background image
CT-X432M YU
STEREO CAR CASSETTE RECEIVER
RADIO-CASSETTE ESTEREOFONICO PARA AUTOMOVIL
OPERATING INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MODE D'EMPLOI
OWNER'S RECORD
For your convenience, record the model number and
serial number (you will find them on the bottom side of
your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of
difficulty.
Model No. CT-X432M
Serial No.
ENGLISH
ESPAÑOL
FRANÇAIS
8C-KTF-901-01
011130ATM-OX


background image
1 ENGLISH
PRECAUTIONS
· Use only in a 12-volt DC negative-ground electrical
system.
· Disconnect the vehicle's negative battery terminal
while mounting and connecting the unit.
· When replacing the fuse, be sure to use one with an
identical amperage rating. Using a fuse with a higher
amperage rating may cause serious damage to the
unit.
· Keep screwdrivers, etc. and other metallic or magnetic
objects away from the playback head.
· When your vehicle has been parked in direct sunlight
resulting in a considerable rise in the temperature
inside, allow the unit to cool off before operating it.
· Keep the volume at a level at which you can hear
outside warning sounds (horns, sirens, etc.).
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment
and receiver.
-- Connect the equipment into an outlet on circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Modifications or adjustments to this product, which are
not expressly approved by the manufacturer, may void
the user's right or authority to operate this product.
1 ENGLISH
TABLE OF CONTENTS
THEFT PROTECTION .............................................. 2
BASIC OPERATION, AUDIO AND CLOCK
ADJUSTMENT ..................................................... 2
RADIO OPERATION ................................................ 3
TAPE PLAYBACK ..................................................... 5
AUXILIARY EQUIPMENT ......................................... 6
OTHER FUNCTIONS ............................................... 6
CD CHANGER OPERATION .................................... 6
TROUBLESHOOTING .............................................. 7
MAINTENANCE ........................................................ 8
SPECIFICATIONS .................................................... 8
Note
Some buttons are assigned two or more functions.
For detailed descriptions, refer to the related pages.
Notes on cassettes
Do NOT expose cassettes to direct sunlight, extremely
high or cold temperature or moisture.
Keep cassettes away from equipment with built-in
magnets to avoid unwanted noise or loss of sound
quality.
Do NOT touch the tape of a cassette, as any dirt or dust
will contaminate the heads.
Be sure to remove any cassette from the unit if you are
not using it.
DEMO (Demonstration) mode
The unit has an extra display (DEMO) mode which
demonstrates the operation modes of the unit. The unit
switches to DEMO mode automatically if you turn the
unit on and leave it as it is for 5 seconds after all the
connections have been completed.
To cancel DEMO mode
1 During DEMO mode, press and hold SRC until
"CONT." appears in the display.
2 Press i or k to select "DEMO."
3 Turn AUDIO CONTROL to select "DEMO OFF."
To resume DEMO mode, select "DEMO ON" in step 3.
Caution on the transit protection pad
Be sure to remove the pad before operating the unit.
Transit protection pad


background image
ENGLISH
2
ENGLISH
2
THEFT PROTECTION
Take the front panel with you when leaving the car, and
keep it in the supplied carrying case.
Detaching the front panel
Before detaching the front panel, remove the cassette to
prevent possible damage to the unit.
1 Press z to remove the cassette.
2 Press and hold PWR/MUTE until the unit turns off.
3 Press %. (Hold the panel with one hand to prevent
accidentally dropping it.)
4 Remove the panel.
Attaching the front panel
1 Engage the left side of the front panel to the left catch
on the unit.
2 Push the panel forward until it locks. Be sure not to
press any buttons while you are attaching the panel.
Note
Do not touch the connector on the reverse side of the
front panel. This could cause a poor or faulty connection.
BASIC OPERATION,
AUDIO AND CLOCK
ADJUSTMENT
PWR/MUTE
SEL
DISP
BAND
SRC
AUDIO CONTROL
i/k
Turning the unit on/off
· You can turn the unit on by pressing any button on the
front panel except
%, z, f, g and AUDIO
CONTROL. The unit also turns on when you insert a
cassette.
· Press and hold PWR/MUTE until the unit turns off.
Note
Most operations described in this manual require
the unit to be turned on before starting the operation,
unless explicitly stated otherwise.
Changing the source mode
1 Press SRC.
Pressing SRC cycles through source modes in the
following order:
* Tape Play mode (available while a cassette is in the
unit)
** CD Changer Play mode (available when an optional
CD Changer is connected)
Adjusting the volume
1 Turn AUDIO CONTROL.
VOL (volume) indicator flashes.
Muting the sound
1 Press PWR/MUTE briefly.
MT indicator flashes.
To restore volume, briefly press PWR/MUTE again.
ENGLISH


background image
3 ENGLISH
3 ENGLISH
Adjusting sound
You can select the following modes for adjusting sound
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/rear) and H-BASS (high bass).
1 Press SEL repeatedly to select the mode to be
adjusted.
Pressing SEL cycles through the modes. The
selected mode's indicator flashes (except for H-
BASS).
2 Turn AUDIO CONTROL to increase or decrease the
level for the selected mode (except for H-BASS).
In H-BASS mode, turn AUDIO CONTROL to select
1, 2, 3 or off.
Note
Adjust the level or select on/off within 5 seconds, or the
selected mode will return to previous state.
Aligning the source levels
(Source Level Adjuster)
Volume may vary each time you change the source
mode. In this case, you can align each source mode's
volume to almost the same level.
1 Press SRC or BAND repeatedly to select the desired
mode.
2 Press DISP while pressing SEL.
"LEVEL 0" appears in the display.
3 Turn AUDIO CONTROL to adjust the level.
Note
Adjust the level within 5 seconds, or the selected mode
will be canceled.
Restoring the factory settings
1 Turn off the unit.
2 Press and hold DISP until "LEVEL --" appears in the
display.
Note
You can restore the factory settings only for VOL, BASS,
TRE, BAL, FAD, and H-BASS, and aligned source
volume levels.
Muting button beep sounds
1 Turn off the unit.
2 Press and hold SEL until "BEEP" appears in the
display.
3 Turn AUDIO CONTROL to select ON or OFF.
4 Press SEL.
Setting the clock
1 Press and hold DISP until the clock indicatior
flashes in the display.
2 Press i (to set hour) or k (to set minute), and
then turn AUDIO CONTROL.
3 Press DISP.
Displaying the clock
1 Press DISP.
To return to the former display, press DISP again.
RADIO OPERATION
Tuning in to a station
(Seek/Manual Tuning)
LO
i/k BAND
Band indicator*
Stereo indicator
Frequency indication
Local indicator
* "F" means FM, and "A" means AM.


background image
ENGLISH
4
ENGLISH
4
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1, or A2).
2* Press i (to move to higher frequencies) or k (to
move to lower frequencies) to tune in to a station.
"ST" appears in the display when an FM station is
broadcasting in stereo, and receiving conditions are
good.
*Seek Tuning and Manual Tuning
· Press and hold
i or k until Seek Tuning starts.
The unit locates a station automatically (Seek Tuning).
· Press
i or k repeatedly to search for a desired
station while increasing or decreasing the frequency
step by step (Manual Tuning).
To stop Seek Tuning, press
i or k again.
Monaural mode
When FM signals become weak, or FM reception
becomes poor, the unit automatically switches to
Monaural mode to reduce noise.
Local mode
Local mode allows you to tune in only to strong stations
during Seek Tuning.
1 Press LO before you start Seek Tuning.
"LO" appears in the display.
To return to Distant mode, press LO again.
"LO" disappears and the unit tunes in to all receivable
stations.
Using preset stations
You must preset stations before you can tune in to a
station using preset station number buttons.
i/k BAND
PS/A.ME Preset station buttons 1 to 6
Preset station number
Presetting stations automatically
(Auto Memory)
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1, or A2).
2 Press and hold PS/A.ME until automatic presetting
starts.
The unit automatically stores up to 6 stations for
each band.
After completion of automatic presetting, the unit
tunes in to all the stations stored on the preset
station buttons in order (Preset Scan).
To cancel automatic presetting, press PS/A.ME again.
Checking the preset stations (Preset Scan)
1 Press PS/A.ME briefly.
Each preset station will be tuned in for 5 seconds in
order.
To cancel Preset Scan, press PS/A.ME again or any
preset station button.
Presetting stations manually
(Manual Memory)
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1, or A2).
2 Press i or k to tune in to a desired station (see
"Tuning in to a station" as well for another tuning
method).
3 Press and hold the desired preset station button until
the unit beeps.
Note
A newly preset station replaces the station on the same
band that was previously stored on that preset station
button.
Tuning in to a preset station
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1, or A2).
2 Press the preset station button on which the desired
station is stored.
Active tuning reception control (ATRC)
The unit automatically suppresses FM noise caused by
vehicle movement, and maintains sound quality.