return to the normal

NAME screen (without cursor).

Text area

Cursor

-- 7 --

INPUTTING TEXT

The following describes how to input text in the Contact Code Mode, Mission

Code Mode, Morse Code Mode, and Vital Statistics/ID Mode.

How to input characters

1. When the cursor is blinking in the text area of

the display, use B and C to scroll through the

available letters, numbers and symbols, in the

following sequence.

· Holding down either button scrolls through at high speed.

· You can input Japanese phonetic characters (katakana), alphabetical

characters, numbers, and symbols in the text area. For a complete list of

characters you can input, see the "CHARACTER LIST" at the back of this

manual.

2. When the character you want at the cursor position is shown, press M to

move the cursor to the right.

3. Repeat steps 1 and 2 until your text is complete.

· You can input only hyphens, numbers and spaces in the number area. Each

press of B or C changes the input at the current cursor location in the

following sequence.

· If you do not perform any button operation for about two or three minutes

while the cursor is on the display, the watch automatically returns to the

normal data display (the cursor disappears).

(space)

A to Z

(Alphabet)

0 to 9

)

(

Press C

Press B

(Japanese)

Number area

Cursor

Text area

Press C

Press B

(space)

0 to 9

AUTO DISPLAY FUNCTION

The Auto Display function continually changes the

contents of the text area of the display. Note that

you cannot use any of the watch's other functions

(except for turning on the backlight and adjusting

the seconds count to zero) while the Auto Display

function is operating.

To turn the Auto Display off

Hold down M for about three seconds until the

watch beeps.

To turn Auto Display on

Hold down M for about three seconds until the watch beeps.

Note

The Auto Display function cannot be performed while you are making settings

(i.e. while digits or other settings are flashing on the display).

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed

time, split times, and two finishes. The range of

the stopwatch is 23 hours, 59 minutes, 59.99

seconds.

(a) Elapsed time measurement

(b) Split time measurement

Start

Stop

Split release

Re-start

Stop

Record time of

second runner.

Second runner finishes.

Record time of first runner.

Split

First runner

finishes.

Clear

Start

Stop

1/100 second

Mode indicator

Seconds

Minutes

Hours

ABOUT THE LOW BATTERY WARNING

The message BATT flashes on the display

whenever the battery power is low. Have the

battery of the watch replaced as soon as possible

after this message appears. Using the watch while

the battery is low can result in abnormal operation.

Important!

· In order to protect data stored in memory, you will not be able to recall

existing data or input new data while the BATT message is flashing on the

display. Also, the alarm, hourly time signal, backlight, and other functions

do not operate.

· Low battery power can cause time keeping to fall behind, and it can cause

the display to become difficult to read, or to clear completely.

ALWAYS LEAVE BATTERY REPLACEMENT UP TO THE DEALER

WHERE YOU BOUGHT THE WATCH OR TO AN AUTHORIZED CASIO

DISTRIBUTOR. BE SURE TO SHOW THE FOLLOWING INFORMATION

TO THE PERSON REPLACING THE BATTERY.

Attention dealer or CASIO distributor

Be sure to use the following procedure when replacing the battery.

1. Open and remove the back cover.

· If CLOSE appears on the display when you open the back cover, replace

the back cover. Wait for a few minutes and try again.

2. Remove the battery holder.

3. Remove the old battery and load a new one.

4. Replace the battery holder.

5. Touch the AC contact and the battery (+) side with metallic tweezers.

6. Close the back cover.

· The message WAIT appears on the display about 15 seconds after you

perform the AC (all clear) operation in step 5 of the above procedure,

indicating that the watch is performing an internal self-check for data errors.

· The WAIT indicator remains on the display for a few minutes while the

watch performs an internal check of data in memory. Though you can

change the time setting of the watch while the WAIT indicator is on the

display, other operations are disabled.

To test the alarm

Hold down B while in the Alarm Mode to sound the alarm.

(

)

CHARACTER LIST

(space)