-- 4 --
2-2. QW-1825
Elapsed time measurement
EEEEB
Start
Stop
Re-start
Stop
Clear
Split time measurement
EBBEB
Start
Split
Split release
Stop
Clear
Split time and 1st-2nd place times
EBEBB
Start
Split
Stop
Split release
Clear
GENERAL GUIDE
· Press C to change from mode to mode.
· In any mode (except when making countdown alarm settings) press D to illuminate the digital display.
Caution
· The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use.
· Frequent use of the backligfht shortens the battery life.
· The watch emits an audible sound whenever the display is illuminated. This is because the EL light vibrates slightly when lit. It does not indicate malfunction of the watch.
Timekeeping Mode
SUN
6 30
10 5850
AB
E
D
C
ST
6 00
0 0000
AL
6
6 45
TR
6 0
0 0000
Stopwatch Mode
Countdown Alarm Mode
Alarm Mode
TIMEKEEPNG MODE
To set the time and date
1. Hold down A while in the Timekeeping Mode
until the seconds digits flash on the display.
2. Press C to change the selection (flashing) in the
following sequence.
SUN
6 30
10 5850
AB
E
D
C
Month
Day
PM indicator
Day of week
3. While the seconds setting is selected (flashing), press E to reset it to 00. If you
press E while the seconds setting is in the range of 30 to 59, the seconds are reset
to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00 to
29, the minutes count is unchanged.
4. While any other setting (beside seconds) is selected (flashing), press E to increase
it or B to decrease it. While the 12/24-hour format setting is selected, press E to
toggle it between 12 and 24.
· Except for the seconds or 12/24-hour setting, holding down a button changes the
setting at high speed.
· When the 12-hour format is selected, the indicator P appears on the display to
indicate "P.M." times. There is no indicator for "A.M." times.
5. After you set the time and date, press A to return to the Timekeeping Mode.
· The day of the week is automatically set in accordance with the date.
· The date can be set within the range of January 1, 1995 to December 31, 2039.
· If you do not operate any button for a few minutes while a setting is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
ABOUT THE EL ALARM
While the EL alarm feature is turned on, the watch's EL backlight flashes along with
the audible tone when a daily alarm time is reached, when the hourly time signal
sounds, or when the end of a countdown alarm operation is reached. Pressing D
while the EL alarm feature is turned on causes the display to remain illuminated for
Hour
Seconds
Seconds
12/24-Hour
Format
STOPWATCH MODE
The stopwatch Mode lets you measure elapsed
time, split times, and two finishes. The range of the
stopwatch is 23 hours, 59 minutes, 59.99 seconds.
You can use the EL backlight at any time while the
stopwatch is operating.
SUN
6 30
10 5850
D
B
SUN
6 30
10 5850
D
B
ON
OFF
EL Alarm indicator
Hold down B
ST
6 00
0 0000
B
E
Mode indicator
Seconds
Hours
Minutes
1/100
seconds
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 1
second to 24 hours. When the countdown reaches
zero, an alarm sounds for 10 seconds or until you
press any button.
To set the countdown start time
1. Hold down A while in the Countdown Alarm
Mode. The hour setting flashes on the display
because it is selected.
2. Press C to change the selection in the following
sequence.
Hour
Minutes
Seconds
Minutes
Minutes
TR
0
0 0000
A
B
E
D
C
Seconds
Hours
1/10
seconds
3. Press E to increase the selected setting or B to decrease it. Holding down either
button changes the setting at high speed.
· To set the starting value of the countdown time to 24 hours, set 0:00'00".
4. After you set the countdown start time, press A to return to the Countdown Alarm
Mode.
· If you do not operate any button for a few minutes while a setting is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode automatically.
To use the countdown alarm
1. Press E while in the Countdown Alarm Mode to start the countdown alarm.
2. Press E again to stop the countdown alarm.
· You can resume a paused countdown alarm operation by pressing E.
3. Stop the countdown alarm and then press B to reset the countdown time to its
starting value.
· When the end of the countdown is reached and auto repeat timing is off, the alarm
TR
0 1500
D
B
A
E
C
TR
0 1500
D
B
A
E
C
OFF
ON
Press D
Auto repeat indicator
Hour
Minutes
Day
Month
Year
3. Press A to return to the Countdown Alarm Mode.
· When the end of the countdown is reached while auto repeat is on, the alarm
sounds, but the countdown restarts from the beginning without stopping. You can
stop the countdown by pressing E and manually reset to the start time by pressing
B.
· When the starting value of the countdown time is set at 10 seconds or less and auto
repeat is turned on, the countdown alarm tone sounds for only one second instead
of the normal 10 seconds. If the EL Alarm is turned on, the EL backlight does not
flash under the above conditions.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset
time each day. Press any button to stop the alarm after it starts to sound. When the
Hourly Time Signal is on, the watch beeps every hour on the hour.
AL
6 45
A
B
E
D
C
Mode indicator
Alarm on indicator
Hours
Minutes
Hourly time signal
on indicator
five seconds, instead of the normal two seconds when the EL alarm is turned off.
To turn the EL Alarm feature on and off
· In the Timekeeping Mode, hold down B until the EL Alarm indicator appears on (EL
alarm on) or disappears from (EL alarm off) the display.
sounds for 10 seconds or until you stop the alarm by pressing any button.
Countdown timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.
To turn auto repeat timing on and off
1. Hold down A while in the Countdown Alarm Mode until the hour setting flashes.
2. Press D to turn auto repeat on and off.
Mode indicator
-- 5 --
To set the alarm time
1. Hold down A until the hour setting starts to flash on the display. The hour setting
flashes because it is selected.
· This operation automatically turns on the Daily Alarm.
2. Press C to change the selection in the following sequence.
3. While the hour or minutes setting is selected (flashing) press E to increase it or B
to decrease it. Holding down either button changes the current setting at high
speed.
· The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P).
4. After you set the alarm time, press A to return to the Alarm Mode.
· If you do not operate any button for a few minutes while a setting is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To turn the daily alarm and hourly time signal on and off
Press B while in the Alarm Mode to change the status of the daily alarm and hourly
time signal in the following sequence.
· The alarm on indicator (ALM) and the Hourly Signal on indicator (SIG) are shown on
the display in all modes while these functions are turned on.
To test the alarm sound
Hold down E while in the Alarm Mode to sound the alarm.
Hour
Minutes
Hourly Time
Signal Only
SIG
ALM SIG
Both ON
Both OFF
Daily Alarm
Only
ALM