COMPACT DISC STEREO RADIO CASSETTE RECORDER
English : See page 2.
Español : Ver la página 10.
Français : Voir page 18.
INSTRUCCIONES DE MANEJO
Read the Operating Instructions carefully and
completely before operating the unit. Be sure to keep
the Operating Instructions for future reference. All
warnings and cautions in the Operating Instructions and
on the unit should be strictly followed, as well as the
safety suggestions below.
1 Water and moisture
- Do not use this unit near
water, such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, swimming pool,
or the like.
- Do not use this unit near sources of heat,
including heating vents, stoves, or other appliances
that generate heat.
It also should not be placed in temperatures less
than 5°C (41°F) or greater than 35°C (95°F).
3 Mounting surface
- Place the unit on a flat, even
- The unit should be situated with
adequate space around it so that proper heat
ventilation is assured.
Allow 10 cm (4 in.) clearance from the rear and the
top of the unit and 5 cm (2 in.) from each side.
- Do not place the unit on a bed, rug, or similar
surface that may block the ventilation openings.
- Do not install the unit in a bookcase, cabinet, or
airtight rack where ventilation may be impeded.
5 Objects and liquid entry
- Take care that objects or
liquids do not get inside the unit through the
6 Carts and stands
- When placed or
mounted on a stand or cart, the unit
should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the unit
or cart to overturn or fall.
- Moisture may form on the CD
pickup lens when:
- The unit is moved from a cold spot to a warm spot
- The heating system has just been turned on
- The unit is used in a very humid room
- The unit is cooled by an air conditioner
When this unit has condensation inside, it may not
function normally. Should this occur, leave the unit
for a few hours, then try to operate again.
8 Wall or ceiling mounting
- The unit should not be
mounted on a wall or ceiling, unless specified in the
1 Power sources
- Use on batteries or AC house
current, as specified in the Operating Instructions
and marked on the unit.
- As a safety feature, some units are
equipped with polarized AC power plugs which can
only be inserted one way into a power outlet. If it is
difficult or impossible to insert the AC power plug
into an outlet, turn the plug over and try again. If it
still does not easily insert into the outlet, please call
a qualified service technician to service or replace
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated "dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
For your convenience, record the model number (you
will find it at the bottom of the unit) and serial number
(you will find it in the battery compartment) in the space
provided below. Please refer to them when you contact
your AIWA dealer in case of difficulty.
"CAUTION:TO REDUCE THE RISK OF
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The OPE/BATT indicator lights up while the power is
Using on AC house current
Connect the AC cord as illustrated below.
Use only the supplied AC cord. Use with other cords
may result in the risk of fire.
Using on batteries
Open the lid of the battery compartment on the rear and
insert eight R14 (size C) batteries, not supplied, with
0 and 9 marks correctly aligned. Then close the
To switch from AC power supply to battery power
disconnect the AC cord from the AC inlet.
When to replace the batteries
The OPE/BATT indicator becomes dim, the tape speed
slows down, volume decreases, or sound is distorted
Notes on batteries
· Do not mix different types of batteries or old batteries
with new ones.
· When the unit is not to be used for a long period,
remove the batteries to prevent needless battery
· Never recharge the batteries, apply heat to them or
take them apart.
· Remove dead batteries.
If liquid leaks from the batteries, wipe thoroughly to
OPE / BATT
to the AC inlet of the unit
to an AC outlet
(AC 120 V, 60 Hz)
supplied AC cord
the outlet. To avoid defeating the safety feature of
the polarized plug, do not force it into a power outlet.
3 AC power cord
- When disconnecting the AC power cord, pull it out
by the AC power plug. Do not pull the cord itself.
- Never handle the AC power plug with wet hands,
as this could result in fire or shock.
- Power cords should be firmly secured to avoid
being bent, pinched, or walked upon. Pay
particular attention to the cord from the unit to the
- Avoid overloading AC outlets and extension cords
beyond their capacity, as this could result in fire or
4 Extension cord
- To help prevent electric shock, do
not use a polarized AC power plug with an extension
cord, receptacle, or other outlet unless the polarized
plug can be completely inserted to prevent exposure
of the blades of the plug.
5 When not in use
- Unplug the AC power cord from
the AC outlet or remove all the batteries if the unit
will not be used for several months or more. When
the cord is plugged in, a small amount of current
continues to flow to the unit, even when the power is
Clean the unit only as recommended in the Operating
Damage Requiring Service
Have the units serviced by a qualified service
- The AC power cord or plug has been damaged
- Foreign objects or liquid have got inside the unit
- The unit has been exposed to rain or water
- The unit does not seem to operate normally
- The unit exhibits a marked change in performance
- The unit has been dropped, or the cabinet has been
DO NOT ATTEMPT TO SERVICE THE UNIT
FM MODE /
1 Press *RADIO/BAND repeatedly to select
the desired band.
The power is turned on and the previously tuned
station is received.
* or BAND on the remote control when the AC
cord is connected (CSD-TD66 only)
2 Press r, t (TUNING DOWN, UP) to
select a station.
During FM stereo reception,
turn the power off.
For better reception
For quick tuning (Auto Search)
r, t pressed until the tuner starts
searching for a station. When a station is tuned to, the
If the broadcast signal is weak, it does not stop. To
stop the search manually, press
r or t.
* FM MODE/OSC
- If an FM stereo broadcast contains noise, press the
button so that
Noise is reduced, although reception is monaural.
To restore stereo reception, press the button again.
- If a high-pitched sound is heard during AM recording,
press the button repeatedly until the noise is reduced.
Its position can be checked by "·" being on or off the
* or MODE on the remote control (CSD-TD66 only)
To change the AM tuning interval
The default setting of the AM tuning interval is 10 kHz/
step. If you use this unit in an area where the frequency
allocation system is 9 kHz/step, change the interval as
Press RADIO/BAND to display FM.
s while pressing RADIO/BAND to display the
When the AM tuning interval is changed, the preset
stations are cleared.
If the unit picks up noise from other electrical
appliances nearby, like a TV or fluorescent lights, move
the unit away.
To listen with the headphones
Connect headphones with a stereo mini plug to the
jack on the rear of the unit.
Extend the rod antenna
and orient it for the best
The antenna is inside the
unit. Position the unit for
the best reception.
You can preset up to 15 stations in each band.
1 Select a station.
2 Press *s STOP/MEMORY once so that
"M" is displayed to store the station.
A station is assigned a preset number, beginning
from 1 in consecutive order for each band.
s on the remote control (CSD-TD66 only)
3 Repeat steps 1 and 2.
The next station will not be stored if a total of 15
preset stations have already been stored for a
To listen to preset stations
Select a band then press
c PLAY on the remote control is also available (CSD-
To select a preset number directly with the
remote control (CSD-TD66 only)
Press the numbered buttons 0-9 and +10.
To select number 15, press +10 and 5.
To select number 10, press +10 and 0.
To clear a preset station
Select the preset number first. Within 4 seconds, keep
s pressed until "M" and the preset number disappear
in the display.
The higher numbers in the band are decreased by one.
Remote Control (CSD-TD66 only)
Insert two R6 (size AA) batteries.
When the reach of the remote control signal is less than
5 meters (16 feet), replace the batteries.
The remote control may not operate correctly
- The unit is exposed to intense light, such as direct
- Objects block the remote control signal to the unit
To use the buttons on the remote control
Buttons on the remote control and the main unit with
identical indications have the same functions.
To turn the power on
Press POWER to turn on the display.
When using the unit on the batteries, this button will not
turn the power on.
To turn the power off
Press POWER to turn off the display.
When one of the deck operation buttons is pressed, this
button will not turn the power off.
To use the FUNCTION button
Each time FUNCTION is pressed while the power is on,
the function is selected cyclically.
* applicable when one of the deck operation buttons is